V-ZUG 990: Experience the epitome of kitchen convenience with our cutting-edge range hood. This versatile appliance operates in both extracted air and recirculation modes, ensuring a fresh and purified cooking environment. With its sleek design, powerful performance, and user-friendly features, the V-ZUG 990 is the perfect choice for modern kitchens.
V-ZUG 990: Experience the epitome of kitchen convenience with our cutting-edge range hood. This versatile appliance operates in both extracted air and recirculation modes, ensuring a fresh and purified cooking environment. With its sleek design, powerful performance, and user-friendly features, the V-ZUG 990 is the perfect choice for modern kitchens.
Installation instructions
Range hood DW-L9
Wall hood
Operating modes: extracted air/recirculation air
J990.113-1
22.3.11 ITH
1
These installation instructions apply to the model: 990 (DW-L9, construction width 90 cm)
Identification plate
➤ Remove the grease filter. The identification plate is located on the inside of the appliance.
Supplied installation accessories
All fixing elements are contained in the scope of delivery.
Extraction mode
➤ Refer to the identification plate for specifications for the required mains voltage, current type and fuses.
➤ Application height of the appliance: up to max. 2000 m above sea level
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Validity
General notes
With the simultaneous operation of firing (e.g. wood, gas, oil or coal-fired heating systems), safe operation is only possible
providing a room negative pressure of 4 Pa (0.04 mbar) is not exceeded at the location of the appliance. Risk of toxic fumes!
An adequate flow of fresh air must be guaranteed, e.g. via non-closable openings in doors and windows and combined with
ventilation wall bricks for incoming and exhaust air or by other technical means.
If the appliance is installed over hobs, each cooking zone must be fitted with an ignition fuse and the minimum distances (see
DIMENSIONS) must be adhered to.
Efficient repairs can only be guaranteed if it is possible to disconnect the appliance at any time without causing any damage.
The extracted air must not be fed into a chimney which is used for exhausting fumes from appliances burning gas or other fuels.
Always observe the fire regulations.
Electrical connections
Electrical connections must made by trained electricians in accordance with the guidelines and standards for low voltage
installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and
socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching
are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and
fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Old installations should
always be checked.
Installation instructions
Range hood DW-L9
Wall hood
Operating modes: extracted air/recirculation air
J990.113-1
22.3.11 ITH
2
Note
• Avoid routing the exhaust air pipeline to the side through the flue casing.
• Planning features for non-destructive de-installation and maintenance of the appliance:
– Do not route telescopic casing in suspended ceilings.
– Avoid silicon joints between the telescopic casing and the appliance.
– All plastering, plasterboarding, wall papering or painting work is to be carried out prior to installing the appliance.
Installation
1. Stick 3 adhesive strips C to the back of the appliance.
2. If the wall is not perpendicular or is partially covered with tiles: fit 2 spacers D in the
fastening holes at the bottom.
3. Attach paper template to the wall. Drill 2 holes (ø 8 mm) for screws S1 and insert
rawlplugs.
4. Fix angle bracket E with screws S1 (ø 5 × 45 mm) and fit hood.
5. Align the hood with adjusting screws S2 horizontally and adjust the distance to the
back wall using the bracket F.
6. Remove grease filter.
7. In the inside of the hood, mark 2 fastening holes at the bottom for screws S3. Take
down the hood, drill holes (ø 8 mm) and insert rawlplugs. Fit the hood and fix with
screws S3 (ø 5 × 45 mm).
8. Insert grease filter.
Dimensions
Metal ring
Use of stone claddings
20 mm thick wall panels (granite, marble)
are possible.
* With metal ring: 805 mm
Telescopic casing
(available in various heights)
Distance above hob
Minimum height B:
Height A:
➤ see planning documents
for kitchen appliances
For electric hob:
For gas hob:
min. 300 mm
min. 400 mm
Installation
170
30
160
240
250
ø 150
765 *
62
6
900
AB
724.7
~1025
290
750
352
309
80
ø 150
60
40
20
S1
E
F
S3
C
D
S2
Installation instructions
Range hood DW-L9
Wall hood
Operating modes: extracted air/recirculation air
J990.113-1
22.3.11 ITH
3
Extraction mode and recirculation mode with telescopic casing:
➤ Fix seal G and exhaust air connection H using 2 screws S4 (ø 3.5 × 9.5 mm).
➤ Insert cover plate J.
➤ Drill 2 holes for screws S5 – aligned with appliance – in the wall under the ceiling and insert plugs.
➤ Fix metal support K (for flue) with screws S5 (ø 5 × 45 mm).
➤ Only for recirculation mode:
Screw diverter piece L with 2 screws S6 (ø 2.9 × 6.5 mm) to metal support K.
➤ Fix metal ring R to exhaust air connection H and mount exhaust air hose. Ensure hose is free from
kinks and is stretched.
➤ Install lagging sheets V1, V2. Fix upper lagging sheet V1 with 2 screws S7 (ø 3 × 9 mm) to metal
support K.
Recirculation mode without telescopic casing:
➤ Fasten the air outlet grille M – direction facing forwards – instead of exhaust air connection H,
using 2 screws (ø 3.5 × 9.5 mm).
➤ Insert cover plate J.
S4 S4
R
H
G
M
J
V1
V2
L
V1
V2
K
S7
S6
S5
-
1
-
2
-
3
V-ZUG 990: Experience the epitome of kitchen convenience with our cutting-edge range hood. This versatile appliance operates in both extracted air and recirculation modes, ensuring a fresh and purified cooking environment. With its sleek design, powerful performance, and user-friendly features, the V-ZUG 990 is the perfect choice for modern kitchens.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
ferm LIVING Haze Wall Cabinet Assembly Manual
-
Electrolux EFA90245X User manual
-
Baumatic BCD70 User manual
-
Baumatic BT13.1SS User manual
-
Zanussi ZHC605X User manual
-
Miele DA 5495 W Datasheet
-
-
Miele DA 396-5 Datasheet
-
Baumatic STD6.2SS - 39992087 User manual
-
Zanussi ZHC94X User manual
