Hit-N-Hitch 8581316 Owner's manual

Type
Owner's manual

This manual is also suitable for

Hit-N-Hitch 8581316 is a 12 TON “Adjustable” Slide Mount for a 2” Receiver with 4 bolts that provide a clamp load of 48,000 lbs. For height adjustment, simply loosen the 4 bolts and slide to the required height.

Hit-N-Hitch 8581316 is a 12 TON “Adjustable” Slide Mount for a 2” Receiver with 4 bolts that provide a clamp load of 48,000 lbs. For height adjustment, simply loosen the 4 bolts and slide to the required height.

INTRODUCES
AUTOMATIC ON ROAD
HITCHING SYSTEM
“World’s Largest Supplier of
Tractor-Implement Drawbar
Hitching Components”
HIT-N-HITCH PRODUCT LINE
Power Pin Part: #ASMB12TBA
Description: 12 TON “Adjustable” Slide Mount for a 2”
Receiver with 4 bolts that provide a clamp load of 48,000 lbs.
* For height adjustment, simply loosen the 4 bolts and slide
to the required height.
Power Pin Part: #ASMB15TBA
Description: 15 TON “Adjustable” Slide Mount for a 2-1/2”
Receiver - for new 3/4 and 1 TON Trucks
Power Pin Part: #CM12TWPA
Description: 12 TON Clevis Mounting Bracket, comes with 1”drawpin and can
easily be mounted to the 12 TON Adj. Slide Mount Receiver, P/N ASMB12TBA
* Off the shelf trailer balls can easily be installed into the mounting
bracket when not using the drawpin (trailer ball not included).
* “Farmer’s Hitch” for pulling farm equipment with a ring or clevis.
Power Pin Part: #TDH2
Description: Truck Drawbar Holder
The Holder height adjusts from 15” - 20” tting in most Pickup Trucks.
* Holder mounts to the box rail by using the clamping plate supplied.
* The 2 Holder pockets are for your standard 2”x 2” Receiver hitch.
* Safe, Convenient storage for truck drawbars.
Power Pin Part: #TDC72A
Description: 14,000 lb. Truck Drawbar with 2” Drop
* Stops and aligns truck hitch for easier hitching
* Comes with Chain Supports
* Trailer Ball not included
Power Pin Part: #TDC74A
Description: 14,000 lb. Truck Drawbar with 4” Standard Drop
with optional spacer to accommodate a 2” Drop
* Additionally a 2-5/16” and a 2” Trailer Ball can be used in combination
* Trailer Balls not included
Trailer Ring Hitches
Trailer Ball Hitches & Bracket
Power Pin Part: #HM131
Description: 6 Hole Adjustable mount
bracket c/w 5/8” dia. Mounting holes
Rating: 4,400 lbs. Max Vertical Load
22,000 lbs. Max Gross Trailer Wt.
Power Pin Part: #TBH14A
Description: “Automatic” locking
trailer ball Hitch - 2-5/16” Ball.
Rating: 2,100 lbs. Max Vertical Load
14,000 lbs. Max Gross Trailer Wt.
Power Pin Part: #HH10TVR
Description: 12.5 TON - 2 Hole Vertical Mount
* Turn the Ring Hitch over for height
adjustment
* Optional “Lock Assembly” feature
(HM64A)
Power Pin Part: #HH20TV
AN INDUSTRY FIRST
Description: 20 TON – 3 Hole Vertical Mount
* Turn the Ring Hitch over for
height adjustment.
* Optional “Lock Assembly”
feature (HM64A)
Power Pin Part: #HH30TH
Description: 30 TON – 4 Hole Horizontal Mount
* Optional “Lock Assembly” feature
(HM78A)
Power Pin Part: #HM64A
Description: Optional “Lock Assembly”
for the 12.5 TON and the 20 TON Ring
Hitch. An off the shelf padlock is
required to secure the lock assembly.
Zinc Plated
Power Pin Part: #HM78A
Description: Optional “Lock
Assembly” for 30 TON Ring Hitch only.
An o the shelf padlock required to
secure the lock assembly. Zinc Plated
Power Pin Part: #TBH20A
Description: “Automatic” locking
trailer ball Hitch - 2-5/16” Ball.
Rating: 4,400 lbs. Max Vertical Load
22,000 lbs. Max Gross Trailer Weight
TRAILER HITCHES
TRUCK ACCESSORIES
Printed in Canada
Gary LaRocque
General Manager
Phone: (306) 331-0434
www.powerpin.ca
Meets SAE Standards
Patents Pending
Patents Pending
Patent Pending
INDUSTRY FIRST
TRAILER RING HITCH with OPTIONAL LOCK
* An Industry rst for on-road, offset 3 hole,
20 TON ring hitch
* Offset holes provide additional height adjustment
when the ring hitch is turned over.
* Integral trailer LOCK is built into the ring design
and can always be with the ring hitch using an
off the shelf padlock.
BALL / RING COMBO TRUCK HITCH
* Back plate helps to position the trailer ball or
ring hitch for easier hook-up and helps to remove
the annoying slap in the ring hitch connection.
* Primary “automatic” ring lock, plus a secondary
manual lock
* Comes with Intermediate Safety Chain Supports.
INTERMEDIATE SAFETY CHAIN SUPPORTS
* Keep your safety chains from dragging
ADJUSTABLE TRUCK TUBE
* Slotted adjustable holes allows operator to adjust
the height easily when loosening the 4 bolts and
sliding to the required height and then re-tighten
the bolts. Each bolt provides 12,200 lbs. of clamp
load equaling over 48,000 lbs. of total clamp load.
This joint will not slide when
properly tightened.
* The design of the adjustable tube provides the
operator with various bolt on options of the
Hit-N-Hitch Product Line.
“NEW” ON-ROAD HIT-N-HITCH PRODUCT LINE
Power Pin Inc. the Canadian hitching
company that produces approx 250,000
drawbar
hitching components annually for the
AG Equipment Industry,
including the “Drop-Pin”
hammerstrap, is introducing
a new “On-Road” line of
hitches. Power Pin has
drawn on their 25 years of
producing hitches for the
AG Equipment Industry to
design the “Gold Standard”
on-road hitches.
We started the Hit-N-Hitch
on-road product line with
a goal of removing cost,
simplifying design and
adding features.
Ball/Ring Combo Truck Hitch
Automatic Locking Pintle Hitches
Power Pin Part: #PCH7TA
Description: 7 TON “Combo” Ball/Ring
Tube Assembly comes with 2” Ball
* An optional 2-5/6” Ball can be purchased (p/n HM105A)
Rating: 2,800 lbs. Max. Vertical Load
4,000 lbs. Max. GTW
Power Pin Part: #PCH7T16A
Description: 7 TON “Combo” Ball/Ring
Tube Assembly comes with 2-5/16” Ball
* An optional 2” Ball can be purchased (p/n HM106A)
Rating: 2,800 lbs. Max. Vertical Load
14,000 lbs. Max. GTW
Power Pin Part: #PCH10TFA
Description: 15 TON “Combo” Ball/Ring
Flat Mount comes with a 2-5/16” trailer ball.
This pintle can be mounted onto:
12 TON Adj. Slide Mount Receiver, p/n ASMB12TBA or
15 TON Adj. Slide Mount Receiver, p/n ASMB15TBA.
A 2” trailer ball can be purchased as an option p/n HM106A
Rating: 4,000 lbs. Max Vertical Load
20,000 lbs. Max GTW
Power Pin Part: #HNH7TA
Description: 7 TON Pintle Tube Assembly
Rating: 2,800 lbs. Max. Vertical Load
14,000 lbs. Max. Gross Trailer Weight
Power Pin Part: #HNH25TFA
Description: 25 TON Flat Mount Pintle
Rating: 10,000 lbs. Max Vertical Load
50,000 lbs. Max. Gross Trailer Weight
Power Pin Part: # HNH12TFA
Description: 15 TON Flat Mount Pintle.
Product can easily be mounted to the
12 TON Adj. Slide Mount Receiver, p/n ASMB12TBA
or 15 TON Adj. Slide Mount Receiver, p/n ASMB15TBA
Rating: 4,800 lbs. Max Vertical Load
24,000 lbs Max Gross Trailer Weight
TRUCK HITCHES
Patent Pending
Patent Pending
Patents Pending
  • Page 1 1
  • Page 2 2

Hit-N-Hitch 8581316 Owner's manual

Type
Owner's manual
This manual is also suitable for

Hit-N-Hitch 8581316 is a 12 TON “Adjustable” Slide Mount for a 2” Receiver with 4 bolts that provide a clamp load of 48,000 lbs. For height adjustment, simply loosen the 4 bolts and slide to the required height.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI