Marantec EM 184 Owner's manual

Brand: Marantec

Model: EM 184

Type: Owner's manual

Expansion module EM 184

Draw-in protection MSBUS

XW41C

XW41A

LED 4

LED 3

LED 2

LED 1

24V DOWN

E F

DIP

12V UP

ES MODUL

XP16A XP16B

GN GN

BN BN

WH WH

Manual for installation and operation

2 Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543)

2. Table of contents

Caution!

Danger of personal injury!

The following safety advice must be

observed at all times so as to avoid

personal injury!

Attention!

Danger of material damage!

The following safety advice must be

observed at all times so as to avoid

material damage!

Advice / Tip

Check

Reference

Advice

1. Meaning of symbols . . . . . . . . . .2

2. Table of contents . . . . . . . . . . . .2

3. General safety advice . . . . . . . . .3

4. Product overview . . . . . . . . . . . .5

5. Installation . . . . . . . . . . . . . . . . .5

5.1 Install expansion module . . . . .5

5.2 Wiring of the expansion

module . . . . . . . . . . . . . . . . . .6

6. Initial operation . . . . . . . . . . . .10

7. Appendix . . . . . . . . . . . . . . . . . .11

1. Meaning of symbols

Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543) 3

3. General safety advice

Target group

This operator system may only be installed, connected and put into operation by qualified and trained

professionals!

Qualified and trained specialist personnel are persons

- who have knowledge of the general and special safety regulations,

- who have knowledge of the relevant electro-technical regulations,

- with training in the use and maintenance of suitable safety equipment,

- who are sufficiently trained and supervised by qualified electricians,

- who are able to recognise the particular hazards involved when working with electricity,

- with knowledge regarding applications of the EN 12635 standard (installation and usage requirements).

Warranty

For an operations and safety warranty, the advice in this instruction manual has to be observed.

Disregarding these warnings may lead to personal injury or material damage. If this advice is disregarded,

the manufacturer will not be liable for damages that might occur.

To avoid installation errors and damage to the device, it is imperative that the installation instructions are

followed. The product may only be operated after reading these installation and operating instructions.

The installation and operating instructions are to be given to the door system user, who must keep them

safe. They contain important advice for operation, checks and maintenance.

This item is produced according to the directives and standards mentioned in the Manufacturer's

Declaration and in the Declaration of Conformity. The product has left the factory in perfect condition with

regard to safety.

Power-operated windows, doors and gates must be checked by an expert (and this must be documented)

before they are put into operation and thereafter as required, but at least once a year.

Correct use

The extension module expands a control unit with MSBUS.

Beside the advice in these instructions, please observe the general safety and accident

prevention regulations! Our sales and supply terms and conditions are effective.

Please read carefully!

3. General safety advice

Installation tips

• Ensure that the devices to be connected (doors etc.) are in a mechanically faultless state.

• Before commencing cabling works it is very important to disconnect the system from the electricity supply.

Ensure that the electricity supply remains disconnected throughout the cabling works.

• Adhere to the local protection regulations.

• Lay the electricity supply cables and control cables; these MUST be laid separately.

The operating voltage is 24 V.

Information on cleaning the operator system

Never use water jets, high pressure cleaners, acids or bases for cleaning.

Please read carefully!

4 Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543)

Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543) 5

XW41A

LED 4

LED 3

LED 2

LED 1

ES MODUL

XW41C

XP16A XP16B

GN GN

BN BN

WH WH

24V DOWN

E F DIP

12V UP

Supply package

Dimensions

1 Expansion module

2 MSBUS cable

3 System cable coded

4 Manual for installation and operation

4 / 1

XW41A

LED 4

LED 3

LED 2

LED 1

ES MODUL

XW41C

XP16A XP16B

GN GN

BN BN

WH WH

24V DOWN

E F DIP

12V UP

4 / 2

126

5.1 Install expansion module

5. Installation

• Fit the expansion module (B) to the DIN rail (A).

4. Product overview

XW41C

XW41A

LED 4

LED 3

LED 2

LED 1

24V DOWN

E F DIP

12V UP

ES MODUL

XP16A XP16B

GN GN

BN BN

WH WH

5.1 / 1

XW41B

XW41C

XW41A

LED 4

LED 3

LED 2

LED 1

XP16A XP16B

GNGN

BN BN

WHWH

24V DOWN

EF DIP

12V UP

OFF

5. Installation

6 Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543)

Label Type / function

Operating indicator

Light on .......... In operation

B Draw-in protection XP16A

C Draw-in protection testing

D Draw-in protection XP16B

E Dip switch DIP E

F Dip switch DIP F

XP16A Draw-in protection 1

XP16B Draw-in protection 2

XW41A MSBUS connection

XW41B MSBUS connection

XW41C MSBUS connection

5.2 Wiring of the expansion

module

5.2.1 Overview of the module connections

B, C, D:

Light flashes

.......... Cable break

Single flash (run light)

...scanning MSBUS

5.2.1 / 1

XW41A

XP16B

XP16A

XW41CXW41B

Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543) 7

5. Installation

Attention!

To ensure correct operation, only the

MSBUS system must be used.

5.2.2 Connection of the modules

• Connect the MS bus control unit to the

connecting socket XW41A or XW41B.

• Connect further modules to socket XW41C as

required.

Connection of the control unit and a further

module

DIP E Function

OFF

Draw-in protection 12V

(factory setting)

ON Draw-in protection 24V

DIP F Function

OFF

Both draw-in protection devices

work in the OPENING direction

Both draw-in protection devices

work in the CLOSING direction

DIP switch (E) settings

DIP switch (F) settings

XW41B

XW41C

DOWN

OFF

XW41B

XW41C

5.2.2 / 1

XW41A

8 Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543)

5. Installation

Anschluss Einzugssicherung dynamisch

5.2.2 / 3

M14E006

Label Type / function

BP29A Draw-in protection, receiver RX

BP29B Draw-in protection, transmitter TX

DIP E Function

OFF Draw-in protection 12V

DIP switch (E) settings

Connection for draw-in protection tested

Label Type / function

BP30A Draw-in protection, receiver RX

BP30B Draw-in protection, transmitter TX

X1 Terminal

5.2.2 / 2

M14E006

DIP E Function

OFF Draw-in protection 12V

ON Draw-in protection 24V

DIP switch (E) settings

Attention!

Selecting the wrong voltage will

destroy the photocell.

Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543) 9

Connection for draw-in protection with relay

5.2.2 / 4

M14E006

Label Type / function

BP31A Draw-in protection, receiver RX

BP31B Draw-in protection, transmitter TX

DIP E Function

ON Draw-in protection 24V

DIP switch (E) settings

5. Installation

Assignment of terminals

I –> Test signal for draw-in protection

GN Signal of draw-in protection

+ 24V / +12V DC,

depending on DIP switch E

WH GND

Key to cable colours

BN brown

GN green

WH white

YE yellow

10 Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543)

After connecting the control unit, the LED

displays (B, C, D) flashes slowly (Module not

connected to MSBUS).

• The module will be recognised automatically by

the control during initial use.

The control unit requires approx. 30 seconds to

recognise any modules connected to it.

The module reset ends automatically

(run light display B, C, D – MSBUS module

recognised).

A Operating indicator

B Draw-in protection photocell (EZS) 1

connected

C Draw-in protection testing (EZS)

D Draw-in protection photocell (EZS) 2

connected

6. Initial operation

Advice:

The draw-in protection must be

connected up before initial use.

Possible draw-in protection:

- Three-wire draw-in protection,

- Four-wire draw-in protection with

testing, or

- Draw-in protection with relay

XW41B

XW41C

XW41A

LED 4

LED 3

LED 2

LED 1

XP16A XP16B

GN GN

BN BN

WH WH

24V DOWN

EF DIP

12V UP

6 / 1

Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543) 11

7. Appendix

Technical data

Operating

voltage

V 24 to 30

Max. draw-in

protection

current

mA 200

Protection

Marantec EM 184 Owner's manual

Marantec EM 184 Owner's manual

Marantec EM 184 Owner's manual

Related papers

Other documents