Premier Mounts LMV-405 Installation guide

Premier Mounts
Brand
Premier Mounts
Model
LMV-405
Category
Flat panel accessories
Type
Installation guide

This manual is also suitable for

Premier Mounts LMV-405 is a flat-panel spacer engineered to significantly reduce installation time for large video walls. It is model-specific, designed to work seamlessly with most flat panels.

The LMV-405 allows for the installation of multiple LMV mounts using a single spacer. Simply repeat the installation process for each surrounding LMV mount, using the same spacer for each 2x2 installation or as many times as needed to complete an unlimited LMV large matrix video wall.

To ensure proper alignment, the spacer should be plumb and level before marking the corners where the LMV will be mounted. It is recommended to start from the bottom corner and work upwards. Install the second mount in a horizontal direction, ensuring it remains plumb and level, and repeat this step for each mount horizontally.

Premier Mounts LMV-405 is a flat-panel spacer engineered to significantly reduce installation time for large video walls. It is model-specific, designed to work seamlessly with most flat panels.

The LMV-405 allows for the installation of multiple LMV mounts using a single spacer. Simply repeat the installation process for each surrounding LMV mount, using the same spacer for each 2x2 installation or as many times as needed to complete an unlimited LMV large matrix video wall.

To ensure proper alignment, the spacer should be plumb and level before marking the corners where the LMV will be mounted. It is recommended to start from the bottom corner and work upwards. Install the second mount in a horizontal direction, ensuring it remains plumb and level, and repeat this step for each mount horizontally.

Installation Instructions
Installing Multiple LMVs
LMV’s dedicated at-panel spacers are engineered with the knowledge that aligning each at panel on a large wall is time
consuming and costly.These model-specic spacers are available for most at panels, which signicantly reduces installation time.
Step 1
Introduction
LMV Spacer
Refer to your LMV or LMVF installation manual to install the
rst mount in your desired location. Make sure it is level
before moving on with the the spacer installation.
1) Once your LMV is mounted in the desired location and is
level, align your spacer to the top left or right (depending
on your install direction) corner of your mount (Figure 1),
You may use commercially available hardware to secure
the spacer to the wall during installation (depending on the
wall material). You may utilize the same spacer for multiple
LMV/LMVF installations.
Multiple LMV mounts can be installed using one dedicated spacer.
Simply repeat step one when installing each of the surrounding
LMV mounts (Figure 2). Use one spacer for each 2x2 installation
by mounting it to the wall, or utilize the same spacer as many
times needed to complete an unlimited LMV large matrix video
wall.
1. Make sure the spacer is plumb and level and mark each
corner where the LMV will be mounted (or secure to the wall).
It is best to start from the bottom corner and work your way
up.
2. Install the second mount working in a horizontal direction.
3. Ensure that the mount remains plumb and level.
4. Repeat this step for each mount horizontally
5. To install multiple rows, place spacer between previously
installed LMVs on the bottom row. Make sure the spacer is
plumb and level, mark the corners (or secure to the wall) to
be sure of where the LMV should be and install your mount.
(Figure 2)
(Figure 1)
This spacer is shown for illustration purposes only. Your spacer
may look different depending on the display model you are
installing.
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
1321 S. State College Blvd., Fullerton, CA 92831 USA
1. Swipe GAPit along vertical gap
2. Inspect for .050” gap & adjust if
needed
3. Swipe GAPit along horizontal
gap
4. Inspect for .050” gap & adjust if
needed
9589-000-002-00 Rev.1
Use the GAPit GO/No Go Gauge as a final step in the process to inspect and adjust the gap to
prevent costly replacement and extend the lifespan of the displays. For more information,
please visit: www.mounts.com
Damage happens when weight is transferred to the ultra-thin bezels
of video wall installations, if the recommended gap specications of
.050” is not maintained vertically and horizontally. This results in
image distortion, and costly repairs and replacement.
  • Page 1 1
  • Page 2 2

Premier Mounts LMV-405 Installation guide

Premier Mounts
Brand
Premier Mounts
Model
LMV-405
Category
Flat panel accessories
Type
Installation guide
This manual is also suitable for

Premier Mounts LMV-405 is a flat-panel spacer engineered to significantly reduce installation time for large video walls. It is model-specific, designed to work seamlessly with most flat panels.

The LMV-405 allows for the installation of multiple LMV mounts using a single spacer. Simply repeat the installation process for each surrounding LMV mount, using the same spacer for each 2x2 installation or as many times as needed to complete an unlimited LMV large matrix video wall.

To ensure proper alignment, the spacer should be plumb and level before marking the corners where the LMV will be mounted. It is recommended to start from the bottom corner and work upwards. Install the second mount in a horizontal direction, ensuring it remains plumb and level, and repeat this step for each mount horizontally.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents