Premier SCR-4329DUSD User manual

Premier
Brand
Premier
Model
SCR-4329DUSD
Category
Car media receivers
Type
User manual
MPEG4/MP3/USB/MMC/DVD RECEIVER
SCR-4329DUSD
CAR-AUDIO WITH USB/SD PLAYER
DVD,MPEG4*,AVI*,VCD,MP3,WMA,CD Operation
NOTES ON INSTALLATION
01
02
03
MPEG4*/AVI*
AVI
PRECAUTIONS
CONTROL LOCATIONS RECEIVER
MPEG4/MP3/USB/MMC/DVD RECEIVER
Reset Button
Power Button
Volume/SEL Button
AUX IN Socket
Mute Button
Time-Display/Adjustment
Remote Control Sensor
Up Button / 10+
Down Button / 10-
Play/Pause/AMS Button
Tuning/Selecting Ttacks
MOD Button
CD Slot
LCD Display
Relaease Button
Disc Lamp
Eject Button
USB Socket
20
20
SD/MMC socket
04
DVD,MPEG4*,AVI*,VCD(1.0,2.0),
SPECIFICATION
25
Video
ANT
Audio out
FUSE:When replacing the fuse,make sure that the new fuse is the correct type
and amperage.Using an incorrect fuse could damage the unit.
ADDITIONAL INFORMATIONS
WIRING CONNECTION DIAGRAM
This unit uses 10 amp Fuse for Memorhy Back up.
0524
USING THE DETACHABLE FRONT PANEL
The notch A(shown as picture)should be put onto shaft B.and then slightly
press into the left side
DETACHING & REMOVING THE FRONT PANEL
Press Release button(16)in the upper right corner,the front panel will be
folded down.
When the front panel isfolded dowm,hold and slide the front panel to right-
side,and pulling it out.
Note:For safekeeping,store the front panel in the supplied protective case immediately after
being removed
UNIT INSTALLATION
Press Power button (2) to turn on the unit.
When the unit is on,press Power button (2) to turn
off the unit.
Press Release button (16) to detach the removable
font panel.
Repeatedly press SEL button (3) toselect between
Volume(default),Bass,Treble,Balance and Fader
mode in followqing order:
Rotate VOL knob (3) to desired level of selected mode.
Rotate VOL knob (3) to desired sound level
Press SEL button (3) until “BAS” appears on display
Rotate VOL knob(3) to desired bass level
Press SEL button (3) until “TRE” appears on display.
Press VOL button (3) to desired treble level
Press SEL button (3) until “BAL” appears on display.
Rotate VOL knob(3) to desired balance level between
left and right speakers.
Press SEL button (3) until “FAD” appears on display.
Rotate VOL knob(3) to desired balance level between
front & rear speakers.
Press SEL button (3) until “LOUD” appears on display
Rotate VOL knob(3) to turn on or off the loudneess function.
Press SEL button (3)until “DSP” appears on display.
Rotate VOL knob (3)to desired audio mode. There are
5 kins of mode display in following:
Press SEL button (3)until “STERO” apperas on display.
Rotate VOL knob (3) to select ST or MONO function.
GENERAL OPERATIONS
ON/OFF
FRONT PANEL RELEASE
AUDIO Setting
VOLUME
BASS
TREBLE
BALANCE
FADER
LOUD
DSP
STEREO
06
UNIT INSTALLATION
23
Press SEL button (3) to until “LOC” appears on display.
Rotate VOL knob (3) to turn on or off the loc function.
During radio mode, press and hold SEL Button(3)for
several seconds,frequency area will display in
following order:
Note : Frequency spacing selection available in radio mode ONLY.
While one of the forquency area display on LCD,
Rotate VOL knob (3) to swich to another frequency area.
[eg,USA (American) to EUR (Eurpoean) frequency area]
Individual Volume, Bass,Treble,Balance and Fader
settings are retained in memory for radio, CD(MP3)
and AUX modes.
Note:Volume level is always return to factory default setting each
time the unit is powered on.
Press MUT button (5) to cut down the sound output
“MUTE” blinking on the display, press it again to
release this mode and resume to previous volume level.
Point the remote handset to control the remote sensor
( 7 ).
Press the function keys on the remote handset to control
the system.
The LCD(15)can show the current working state of the
unit.
The LED lamp (17) will flashing if the front panel does
not install in the mail unit or improper installation.
GENERAL OPERATIONS
LOC
FREQUENCY SPACING
SOURCE AUDIO MEMORY
MUTE
REMOTE SENSOR
LCD DISPLAY
FLASHING LED
07
SETUP
22
Press CLK button (6), the current clock time is
displayed, display will returns to previous mode
when mode has not been adjust for 5 seconds.
Press and hold CLK button (6) for several seconds,
until the clock time is blinking,rotate the VOL button
(3) clockwise or anti-clockwise to adjust the hours,
press SEL button (3) to confirm the hours adjustment.
Then, rotate the VOL button (3) clockwise or anti-
clockwise to adjust the minutes. Press SEL button (3)
again for final confirmation.
RESET button (1) is placed on the housing and must
be activated with either a ball point pen or thin
metal object. (DO NOT use sharp object to avoid
damaging the unit.) The RESET button (1) is to be
activated for the following reasons:
- Initial installation of the unit when all wiring is
completed.
-All the function buttons do not operate
-Error symbol on the display
NOTE: If the problem continues to persist after pressed RESET button
(1), it is recommended to use a cotton swab soaked in isopropyl
alcohol to clean pin connector socket on the back of the front
panel.
08
SETUP
21
To enjoy the audio from the SD/MMC card or USB
device, insert the SD/MMC card or USB device into the
SD/MMC socket (20) or USB socket (19), press Source
button(13) to select the mode. The system will playing
the card or device’s contents automatically. Please
refer to the picture as following:
MEMORY CARD OPERATIONS
09
SETUP
is recorded in digital signal.
decode function of in digital signal.
20
With the label facing up, insert a standard size disc into
disc slot (14).
The disc will automatically begin playback.
Press Eject button (18) to stop disc playback and eject
the disc from disc slot (14). The unit will automatically
return to radio mode.
During disc operation, press or (Track) button
(12) to move to the previous or next track. Track number
shows on the display.
Press and hold or (Track) button (12) to fast
reverse or forward the track. Disc play starts from
when you release the button.
Press button (16) temporarily to pause
disc playback. Press it again to resume playback.
Note:REPEAT / INTRO /RANDOM FUNCTION:press the related button on
the remote control
Some CD-Rs and CD-RWs may be incompatible with
this unit depending on media type and recording method.
In addition, the following discs may be incompatible
with this unit.
Discs exposed to extreme high temperatures or direct
sunlight for extended periods of time. Discs recorded in
which recording sessions failed or re-recording was
attempted and, or encrypted or copy-protected.
Discs which do not conform to the audio CD-DA red book
recording Standard.
Note: Disc standard size: diameter: 12cm , thinkness:1.2mm
CD OPERATIONS
INSERT DISC
EJECT DISC
TRACK SELECTION
FAST FORWARD
AND REVERSE
PAUSE PLAYING
CD-R/CD-RW
COMPATIBILITY
While listening to (or watching) DVD, MPEG4*,AVI*,
VCD, MP3, WMA, CD, just insert a Disc (with labeled side
up) into the Disc slot (12), the mechanism will automatically
switch on. While it is Radio / AUX mode and a Disc was
loaded, press MOD button (11) to paly the Disc.
NOTE: For MOD function, refer to Page 10 for details. Disc icon
will be shown on LCD if a disc was loaded.
During playing mode, press or (Track) button
(10) to move to the previous or next track. Track
number shows on the display.
Press and hold or button (Track) (10) to fast
rewind or fast forward the track. Track play starts
from when vou release the button.
