Renkforce GT-730FL-S Owner's manual

Brand: Renkforce

Model: GT-730FL-S

Category: Coffee making accessories

Type: Owner's manual

Page is loading ...

• If you have questions which remain unanswered by these operating instructions,

contact our technical support service or other technical personnel.

b) Rechargeable batteries

• The rechargeable battery is built into the product and cannot be replaced.

• Never attempt to damage the rechargeable battery. Damaging the casing of the

rechargeable battery may cause it to explode or catch re! Unlike conventional

batteries (e.g. AA or AAA batteries), the casing of the LiPo rechargeable battery is

made of a sensitive plastic lm.

• Never short-circuit the contacts of the rechargeable battery. Do not throw the

battery or the product into open ames. This may cause a re or explosion!

• Charge the rechargeable battery regularly, even when you are not using the

product. You do not need to discharge the rechargeable battery before recharging

it.

• Never charge the battery when the product is unattended.

Product overview

1 ON/OFF switch

2 Data tag key for position marking

3 Status indicator and loading status

4 GPS status indicator / memory status

Operation

a) Charging the rechargeable battery

• The battery needs to be charged for approximately 4 hours before rst use. Subsequent

charges usually take about 2 hours.

• Connect the device to a USB port with an output current of least 500 mA. This can be either

a USB power adapter or a USB port on your computer.

• The status indicator (3) will turn green when the battery is charging. It will turn off again when

the battery is fully charged. The status indicator (3) will turn red when the battery is empty.

b) Turning on and off

• To turn the device on and off, move the on/off switch to the corresponding position.

• We recommend that you place the GPS logger outside for approximately 15–20 minutes

before rst use to ensure that it detects all GPS satellites. This is indicated by the status

indicator (4).

Status indicator (4):

- Constant blue = Position not detected

- Flashing blue (slow) = Position detected

- Flashing blue (fast) = Location information is being recorded

c) Installing the software / USB driver

• Insert the software CD into the CD drive.

• Run the software installer and follow the onscreen instructions.

• Once you have installed the software, insert the device into a USB port and turn it on using

the on/off switch (1). The GPS data logger will be recognised by the operating system.

• Launch the software.

• Refer to the manual on the CD for detailed instructions on how to install and use the software.

d) Recording data / data tag

• Switch on the device using the on/off switch (1).

• We recommend that you place the GPS logger outside for approximately 15–20 minutes

before rst use to ensure that it detects all GPS satellites. This is indicated by the GPS status

indicator (4) (see "b) Turning on and off").

• Press and hold the data tag button (2) for a few seconds to locate your position. The blue

status LED (4) will start to ash quickly.

Signal reception may be impaired by obstacles such as buildings, tunnels and

trees. Other sources of interference can also affect performance (e.g. if the device

is connected to a computer when it is attempting to locate your position for the rst

time). For best results, allow the device to obtain your position before connecting it

to a computer.

Care and cleaning

• Always disconnect the product from the power supply before cleaning it.

• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may

damage the casing or cause the product to malfunction.

• Use a dry, lint-free cloth to clean the product.

Operating instructions

GPS-data logger GT-730

Item no. 373686

Intended use

This USB GPS data logger features a GPS receiver with an SIRF-4 chipset. It is designed

to track your location and can record up to 256,000 values. The GPS receiver is tted with a

built-in (non-removable) lithium polymer battery. This allows you to use the device without an

external power supply. The GPS receiver can be connected to a computer via a USB port to

read data and charge the battery. It also comes with a software CD that enables you to display

information graphically and analyse positioning data.

For safety and approval purposes, you must not rebuild and/or modify this product. Using the

product for purposes other than those described above may damage the product. In addition,

improper use can cause hazards such as a short circuit, re or electric shock. Read the

instructions carefully and store them in a safe place. Make this product available to third parties

only together with its operating instructions.

This product complies with statutory national and European regulations. All company and

Delivery contents

• GPS dongle

• Protective cap

• CD with driver/software/digital user manual

• Operating instructions

Up-to-date operating instructions

Download the latest operating instructions at www.conrad.com/downloads or scan the QR code

on this page. Follow the instructions on the website.

System requirements

• Laptop or desktop PC with a free USB port

• CD-ROM drive

• Approx. 55 MB free hard disk space

• Operating system: Windows

98SE or later (up to Windows

Explanation of symbols

The symbol with the lightning in the triangle indicates that there is a risk to your

health, e.g. due to an electric shock.

This symbol is used to highlight important information in these operating instructions.

Always read this information carefully.

This symbol indicates special information and advice on how to use the product.

Safety information

Read the operating instructions and safety information carefully. If you do

not follow the safety instructions and information on proper handling in this

manual, we will assume no liability for any resulting personal injury or damage

to property. Such cases will invalidate the warranty/guarantee.

a) General information

• This product is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly, as it may become

dangerous playing material for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, stop using it and prevent

unauthorized use. Safe operation can no longer be guaranteed if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stress.

• Always handle the product carefully. Jolts, impacts or a fall even from a low height

may damage the product.

• Always observe the safety and operating instructions of any other devices which

are connected to the product.

• Consult a technician if you are not sure how to use or connect the product.

• Maintenance, modications and repairs must be done by a technician or an

authorized repair centre.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method (e.g. photocopying, microlming, or the capture in

electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.

This publication represents the technical status at the time of printing.

Declaration of Conformity (DOC)

Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declares that this

product conforms to the 2014/53/EU directive.

Click on the following link to read the full text of the EU declaration of conformity:

www.conrad.com/downloads

Select a language by clicking on a ag symbol, and then enter the product order

number in the search box. The EU Declaration of Conformity is available for

download in PDF format.

Disposal

Electronic devices are recyclable waste and must not be placed in household waste.

Always dispose of the product according to the relevant statutory regulations.

You thus fulll your statutory obligations and contribute to the protection of the environment.

Technical data

Charging voltage/current ....................5 V/DC, 500 mA

USB version ........................................1.1/2.0

Operating voltage ...............................3.7 V/DC

Battery type ........................................Lithium polymer

Supported operating systems ............. Windows

98SE, ME, 2000 SP 4 ,

XP (32/64-bit with SP2, SP3) (32-bit only),

Server 2003 (32/64-bit), Vista (32/64-bit), 7 (32/64-bit)

Device driver .......................................STMicroelectronic v1.3.10 (04/25, 2010)

Cold start ............................................< 30 seconds (at –147 dBm)

Warm start ..........................................< 1 second (under a clear sky)

GPS accuracy .....................................5 m (circular radius)

Dimensions (W x H x D) .....................29 x 76 x 18 mm

Weight ................................................34 g

Page is loading ...

Renkforce GT-730FL-S Owner's manual

Brand: Renkforce

Model: GT-730FL-S

Category: Coffee making accessories

Type: Owner's manual

Download PDF

report

in other languages

français: Renkforce GT-730FL-S Le manuel du propriétaire
Deutsch: Renkforce GT-730FL-S Bedienungsanleitung
Nederlands: Renkforce GT-730FL-S de handleiding

Renkforce GT-730FL-S Owner's manual

Renkforce GT-730FL-S Owner's manual

in other languages

Related papers

Other documents