Hotpoint HTDX100GM0WW Installation guide

Brand: Hotpoint

Model: HTDX100GM0WW

Type: Installation guide

Installation

Instructions

Gas Drger

Questions on installation? Call: 1-800-GECARES (US)

or Visit ou r Web site at: www.GEAppliances.com (US)

BEFOREYOU BEGIN

Read these instructions completely and

carefully.

•IMPORTANT- Save these instructions for

local inspector's use.

•IMPORTANT- Observe all governing codes

and ordinances.

• Noteto Installer - Besureto leavethese

instructionswith thecustomer.

• Note to Customer - Keep these instructions

with gour Use and Care Book for future

reference.

• Before the old drger is removed from service or

discarded, remove the drger door.

• Inspect the drger exhaust outlet and straighten

the outlet walls if theg are bent.

• Service information and the wiring diagram

are located in the control console.

• Do notallow children on or inthe appliance.

Close supervisionof children is necessarg when

the applianceis used near children.

• Install the drgerwhere the temperatureis

aboveSO°Ffor satisfactorg operationof the

drger controlsgstem.

WARNING RBKOFFIRE

Toreducethe riskof severeinjurgor death,followall installation instructions.

Clothesdrger installationmustbeperformedbg aqualified installer.

Installthe clothesdrger accordingtotheseinstructionsand in accordancewith local

codes.Inthe absenceof localcodes,installationmust comptgwith NationalFuelGas

Code,ANSIZ225.1/NFPA54or the CanadianNaturalGasand PropaneInstallationCode,

CSAB149.1.

ColifomioSafeDrinkingWaterond ToxicEnforcementAct.

Thisact requiresthe governorof Californiato publisha listof substancesknownto the

stateto causecancer,birth defectsor otherreproductiveharm andrequiresbusinesses

to warn customersof potential exposureto suchsubstances.Gasappliancescan

causeminorexposuretofour of thesesubstances,namelg benzene,carbonmonoxide,

formaldehgdeand soot,causedprimaritgbgthe incompletecombustion of naturalgas

or LPfuels.Properlgadjusted drgerswiltminimizeincompletecombustion.Exposure

to thesesubstancescan be minimizedfurther bg properlgventingthe drger to the

outdoors.

Thisdrger must beexhaustedto the outdoors.

Useonlg4" rigid metalducting forexhaustingthe clothesdrger to the outdoors.

DONOTinstall aclothesdrger with flexibleplasticducting materials.Ifflexible metal

(semi-rigidor foit-tgpe)duct isinstalled,it mustbe ULlistedand installedinaccordance

with the instructionsfound in "ConnectingTheDrgerToHouseVent"on page6ofthis

manual.Flexibleventing materialsare knownto collapse,beeasilgcrushed,andtrap

lint.Theseconditionswiltobstructdrger airflow andincreasethe riskoffire.

Donot installor storethisappliance in anglocationwhereit couldbeexposedto water

andor weather.

Drgersinstalledin residentialgaragesmustbeelevated 18"(46cm)abovethe floor.

Savetheseinstructions.(Installers:Besureto leavetheseinstructionswith the

customer).

in the state of Massachusetts,installation must be performed bya qualifiedor

licensedcontractor, plumber, or gasfitter qualified or licensedby the state.

TOOLSYOU

WILLNEED

(x2)

IO"ADJUSTABLEWRENCHES _.

8"PIPEWRENCH LEVEL

SLIPJOINTPLIERS FLATBLADESCREWDRIVER

MATERIALSYOUWILLNEED

4"DIA.METALDUCT I====_

(RECOMMENDED)

4"DIAMMETALELBOW

4"DIA.FLEXIBLEMETAL(SEMI-RIGID)

ULLISTEDTRANSITIONDUCT

(IFNEEDED)

KITWXO8X10077(INCLUDES2ELBOWS) 4"DUCTCLAMPS

4"SPRINGCLAMPS

4"DIA.FLEXIBLEMETAL(FOILTYPE) _(x2)

ULLISTEDTRANSITIONDUCT

(IFNEEDED.)

PIPE

EXHAUSTHOOD COMPOUND

DUCTTAPE

FLEXIBLEGASLINECONNECTOR

SOAPSOLUTION

FORLEAKDETECTION

SAFETYGLASSES

GLOVES

Step 1

Step 2

Step 3

Verifg Your Gas Installation (seesection 2).

Prepare the Area and Exhaust for Installation of

New Drger (seesection 1).

Check and Insure the Existing External Exhaust

is Clean (seesection 1)and Meets Attached

Installation Specifications (seesection 6).

Step 4 Remove the Foam Shipping Pads(seesection 1).

Step 5 Move the Drger to the Desired Location.

Step 6 LevelYour Drger (seesection 8).

Step 7 Connect the Gas Supplg (seesection 3) and check

for leaks (seesection 4).

Step 8 Connect the External Exhaust (seesection 7).

Step 9 Connect the Power Supplg (seesection 5).

Step 10 Check the Operation of the Power Supplg, Gas

Connections, and Venting.

Step 11 Place the Owners Manual and the Installation

Instructions in a Location Where Theg Will Be

Noticed Bg the Owner.

For Alcove or Closet Installation see section 9.

For Bathroom or Bedroom Installation see section 10.

For Mobile or Manufactured Home see section 11.

234Dll13PO02 31-16225-1 07/08/10 GE

Installation instructions

Minimum Clearance Other Than Alcove or Closet Installation

Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and 1 in. rear.

Consideration must be given to provide adequate clearance for installation and service.

m PREPARING FOR INSTALLATION

OF NEW DRYER

TIP:Install your dryer before installing your washer.

This will allow better access when installing dryer

exhaust.

DISCONNECTING GAS

TURNGAS

SHUT-0FFVALVE IC?_ DISCONNECTANDDISCARDOLD f}_!/__

j -,_ FLEXIBLEGASCONNECTORAND

TOTHEOFF

POSITION.,,,_ OLDTRANSITIONDUCTING

MATERIAL.REPLACEWITHNEW

CSA(AGA)APPROVEDFLEXIBLE

GASLINECONNECTORANDUL

APPROVEDTRANSITIONDUCT.

WARNING - NEVERREUSEOLD

FLE×IBLE CON NECTORS.

The use of old flexible connectors can cause leaks and

personal iniury. Always use new flexible connectors

when installing gas appliances.

REMOVING LINT FROM WALL

EXHAUST OPENING

, Remove and discard existing plastic or metal foil

transition duct and replace with ULlisted transition

duct.

WALL

INTERNALDUCT

CHECKTHATEXHAUST

OPENING OPENS

ANDCLOSESFREELY.

TILTTHE DRYERSIDEWAYS

AND REMOVETHE FOAM

SHIPPING PADS BY

PULLING AT THE SIDES

AND BREAKING THEM

AWAY FROM THE DRYER

LEGS, BESURE TO

REMOVE ALL OF THE

FOAM PIECESAROUND

THE LEGS.

[] GAS REQUIREMENTS

WARNING

Installation must conform to local codes and

ordinances, or in their absence, the NATIONAL FUEL

GASCODE,ANSI Z223.

This gas dryer is equipped with a Valve & Burner

Assembly for use only with natural gas. Using

conversion kit WE25×0217, your local service

organization can convert this dryer for use with

propane {LP)gas. ALL CONVERSIONSlUST BEMADE BY

PROPERLYTRAINEDAND QUALIFIEDPERSONNELAND

IN ACCORDANCEWITH LOCALCODESAND ORDINANCE

REQUIREMENTS.

The dryer must be disconnected from the gas supply

piping system during any pressure testing of that

system at a test pressure in excess of O.5PSI{3.4 KPa).

The dryer must be isolated from the gas supply piping

system by closing the equipment shut-off valve during

any pressure testing of the gas supply piping of test

pressure equal to or less than 0.5 PSI(3.4 KPa).

DRYER GAS SUPPLY CONNECTION

xc:_ z:E_ j

' 318"NPTHALETHREADGASSUPPLY

NOTE:Addtoverticoldimension

thedistancebetweencobinet

bottomtofloor.

GAS SUPPLY

A 1/8-in.National PipeTaper thread plugged tapping,

accessible for test gauge connection, must be installed

immediatelg upstream of the gas supplg connection to

the drger. Contact sour local gas utilitg should Sou have

questions on the installation of the plugged tapping.

Supplg line isto be 1/2-in. rigid pipe and equipped with an

accessible shut-off within 6 ft. of, and in the same room

with the drger.

Use pipe thread sealer compound or Teflon tape appropri-

ate for natural or LPgas.

You must use with this drger a flexible metal connector

listed connector ANSIZ21.24 / CSA6.10. The length of the

connect shall not exceed 3 ft.

Connect flexible metal connector to drger and gas supplg.

Open shut-off valve.

Installation

_] RECONNECTING GAS

Listed connector ANSI Z2!.24 / CSA 6.!0

1/8" NPTPIPE

NEW METAL PLUG FOR

GAS

FLEXIBLEGAS INLETPRESSURE

LINECONNECTOR

ADAPTER

ELBOW

3/8" NPT

SHUT-OFF

PIPE SIZE

ITEMSNOT SUPPLIED _AT LEAST1/2"

Note: The connector and fittings (]re designed for use

onlg on the original installation and (]re not to be reused

for another appliance or at another location. Keep flare

end of adaptor free of grease, oil and thread sealant.

Caution: Use adapters as shown. Connector nuts must

not be connected directlg to pipe threads.

APPLYPIPECOHPOUND

TOTHEADAPTERAND

DRYERGASINLET.

TIGHTEN THE FLEXIBLE

GAS LINE USING TWO

ADJUSTABLE WRENCHES.

Instructions

APPLYPIPECOMPOUND

TOALL HALETHREADS.

TIGHTEN ALL CONNECTIONS

USINGTWO ADJUSTABLE WRENCHES.

DO NOT OVERTORQUE GAS CONNECTIONS!

[-4]LEAK TEST

"WARNING: NEVERUSEAN OPEN

LAME TO TEST FOR GAS LEAKS.

OPEN

GASVALVE,

Check oil connections for teaks with soopg solution or equivalent.

Apptg soop solution. Leak test solution must not contain ammo-

nia which could cause damage to the brass fittings. If leaks ore

found, close volve, retighten the joint, and repeGt the soap test.

Installation

[-_ ELECTRICAL CONNECTION

INFORMATION

WARNING - TOREDUCETHE

RISK OF FIRE, ELECTRICAL SHOCK,

AND PERSONAL INJURY:

. DO NOT USEAN EXTENSIONCORDORAN ADAPTER

PLUGWITH THISAPPLIANCE.

Dryer must be electrically grounded in accordance

with local codes and ordinances, or in the absence

of local codes, in accordance with the NATIONAL

ELECTRICALCODE,ANSI/NFPANO.70.

ELECTRICAL REQUIREMENTS

This appliance must be supplied with 120V,60Hz, and

connected to a properly grounded branch circuit,

protected by a 15- or 20- amp circuit breaker or time-

delay fuse. If electrical supply provided does not meet the

above specifications, it is recommended that a licensed

electrician install an approved outlet.

,A,WARNING -THISDRYERIS

EQUIPPED A THREE-PRONG (GROUNDING)

PLUG FOR YOUR PROTECTION AGAINST

SHOCK HAZARD AND SHOULD BE PLUGGED

DIRECTLY INTO A PROPERLY GROUNDED

THREE-PRONG RECEPTACLE. DO NOT CUT

OR REMOVE THE GROUNDING PRONG FROM

THIS PLUG.

ENSUREPROPERGROUND EXISTSBEFOREUSE.

IF LOCAL CODES PERHIT,

AN EXTERNAL GROUND WIRE

(NOT PROVIDED), WHICH HEETS

LOCAL CODES, HAY BE ADDED

BYATTACHING TO THE GREEN

GROUND SCREW ON THE REAR

OF THE DRYER,AND TO A GROUNDED

METAL COLD WATER PIPE OR OTHER

ESTABLISHED GROUND.

Instructions

[-6-]EXHAUST INFORMATION

WARNING -IN CANADAANDINTHE

UNITED STATES,THE REQUIRED EXHAUST DUCT

DIAMETER IS 4 IN (102ram). DO NOT USEDUCT

LONGER THAN SPECIFIED IN THE EXHAUST

LENGTH TABLE.

Usingexhaustlongerthan specifiedlengthwill:

• Increasethedrying timesandthe energycost.

• Reducethe dryer life.

• Accumulatelint, creatinga potential firehazard.

Thecorrect exhaustinstallation isYOURRESPONSIBILITY.

Problemsdueto incorrect installation are not covered by

the warranty.

Removeanddiscordexistingplasticor metalfoil transition

duct and replacewith ULlistedtransition duct.

TheMAXIMUMALLOWABLEduct lengthand numberof

bendsof theexhaustsystemdependsupon thetype ofduct,

numberofturns,thetgpe ofexhausthood(wallcap),and all

conditionsnotedbelow.Themaximumduct lengthfor rigid

metal duct isshownin thetable below.

EXHAUST LENGTH

RECOMHENDEDHAXIHUH LENGTH

Exhaust Hood Tgpes

Recommended Use only for short

run installations

4" DIA.

_l J..... 21/2"

No. of 90 ° Rigid

Elbows Metal

0 60 Feet

1 45 Feet

2 35 Feet

3 25 Feet

4 15 Feet

4" J_

Rigid

Metal

90 Feet

60 Feet

45 Feet

35 Feet

25 Feet

EXHAUST SYSTEM CHECK LIST

HOOD ORWALL CAP

• Terminateina mannerto preventback draftsor entrgof birds

or otherwildlife.

• Terminationshouldpresentminimal resistanceto the exhaust

air flow and shouldrequirelittleor nomaintenanceto prevent

clogging.

•Never installa screenin or overtheexhaustduct.Thiscould

causelint buildup.

• Wallcapsmust beinstalledat least12 in.abovegroundlevel

or any otherobstructionwith the openingpointeddown.

SEPARATIONOFTURNS

Forbest performance,separateallturns bg at least4 ft. of

straightduct, includingdistancebetweenlastturn and exhaust

hood.

TURNSOTHERTHAN90°

• Oneturn of 45°or lessmegbeignored.

• Two450turns shouldbetreated asone 900turn.

• Eachturn over450shouldbetreated asone 900turn.

SEALINGOFJOINTS

• Alljointsshouldbetight to avoidleaks.Themaleendof each

sectionofduct must pointawagfrom the dryer.

• Donotassembletheductwork with fastenersthat extend into

the duct.Theywillserveasa collectionpointfor lint.

• Ductjointscan bemadeair and moisture-tightby wrapping

the overlappedjoints with duct tape.

• Horizontalrunsshouldslopedown toward theoutdoors l_inch

per foot

INSULATION

Ductwork that runsthroughan unheatedareaor isnear air

conditioningshouldbe insulatedto reducecondensationand

lintbuild-up.

Installation instructions

[_ EXHAUST CONNECTION

WARNING - TOREDUCETHE

RISK OF FIRE OR PERSONAL INJURY:

* This clothes drger must be exhausted to the outdoors,

* Use onlg 4" rigid metal ducting for the home exhaust

duct.

* Use onlg 4" rigid metal or UL-listed flexible metal

(semi-rigid or foil-tgpe) duct to connect the drger

to the home exhaust duct. It must be installed

in accordance with the instructions found in

"Connecting The Drger To House Vent" on page 6 of

this manual.

*Do not terminate exhaust in a chimneg, a wall,

a ceiling, gas vent, crawl space, attic, under an

enclosed floor, or in ang other concealed space of

a building. The accumulated lint could create a fire

hazard.

* Never terminate the exhaust into a common duct

with a kitchen exhaust sgstem. A combination of

grease and lint creates a potential fire hazard.

* Do not use duct longer than specified in the exhaust

length table. Longer ducts can accumulate lint,

creating a potential fire hazard.

*Never install a screen in or over the exhaust duct. This

will cause lint to accumulate, creating a potential fire

hazard.

* Do not assemble ductwork with ang fasteners

that extend into the duct. These fasteners can

accumulate lint, creating a potential fire hazard.

* Do not obstruct incoming or exhausted air.

* Provide an access for inspection end cleaning of

the exhaust sgstem, especiallg at turns and joints.

Exhaust sgstem shell be inspected end cleaned at

least once gear.

THIS DRYER COMES READY FOR REAR

EXHAUSTING. IF SPACE IS LIMITED, USE

THE INSTRUCTIONS IN SECTION 9 TO

EXHAUST DIRECTLY FROM THE SIDES OR

BOTTOM OF THE CABINET.

STANDARD REAR EXHAUST

{Vented ot floor level}

FORSTRAIGHTLINEINSTALLATION,CONNECTTHEDRYEREXHAUSTTO

THEEXTERNALEXHAUSTHOODUSINGDUCTTAPEORCLAMR

CSA)AGA)APPROVED

NEWFLEXIBLEGAS

LINECONNECTOR

GAS

EXTERNAL

INLET

DUCT

PIPE

OPENING

DUCTTAPEOR

DUCTCLAMP

4IIMETALDUCT

(CUTTOPROPER

LENGTH) DUCTTAPEOR

DUCTCLAMP

NOTE:WE STRONGLYRECOMMENDSOLIDMETALEXHAUSTDUCTING.

HOWEVER,IFFLEXIBLEDUCTINGISUSEDITMUSTBEUL-LISTEDMETAL

NOTPLASTIC.

ELBOWHIGHLY

RECOMMENDED-

STANDARD REAR EXHAUST

(Vented obove floor level}

ELBOWHIGHLY

"-/'-_/¢RECOMMENDED

RECOMMENDED

CONFIGURATION

TOMINIMIZE

EXHAUST

BLOCKAGE,

NOTE: ELBOWS WILL PREVENT DUCT

KINKING AND COLLAPSING.

[] LEVELING DRYER

LEVEL

FRONT-TO-BACK,

"-.,.

LEVEL

SIDE-TO-SIDE.

4LEVELINGLEGS

STANDTHEDRYERUPRIGHTNEARTHE

FINALLOCATIONANDADJUSTTHE4 LEVELING

LEGSTOMATCHTHEHEIGHTOFYOURWASHER,

ADJUSTTHE2ANTI-TIPLEGSTOCONTACT

THEFLOOR,

2ANTI-TIPLEGS

Installation

CONNECTING THE DRYER

TO HOUSE VENT

RIGIDMETALTRANSITIONDUCT

• Forbestdryingperformance,a rigid metaltransitionduct is

recommended.

• Rigidmetaltransitionsducts reducethe riskof crushingand

kinking.

UL-LISTEDFLEXIBLEMETAL(SEMI-RIGIDTRANSITIONDUCT

• tfrigid metulduct cannot be used,thenUL-listedflexible metul

(semi-rigid)ducting cun beused(KitWX08X10077).

Neverinstullflexible metulduct inwulls,ceilings,floors or

otherenclosedspaces.

Total lengthofflexiblemetal duct shouldnot exceed8 feet

(2.4m).

Formany applications,installingelbowsat boththedryer

undthe wullishighly recommended(seeillustrutionsbelow).

Elbowsullowthe dryerto sit closetothe wallwithout kinking

andor crushingthetransition duct,maximizingdrying

performance.

Avoidrestingtheduct on sharpobjects.UL-LISTEDFLEXIBLE

METAL(FOIL-TYPE}TRANSITIONDUCT

• tnspeciulinstullutions,it muy be necessurgto connectthe

dryerto the housevent usingu flexiblemetul(foiltype)duct.

A UL-listedflexiblemetul (foil-type)ductmuy be usedONLY

in instullutionswhererigid metulor flexiblemetul (semi-rigid)

ductingcunnot be usedANDwhereu4" diumeter cun be

muintuinedthroughout theentirelengthof thetrunsition

duct.

tnConuduundthe UnitedStutes,only theflexible metul(foil-

type) ductsthut comply with the "Outlinefor ClothesDryer

TrunsitionDuctSubject2158A"shullbe used.

Neverinstullflexible metulduct inwulls,ceilings,floors or

otherenclosedspuces.

Totul lengthofflexiblemetul duct shouldnot exceed8 feet

(2.4m).

Avoidrestingtheduct on shurpobjects.

Forbest dryingperformunce:

1.Slideone endof theduct overthe clothesdryer

outlet pipe.

2.Securethe ductwith u clump.

3.With the dryer in itspermunent position,extendthe

duct to itsfull length.Allow2"of duct to overlupthe

exhuustpipe.Cut off und removeexcessduct. Keep

theduct usstruight uspossiblefor muximumuirflow.

4.Securethe ductto theexhuustpipewith the other

clump.

ELBOWHIGHLY

REC0

"_<._ _ ELBOWSHIGHLY

Instructions

DONOTUSE

EXCESSIVE

EXHAUST

LENGTH

F9-1ALCOVE OR CLOSET INSTALLATION

• tfyourdryer isapprovedfor installationinan alcoveor closet,

it will bestatedon a labelon thedryer back.

• Thedryer MUSTbevented tothe outdoors.Seethe EXHAUST

INFORMATIONsection.

• Minimumcleuruncebetweendryercubinet undudjucent

wullsor other surfacesis:

0in.eitherside

3 in.front and rear

Minimumverticalspacefrom floorto overheadcabinets,

ceiling,etc.is52 in.

Closetdoorsmustbe Iouveredor otherwiseventilatedand

mustcontain a minimumof 60sq.in.of openareaequally

distributed,ifthe closetcontainsboth a washeranda dryer,

doorsmustcontain a minimumof 120sq.in,of openarea

equallydistributed.

Theclosetshouldbe ventedtothe outdoorsto preventgas

pocketingincaseof a gasleukin the supplyline.

Nootherfuel-burningapplianceshallbeinstulledinthe some

closetwith thedryer.

I1OIBATHROOM OR BEDROOM INSTALLATION

• Thedryer MUSTbevented tothe outdoors.SeeEXHAUST

INFORMATIONsection6.

• Theinstullationmustconformwith Ioculcodesor,inthe

ubsenceof Ioculcodes,with theNATIONALFUELGASCODE,

ANSIZ223.

[_]MOBILE OR MANUFACTUREDHOME INSTALLATION

• tnstullationmustconformto theMANUFACTUREDHOME

CONSTRUCTION& SAFETYSTANDARD,TITLE24,PART32-80

or,whensuchstundard isnotapplicuble,with AMERICAN

NATIONALSTANDARDFORMOBILEHOME,NO.50lB.

• Thedryer MUSTbevented tothe outdoorswith the

terminution securelyfastenedtothe mobilehomestructure.

(SeeEXHAUSTINFORMATIONsection6.)

• TheventMUSTNOTbe terminutedbeneuthu mobileor

manufactured home.

• Theventduct muteriul MUSTBEMETAL.

• KIT14-D346-33MUSTbe usedto uttuch thedryer securelyto

the structure.

• TheventMUSTNOTbeconnectedto uny otherduct, vent,or

chimney.

• Donot usesheetmetulscrewsor other refusteningdevices

which extendintothe interiorof theexhaustvent.

• Provideun openingwith u freeareuof ut leust25sq.in.or

introductionof outsideuir intothe dryer room.

Installation

[f2]DRYER EXHAUST TO RIGHT, LEFT

OR BOTTOM CABINET

THIS EXHAUST INSTALLATION, BE SURE

TO DISCONNECT THE DRYER FROM ITS

ELECTRICAL SUPPLY. PROTECT YOUR

HANDS AND ARMS FROM SHARP

EDGES WHEN WORKING INSIDE THE

CABINET. BE SURE TO WEAR GLOVES

/ .......

REMOVE

SCREW

ANDSAVE.

REMOVEjO

DESIRED

KNOCKOUT

(ONEONLY).

Detach and remove the bottom, right or left side knockout

us desired. Remove the screw inside the drger exhaust duct

and save. Pull the duct out of the dryer.

Note: Only 4" round rigid metal ducting allowed inside

dryer. FIXINGHOLE

B A

Cut the duct as shown and keep portion A.

TAB LOC/_TION

BENDTAB

UP45o

Through the rear opening, locate the tab in the middle of

the appliance base. Lift the tab to about 45o using a flat

blade screwdriver.

Instructions

ADDING NEW DUCT

FIXING

HOLE

PORTION"A"

LEFTSIDE

EXHAUST

Reconnectthe cut portion (A)of the duct to the blower

housing. Makesurethat the shortened duct isaligned with

the tab inthe base.Usethe screw saved previouslgto secure

the duct in placethrough the tab on the appliance base.

ADDING ELBOW AND DUCT FOR

EXHAUST TO LEFT SIDE OF CABINET

. Preassemble 4" elbow with 4" duct. Wrap duct tope

around joint.

. Insert duct assemblg, elbow first, through the side

opening and connect the elbow to the drger internal

duct.

CAUTION: Be sure not to pull or damage the

electrical wires inside the dryer when inserting the

duct.

DUCT

TAPE

, Applg duct tape as shown on the joint between the

drger internal duct and the elbow.

,TAPE CAUTION:

Internal ductjoints must be

secured with tape, otherwise

they may separate and cause

a safety hazard.

Installation

ADDING ELBOW FOR EXHAUST

THROUGH BOTTOM OF CABINET

, Insert the elbow through the rear opening and connect

itto the drger internal duct.

Applg duct tape on the joint between the drger internal

duct and elbow, us shown on page 7.

Internal duct joints must be secured with tape,

otherwise they may separate and cause a

safety hazard.

ADDING COVER PLATE TO REAR OF

CABINET

PLATE

(KITWE1H858)

Connect standard metal elbows and ducts to complete

the exhaust sgstem. Cover back opening with a plate (Kit

WE11V1454)available from gout local service provider.

Placedrger in final location.

,_WARNING-NEVER LEAVE THE BACK

OPENING WITHOUT THE PLATE.

Instructions

CHANGING DIRECTION OF

DOOR OPENING

REMOVE4

HINGESCREWS.

REMOVE/4HOLEPLUGSAND

PLACETHEIViINTHEHOLES

ONTHEOPPOSITESIDE.

ROTATEDOOR1800

ANDREINSTALL.

Installation

[_] CONNECTING INLET HOSES

(onsome models)

To produce steam, the drger must connect to the cold

water supplg. Sincethe washer must also connect to the

cold water, a "`7"connector is inserted to allow both inlet

hoses to make that connection at the some time.

NOTE:Use the new inlet hoses provided; never

use old hoses.

1.Turn the cold water faucet off. Removethe washer inlet

hose from the washer fill valve connector (cold).

2. Ensurethe rubber fiat washer isin place and screw

the female coupling of the short hose onto the washer fill

valve connector. Tighten bg hand until firmlg seated.

3. Attach the female end of the ",7"connector to the male

coupling of the short hose. Ensurethe rubber fiat washer

is in place. Tighten bg hand until firmlg seated.

4. Insert the filter screen in the coupling of the washer's

inlet hose. If a rubber fiat washer

isalreadg in place remove it before installing

the filter screen. Attach this coupling to one male end of

the "`7"connector. Tighten bg hand until firmlg seated.

5. Ensurethe rubber fiat washer isin place and attach

the drger's long inlet hose to the other male end of the

"`7"connector. Tighten bg hand until firmlg seated.

6. Ensurethe rubber fiat washer isin place and attach

the other end of the drger's long inlet hose to the fill valve

connector at the bottom of the drger back panel. Tighten

bg hand until firmlg seated.

7. Using pliers, tighten all the couplings with

an additional two-thirds turn.

NOTE:Do not overtighten. Damage to the couplings mag

result.

Instructions

[_ CONNECTING INLET HOSES {cont.}

8. Turn the water faucet on.

9. Check for leaks around the '"7" connector,

faucet and hose couplings.

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUSTbe installed within z_2

in. (107 cm) of gour washer's water inlet. The faucets

MUSTbe 3//4 in. (1.9cm) garden hose-tgpe so inlet hoses

can be connected. Water pressure MUSTbe between 10

and 120 pounds per square inch. ,Tourwater department

can advise gou of gour water pressure.

NOTE:A water softener is recommended to reduce

buildup of scale inside the steam generator if the home

water supplg isverg hard.

[_]SERVICING

WARNING- LABEL ALL WIRES

PRIOR TO DISCONNECTION WHEN

SERVICING CONTROLS. WIRING ERRORS

CAN CAUSE IMPROPER AND DANGEROUS

OPERATION AFTER SERVICING/

INSTALLATION.

For replacement parts and other information, refer to

Owner's Manual for servicing phone numbers.

For Questions on Installation, Call: 1-800-626-2000 (US)or

1-800-561-33/4/4(Canada).

Hotpoint HTDX100GM0WW Installation guide

Hotpoint HTDX100GM0WW Installation guide

Hotpoint HTDX100GM0WW Installation guide

Related papers

Other documents