Schneider Electric Resi9 Enclosures Instruction Sheet

Brand: Schneider Electric

Model: Resi9 Enclosures

Type: Instruction Sheet

Note:

b Remove minimum number of knockouts required for the

incoming and outgoing cables to pass through easily.

bIP rating shall be maintained, suitable cable protection shall

be applied with appropriate conduit.

R9HSBpppS, R9HSBpppF Instruction Sheet

1/2

GEX4520501-00

06/2023

R9HSBpppS

Unboxing

R9HSBpppS R9HSBpppF

2Removal of Front Cover

R9HSBpppSR9HSBpppF

R9HSBpppS, R9HSBpppF

Cable Entry Knockouts

PZ2 PH2

R9HSBpppF

R9HSB110F 1 1 1 1 1 1- 4

R9HSB115F 1 1 1 1 1 21 4

R9HSB215F 1 1 2 1 2 21 4

R9HSB315F 1 1 2 1 3 22 4

R9HSB415F 1 1 3 1 4 33 4

R9HSB115S 1 1 1 1 1 21 4

R9HSB215S 1 1 2 1 2 21 4

R9HSB315S 1 1 2 1 3 22 4

R9HSB415S 1 1 3 1 4 33 4

Commercial

Reference

Number

Instruction

Sheet

White

Label Screw (M4)U-Link

Earth Wire

Comb Busbar

Pin Type

Earth

Conductor

Tag

Pole Filler

GEX6328302

Surface Mount Flush Mount

Resi9 Enclosures

PLEASE NOTE

b This equipment must be installed and maintained by a qualified electrician in

accordance with the appropriate statutory regulations and codes of practice.

All applicable local, regional and national regulations must be complied with

during the installation, use, maintenance and replacement of this device.

This product should not be installed if, when unpacking it, you observe that

it is damaged.

Schneider Electric cannot be held responsible in the event of noncompliance

with the instructions in this document and in the documents to which it refers.

The service instruction must be observed throughout the life time of this

product.

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

Turn off all power supplying this product before working on it.

Use a voltage tester with a suitable rated voltage in order to check that all

active conductors aren’t energized.

Carefully inspect the work area to check that no tools or objects could have

been left inside the equipment.

Failure to follow these instructions will result in death or serious injury.

DANGER

LIGHT 2

LIGHT 3

LIGHT 4

LIGHT 5

SUB BOARD

WORK SHOP

SUB BOARD

HEATER

NIGHT STORE

HEATER

FRIDGE

NIGHT STORE

HEATER

LIGHT 1

2/2

GEX4520501-00

Mounting of Enclosures

5Finishing Installation

5.1 Assembly of Front Cover

5.2 Labelling and Assembly of Pole Filler

R9APF15

4DIN Mounting of Devices

70 mm

Wall

Note: Reverse the enclosure based

on cable entry (top or bottom).

R9HSBpppS, R9HSBpppF

Schneider Electric Industries SAS

35, rue Joseph Monier

CS 30323

F - 92506 Rueil Malmaison Cedex

www.se.com

AA AB

KITCHEN KITCHEN HOT WATER

SYSTEM

HOT WATER

SYSTEM LOUNGE

Instal led By

PHONE No

Instal led By

PHONE No

AIN EARTH LOCATION

RESIDUAL CURRENT DEVI CE RESIDUAL CURRENT DEVI CE MAIN ISOLATING SWITCH ALARM

AIN SWITCH ALARM

RESIDUAL CURRENT DEVI CE RESIDUAL CURRENT DEVI CE RESIDUAL CURRENT DEVI CE

RESIDUAL CURRENT DEVI CE RESIDUAL CURRENT DEVI CE MAIN SWITCH

AIN SWITCHRESIDUAL CURRENT DEVI CE

MAIN ISOLATING SWITCH MAIN ISOLATING SWITCH

AIR COND. 1 AIR COND. 2 AIR COND. 3 AIR COND. 4

POWER 6 POWER 7 POWER 8 POWER 9 POWER 10 DISH WASHER

POWER 1 POWER 2 POWER 3 POWER 4 POWER 5 GARAGE

DISH WASHER WALL OVEN WALL OVEN WALL OVEN

PUMP

LIGHT 1 LIGHT 2 LIGHT 3 LI GHT 4 LIGHT 5 SUB BOARD

NIGHT STORE

HEATER

DRIVE WAY

LIGHT

WORK SHOP

POWER 11 POWER 12 POWER 13 POWER 14 POWER 15 LAUNDRY LAUNDRY

NDER FLOOR

HEAT

NDER FLOOR

HEAT

OVER VOLTAG

ARRESTER

VER VOLTAGE

ARRESTER SPA SPA POOL

SUB BOARD HEATER HEATER

LIGHT 6 LIGHT 7 LIGHT 8 LI GHT 9 LIGHT 10 FRIDGE

BED 1 BED 2 BED 3 MEN PEN

POOL HOT WATER OFF PEAK SWITCH

RANGE RANGE RANGE HOB SAUNA SMOKE

DETECTOR

SMOKE

DETECTOR HOT WATER OFF PEAK SWITCH

FRIDGE

IGHT STORE

HEATER

OVER VOLTAG

ARRESTER

Surge Protection

Fire Protection

Cable Protection

People Protection

Isolator Switch

0.8 N.m

Screw M4 x4

NOTICE

EQUIPMENT DAMAGE

Do not open the enclosure door beyond the stopper.

Failure to follow this instruction will result in the

equipment damage.

Note: Refer the instruction sheet of devices for more information.

Note: Mark the points corresponding to the

box keyholes and drill holes accordingly.

Surface Mount:

R9HSBpppS

Flush Mount:

Note:

Fix the box in the wall cavity with the outer edges projecting out the

wall's surface (marking provided).

Option of metal back plate available - Refer catalog for more details.

R9HSBpppF

Screw M5 x4

180°

0.8 N.m

C (mm) D (mm)

R9HSB115F 335 223

335 357

R9HSB215F

E (mm)

R9HSB315F

R9HSB415F

335

631

765

R9HSB110F 246 223 70

A (mm) B (mm)

260 115

338 309

338 559

338 693

R9HSB115S

R9HSB215S

R9HSB315S

R9HSB415S

Schneider Electric Resi9 Enclosures Instruction Sheet

Schneider Electric Resi9 Enclosures Instruction Sheet

Schneider Electric Resi9 Enclosures Instruction Sheet

Related papers

Other documents