TRACK SELECTION
FAST FORWARD AND
FAST REVERSE
DVD,MPEG4*,AVI*,VCD,MP3,WMA,CD OPERATION
11
SETUP
18
MIXED FILE FORMAT DISC*
12
SETUP
17
REMOTE CONTROL LAYOUT
13
REMOTE CONTROL OPERATION
16
REMOTE CONTROL OPERATION
1514
REMOTE CONTROL OPERATION
REMOTE CONTROL OPERATION
1514
REMOTE CONTROL OPERATION
REMOTE CONTROL LAYOUT
13
REMOTE CONTROL OPERATION
16
MIXED FILE FORMAT DISC*
12
SETUP
17
With the label facing up, insert a standard size disc into
disc slot (14).
The disc will automatically begin playback.
Press Eject button (18) to stop disc playback and eject
the disc from disc slot (14). The unit will automatically
return to radio mode.
During disc operation, press or (Track) button
(12) to move to the previous or next track. Track number
shows on the display.
Press and hold or (Track) button (12) to fast
reverse or forward the track. Disc play starts from
when you release the button.
Press button (16) temporarily to pause
disc playback. Press it again to resume playback.
Note:REPEAT / INTRO /RANDOM FUNCTION:press the related button on
the remote control
Some CD-Rs and CD-RWs may be incompatible with
this unit depending on media type and recording method.
In addition, the following discs may be incompatible
with this unit.
Discs exposed to extreme high temperatures or direct
sunlight for extended periods of time. Discs recorded in
which recording sessions failed or re-recording was
attempted and, or encrypted or copy-protected.
Discs which do not conform to the audio CD-DA red book
recording Standard.
Note: Disc standard size: diameter: 12cm , thinkness:1.2mm
CD OPERATIONS
INSERT DISC
EJECT DISC
TRACK SELECTION
FAST FORWARD
AND REVERSE
PAUSE PLAYING
CD-R/CD-RW
COMPATIBILITY
While listening to (or watching) DVD, MPEG4*,AVI*,
VCD, MP3, WMA, CD, just insert a Disc (with labeled side
up) into the Disc slot (12), the mechanism will automatically
switch on. While it is Radio / AUX mode and a Disc was
loaded, press MOD button (11) to paly the Disc.
NOTE: For MOD function, refer to Page 10 for details. Disc icon
will be shown on LCD if a disc was loaded.
During playing mode, press or (Track) button
(10) to move to the previous or next track. Track
number shows on the display.
Press and hold or button (Track) (10) to fast
rewind or fast forward the track. Track play starts
from when vou release the button.
TRACK SELECTION
FAST FORWARD AND
FAST REVERSE
DVD,MPEG4*,AVI*,VCD,MP3,WMA,CD OPERATION
11
SETUP
18
Note:During Disc operation,press the button(8)to skip forward 10 songs or
press the button(9)to skip back 10 song.Skip tracks,repert,random and
play the first track functions are also available for Mp3 palyback
During radio mode, press BND button (11) to select
the desired band. Repeatedly press the BND button
(11), the reception band will be change in following
order:
Press SEL button(3) until “LOC” appears on display.
Then press VOL button(3) to turn on or turn off
the loc funcion.
LOC ON(local station):local setting for reception of
strong station.
LOC OFF(distant station):distant setting for receiption
of weaker station.
Note:This function is available in FM band only.
Press SEL button(3) until “STERO” appears on display.
Then press VOL button(3) to select ST or MONO function.
you can sometimes improve reception of distant station
by selection mono operation.
Press and hold ( ) to activate automatically memory
storing function.
Scanning stations manual:press button(12)shortly
to scan station upward or downward.
Scanning stations antomatically:press button(12)
for more than 3 second to active automatically scan
store.press upward button(8) or downward button(9)
to select any one of stored station in the current band.
TUNNING/SELECTING
BAND SELECTION
LOCAL/DISTANCE
MONO/STEREO
RADIO OPERATION
During the payback mode,press BAND/SYS key(11)to AUTO,PAL OR NTSC system.
10
SETUP
19
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26

Premier SCR-4329DUSD User manual

Premier
Brand
Premier
Model
SCR-4329DUSD
Category
Car media receivers
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents