PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Lot #: 355540 08 / 26 / 13
Date Purchased: ____________________
415802
Multi-Purpose Stand
Harbor View Collection
English .................... Page 1-21
Français ...............Pages 22-24
Espanol .............Páginas 25-27
ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
ADULT ASSEMBLY REQUIRED
Page 2 www.sauder.com/services 415802
TABLE OF CONTENTS
Part Identifi cation .......................3
Hardware Identifi cation .............4
Assembly Steps ....................5-21
Français ..............................22-24
Espanol ...............................25-27
Safety .................................28-30
Warranty ...................................31
PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C TOP 1
D BOTTOM 1
D24 RIGHT DRAWER SIDE 1
D25 LEFT DRAWER SIDE 1
D70 DRAWER BACK 1
D719 DRAWER BOTTOM 1
E SHELF 1
F BACK 1
G LONG DIVIDER 1
H SHORT DIVIDER 2
I RIGHT FRONT LEG 1
J LEFT FRONT LEG 1
K BACK LEG 2
L SKIRT 1
M DRAWER FRONT 1
N FRONT TOP MOLDING 1
O RIGHT TOP MOLDING 1
P LEFT TOP MOLDING 1
Q SHELF MOLDING 1
A
B
C
D
E
F
G
H
H
I
J
K
K
L
M
NP
Q
Page 3
www.sauder.com/services415802
O
D719
D24
D25
D70
HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
NAIL - 33
1N
PULL -1
98K
SILVER 5/8" MACHINE SCREW - 2
15S
SILVER 1-1/8" FLAT HEAD SCREW - 6
10S
MOLDING CONNECTOR - 2
19F
HIDDEN CAM - 20
1F
CAM SCREW - 8
8F
CAM DOWEL -12
2F
LONG METAL PIN - 2
3R
GOLD 5/16" FLAT HEAD SCREW - 8
3S
ANGLE BRACKET - 3
5G
BLACK 9/16" LARGE HEAD SCREW - 6
1S
CAM COVER - 14
12P
TACK GLIDE - 4
12E
SLIDE CAM - 2
10A
BLACK 2-1/4" FLAT HEAD SCREW - 6
26S
BLACK 1-9/16" FLAT HEAD SCREW - 4
30S
35GA CABINET RIGHT - 1 35GB CABINET LEFT - 1 35GC DRAWER RIGHT - 1
35GD DRAWER LEFT - 1
Page 4 www.sauder.com/services 415802
Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted fl oor or on the empty carton to avoid scratching your unit or the fl oor.
Push twenty HIDDEN CAMS (1F) into the ENDS (A and B), BOTTOM (D), and SHELF (E). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM, except the long edges of the ENDS (A and B) and SHELF (E).
Page 5
www.sauder.com/services415802
Do not tighten the HIDDEN CAMS in this step.
Arrow
(12 used)
(20 used)
Arrow
1F
1F
2F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
B
E
D
Do not insert CAM
DOWELS into these edges.
Do not insert CAM
DOWELS into this edge.
Turn eight CAM SCREWS (8F) into the LEGS (I and J) and SHELF MOLDING (Q).
2
2
S
t
e
p
Page 6 www.sauder.com/services 415802
8F
QI
J
Fasten the LEGS (I and J) to the ENDS (A and B). Tighten six HIDDEN CAMS.
Fasten the BACK LEGS (K) to the ENDS (A and B). Use six BLACK 2-1/4" FLAT HEAD SCREWS (26S).
NOTE: Be sure the center holes in the LEGS (K) line up before fastening the LEGS to the ENDS (A and B).
3
3
S
t
e
p
Page 7
www.sauder.com/services415802
K
K
I
J
A
B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
BLACK 2 1/4" FLAT HEAD SCREW
(6 used in this step)
26S
These edges
should be even.
These edges
should be even.
Line up the center
holes in the LEGS
before fastening
to the ENDS.
4
4
S
t
e
p
Page 8 www.sauder.com/services 415802
Roller end
Fasten a CABINET RIGHT (35GA) to the RIGHT END (A) and a CABINET LEFT (35GB) to the LEFT END (B). Use four GOLD
5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
GOLD 5/16" FLAT HEAD SCREW
(4 used for the CABINET RIGHT and LEFT)
3S
3
2
1
Roller end
A
B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
I
J
3
2
1
5
5
S
t
e
p
Page 9
www.sauder.com/services415802
Tap two MOLDING CONNECTORS (19F) into the notches in the MOLDINGS (N, O, and P).
Flat end Flat end
Use your hammer to tap the MOLDING CONNECTOR (19F) into the notches in the MOLDINGS.
19F 19F
N
O
P
Fasten the MOLDINGS (N, O, and P) to the TOP (C). Use six SILVER 1-1/8" FLAT HEAD SCREWS (10S).
6
6
S
t
e
p
Page 10 www.sauder.com/services 415802
N
O
P
C
SILVER 1-1/8" FLAT HEAD SCREW
(6 used in this step)
10S
Flat edge
Surface with holes
Fasten the SHELF (E) and BOTTOM (D) to the LEFT END (B). Tighten four HIDDEN CAMS.
7
7
S
t
e
p
Page 11
www.sauder.com/services415802
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Arrow
Maximum
210 degrees
Minimum
190 degrees
B
D
E
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Roller end
Edge with
HIDDEN CAMS
This hole
must be here.
Fasten the RIGHT END (A) to the SHELF (E) and BOTTOM (D). Tighten four HIDDEN CAMS.
8
8
S
t
e
p
Page 12 www.sauder.com/services 415802
Edge with
CAM DOWELS
A
D
E
Maximum
210 degrees
Minimum
190 degrees
Arrow
Surface without
HIDDEN CAMS
I
Fasten the TOP MOLDINGS (O and P) on the TOP (C) to the ENDS (A and B). Tighten four HIDDEN CAMS.
9
9
S
t
e
p
Page 13
www.sauder.com/services415802
Maximum
210 degrees
Minimum
190 degrees
Arrow
Rounded edge
A
B
C
O
P
N
10
10
S
t
e
p
Page 14 www.sauder.com/services 415802
Fasten three ANGLE BRACKETS (5G) to the SKIRT (L). Use three BLACK 9/16" LARGE HEAD SCREWS (1S).
NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the SKIRT.
Fasten the SKIRT (L) to the ENDS (A and B) and BOTTOM (D). Use three BLACK 9/16" LARGE HEAD SCREWS (1S).
BLACK 9/16" LARGE HEAD SCREW
(6 used for the BRACKETS)
1S
A
B
D
L
L
5G
5G
5G
11
11
S
t
e
p
Page 15
www.sauder.com/services415802
Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit.
Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it “square”.
Fasten the BACK (F) to your unit using the NAILS (1N).
NOTE: Be sure to tap NAILS into the holes that line up over the SHELF (E).
Using your hammer, gently tap four TACK GLIDES (12E) into the bottom edge of the LEGS (I, J, and K).
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NAIL
(33 used in this step)
1N
These holes must line up
over the SHELF (E).
Unfi nished
surface
F
K
K
J
I
12E
Carefully stand your unit upright.
Push a CAM COVER (12P) onto each visible HIDDEN CAM.
NOTE: Do not put CAM COVERS on the HIDDEN CAMS on the bottom front edge of the SHELF (E). These HIDDEN CAMS will
be tightened in the next step.
12
12
S
t
e
p
Page 16 www.sauder.com/services 415802
To cover HIDDEN CAMS
(12 used) 12P
E
13
13
S
t
e
p
Page 17
www.sauder.com/services415802
3R
H
Insert two LONG METAL PINS (3R) into the holes in one of the SHORT DIVIDERS (H). Push the LONG DIVIDER (G) and other
SHORT DIVIDER (H) onto the LONG METAL PINS in the SHORT DIVIDER.
Now, insert the DIVIDERS (G and H) into the opening as shown.
Then, fasten the SHELF MOLDING (Q) to the SHELF (E). Tighten two HIDDEN CAMS.
Push two CAM COVERS (12P) onto these HIDDEN CAMS.
H
G
E
QH
H
G
Finished edge
Long fi nished edge
Finished edge
Finished edge
These edges
should be even.
To cover HIDDEN CAMS
(2 used) 12P
14
14
S
t
e
p
Page 18 www.sauder.com/services 415802
Fasten the DRAWER BACK (D70) to the DRAWER SIDES (D24 and D25). Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S).
NOTE: Be sure the DRAWER BOTTOM (D719) inserts into the groove of the DRAWER BACK (D70).
12
3
D719
The tabs should insert freely into the slots.
Gently tilt the DRAWER SIDES side to
side until the tabs slip into the slots.
UNFINISHED
Be sure the DRAWER
BOTTOM inserts
into the DRAWER
FRONT groove.
VIEW THE T-LOCK BOX VIDEO
D70
Insert the DRAWER SIDES (D24 and D25) at an angle into the
slot at each end of the DRAWER FRONT (M).
Slide the DRAWER BOTTOM (D719) into the grooves in the
DRAWER SIDES (D24 and D25) and DRAWER FRONT (M).
D24
D24
D24
D25
D25
D25
Groove
Start each screw a few turns before
completely tightening any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(4 used in this step)
30S
M
M
15
15
S
t
e
p
Page 19
www.sauder.com/services415802
Insert a SLIDE CAM (10A) into the DRAWER SIDES (D24 and D25).
Fasten a DRAWER RIGHT (35GC) to the RIGHT DRAWER SIDE (D24) and a DRAWER LEFT (35GD) to the LEFT DRAWER
SIDE (D25). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE.
Fasten the PULL (98K) to the DRAWER FRONT (M). Use two SILVER 5/8" MACHINE SCREWS (15S).
1
2
3
1
2
3
Roller end
GOLD 5/16” FLAT HEAD SCREW
(4 used in this step)
3S
D24
D25
Roller end Screw head - turn CAM to
line up holes in SLIDES with
holes in DRAWER SIDES.
10A
10A
98K
M
SILVER 5/8" MACHINE SCREW
(2 used for the PULL)
15S
16
16
S
t
e
p
Page 20 www.sauder.com/services 415802
To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit.
Lift the front of the drawer up and slide it into the unit.
40 lbs.
30 lbs.
15 lbs.
50 lbs. total
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Sauder 415802 Mode d'emploi
- español: Sauder 415802 Instrucciones de operación
Related papers
-
Sauder 410412 Operating instructions
-
-
-
-
-
-
-
-
-
