Andersen Big Doors, MultiGlide Door Service Instructions

Type
Service Instructions
Thank you for choosing Andersen.
· Product Series - Big Doors
· Product Type - MultiGlide™ Door
Andersen” and all other marks where denoted are trademarks of Andersen Corporation. ©2017 Andersen Corporation. All rights reserved. REPLACEMENT 9151901 BA 11/16/2017
Read these instructions and the Product Safety
Information before starting procedure.
Roller Replacement
Instructions for:
Parts Included
(1) - Roller
Assembly
(2) - #8 x 1"
Phillips Head
Screw
(2) - Roller
Assembly Spacer
(On-Floor Drainage Sill Only)
Safety Information
WARNING
· Windows and doors can be heavy. Use safe lifting
techniques and a reasonable number of people with
enough strength to lift, carry, and install window and
door products. Heavier windows and doors will require
mechanical assistance. Failure to do so could result in
injury, product or property damage.
WARNING
· Follow manufacturers’ instructions for hand and power
tools. Always wear safety glasses. Failure to do so could
result in injury, product or property damage.
Safety
Glasses
Tools and Supplies Needed
Thin Blade
Putty Knife
#2 Phillips Head
Screwdriver
Caulk Gun
and Sealant
WARNING
· Windows and doors have small parts (e.g. hole plugs,
operator spline caps, fasteners, etc.). Small parts if
swallowed could pose a choking hazard to young
children. Dispose of unused, loose, or easily removed
small parts. Failure to do so could result in injury.
Draft
2
Fig. 1 Fig. 2
With Flush Sill
A
E
B
1. Remove the panel with the damaged roller.
2. Remove the roller stabilizing clips and save for reuse.
3. Remove the bottom rail ller and save for reuse
4. Remove the damaged roller assembly and dispose of properly.
5. Position and fasten the new roller assembly.
6. Remove adhesive tape residue from the bottom rail ller and bottom of panel. (Fig. 1)
7. Apply two (2) 1/8" beads of sealant, full length to the bottom rail ller. (Fig. 2)
8. Reposition the bottom rail ller and fasten.
9. Reattach the roller stabilizing clips and fasten.
10. Reinstall the Panel.
Roller replacement is complete.
A - Door Panel
B - Roller Assembly
C - Sealant
D - Bottom Rail Filler
E - Roller Stabilizing Clips
D
CSealant
Beads
Clean bottom of panel
and bottom rail ller
as shown
A
D
D
Draft
3
Slide roller spacers
onto roller assembly
as shown
1. Remove the panel with the damaged roller.
2. Remove the bottom rail ller and save for reuse.
3. Remove the damaged roller assembly and dispose
of properly.
4. Position the roller spacers on the new
roller assembly. (Fig. 1)
5. Position and fasten the new roller assembly.
6. Remove adhesive tape residue from
the bottom rail ller and bottom of panel. (Fig. 2)
7. Apply two (2) 1/8" beads of sealant,
full length to the bottom rail ller.(Fig. 3)
8. Reposition the bottom rail ller and fasten.
9. Reinstall the panel.
Roller replacement is complete.
A
D
B
A - Door Panel
B - Roller Assembly
C - Sealant
D - Bottom Rail Filler
E - Roller Spacers
BE
With On-Floor Drainage Sill
E
D
A
Clean bottom of panel
and bottom rail ller
as shown
D
C
Sealant
Beads
Fig. 1
Fig. 2 Fig. 3
  • Page 1 1
  • Page 2 2
  • Page 3 3

Andersen Big Doors, MultiGlide Door Service Instructions

Type
Service Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI