Builders Choice HDMWD1128X Installation guide

Brand
Builders Choice
Model
HDMWD1128X
Type
Installation guide
RediShelf
Premium quality
melamine shelving,
furniture and
closet organizers.
•Thermallyfused
melamineprovides
durablesurface,
resistanttochips,
scratchesandstains
•Compatiblewith
mostshelf
mountinghardware
EASY TO ASSEMBLE
InstallationandCleaning
• To ensure clean cutting, use a fine-tooth carbide
tip blade. If using a circular saw, cut the exposed
side of the board face down; if using a handsaw,
cut the exposed side of the board face up. Put
masking tape on the cutline to reduce chip out
when cutting.
• We recommend drilling a pilot hole using a
3
∕32”
bit if you use no. 8 x 1-5/8” countersunk screws.
• Using plastic end caps to cover screws will
improve the appearance of your project.
• Use shelf pins in pre-drilled holes for the
shelves.
• Corner brackets are recommended instead of
screws for top shelves.
• Tall units must be secured to the wall by being
screwed into studs.
• Clean with warm water or a mild detergent. Do
not use abrasive cleaners or scouring powders.
Premium quality melamine shelving,
furniture and closet organizers.
MADE IN THE USA
37½”Wide
Bookcase
Home Depot Material List 37½” Bookcase
QTY ITEM INSTRUCTIONS
2
¾” x 11¾” x 97” drilled 1 side
white melamine
Cut both pieces to 78” each to make two side panels
1
¾” x 24” x 48” 1 edge band
white melamine
Cut two 4” x 36” strips for wall mount supports.
2
¾” x 11¾” x 97” 1 edge band
white melamine
Cut six 36” shelves from three 97” shelves. Attach
top and bottom shelves with screws to 78” uprights
2
³/
16
” brass shelf pins
(12 per pack)
Zinc, plastic, and other styles and colors are available. Visit
your local Home Depot hardware aisle
for local options.
1
box
1
5
∕8” coarse thread all-purpose
or drywall screws
1 Phillips screw cover white
2
Phillips head screw cover white
(25 per pack)
Cover the screw heads and improve the appearance
of your project.
www.roseburg.com or (800) 245-1115
RediShelf
Premium quality
melamine shelving,
furniture and
closet organizers.
•Thermallyfused
melamineprovides
durablesurface,
resistanttochips,
scratchesandstains
•Compatiblewith
mostshelf
mountinghardware
EASY TO ASSEMBLE
InstallationandCleaning
• To ensure clean cutting, use a fine-tooth carbide
tip blade. If using a circular saw, cut the exposed
side of the board face down; if using a handsaw,
cut the exposed side of the board face up. Put
masking tape on the cutline to reduce chip out
when cutting.
• We recommend drilling a pilot hole using a
3
∕32”
bit if you use no. 8 x 1-5/8” countersunk screws.
• Using plastic end caps to cover screws will
improve the appearance of your project.
• Use shelf pins in pre-drilled holes for the
shelves.
• Corner brackets are recommended instead of
screws for top shelves.
• Tall units must be secured to the wall by being
screwed into studs.
• Clean with warm water or a mild detergent. Do
not use abrasive cleaners or scouring powders.
Premium quality melamine shelving,
furniture and closet organizers.
MADE IN THE USA
96”Wide
Closet
Organizer
Home Depot Material List 96” Closet Organizer
QTY ITEM INSTRUCTIONS
2
¾” x 15¾” x 97”
drilled 1-side white melamine
with 1-side edge band
Cut each panel to 80” for two inside upright panels.
5
¾” x 15¾” x 97”
1 edge band white melamine
Cut two shelves to 80” for outside uprights. Cut six
32” shelves from two 97” shelves. Leave one shelf
at 97” for top.
1
¾” x 24” x 48” 1 edge band
white melamine
Cut four 4” x 31” strips for wall mount supports.
2
³/
16
” brass shelf pins
(12 per pack)
Zinc, plastic, and other styles and colors are available. Visit
your local Home Depot hardware aisle
for local options.
1
box
1
5
∕8” coarse thread all-purpose
or drywall screws
1
Phillips head screw cover white
(25 per pack)
Cover the screw heads and improve the appearance
of your project.
2
1” corner brace with screws
(4 per pack)
3
1¼” moulding round R/L
(fir or pine as available)
Cut round to 3’ length,
trim to 32” length for use as closet rod.
3 White closet pole socket Used to support closet rod.
www.roseburg.com or (800) 245-1115
RediShelf
Premium quality
melamine shelving,
furniture and
closet organizers.
•Thermallyfused
melamineprovides
durablesurface,
resistanttochips,
scratchesandstains
•Compatiblewith
mostshelf
mountinghardware
EASY TO ASSEMBLE
InstallationandCleaning
• To ensure clean cutting, use a fine-tooth carbide
tip blade. If using a circular saw, cut the exposed
side of the board face down; if using a handsaw,
cut the exposed side of the board face up. Put
masking tape on the cutline to reduce chip out
when cutting.
• We recommend drilling a pilot hole using a
3
∕32”
bit if you use no. 8 x 1-5/8” countersunk screws.
• Using plastic end caps to cover screws will
improve the appearance of your project.
• Use shelf pins in pre-drilled holes for the
shelves.
• Corner brackets are recommended instead of
screws for top shelves.
• Tall units must be secured to the wall by being
screwed into studs.
• Clean with warm water or a mild detergent. Do
not use abrasive cleaners or scouring powders.
Premium quality melamine shelving,
furniture and closet organizers.
MADE IN THE USA
48”Wide
CoffeeTable
Home Depot Material List 48” Coffee Table
QTY ITEM INSTRUCTIONS
2
¾” x 24” x 48” 1 edge band
white melamine
Use one full size panel for top. Cut other to
two 17¼” x 24” pieces for side panels.
1
¾” x 24” x 48” 1 edge band
white melamine
Cut to 11¾” x 36” for the table center support.
1
box
1
5
∕8” coarse thread all-purpose
or drywall screws
3
1” corner brace with screws
(4 per pack)
Fasten the side panels to the center support using
corner braces. Fasten the table top to the center
support using corner braces.
1
¾” x 25’ white melamine
iron-on edge banding
Follow manufacturer instructions to apply iron-on
melamine edge banding to any exposed panel
edges.
1
Nail-on Plastic Cushion Glide
(4 per pack)
Fasten two plastic furniture cushion glides to the
bottom of each side panel.
www.roseburg.com or (800) 245-1115
RediShelf
Premium quality
melamine shelving,
furniture and
closet organizers.
•Thermallyfused
melamineprovides
durablesurface,
resistanttochips,
scratchesandstains
•Compatiblewith
mostshelf
mountinghardware
EASY TO ASSEMBLE
InstallationandCleaning
• To ensure clean cutting, use a fine-tooth carbide
tip blade. If using a circular saw, cut the exposed
side of the board face down; if using a handsaw,
cut the exposed side of the board face up. Put
masking tape on the cutline to reduce chip out
when cutting.
• We recommend drilling a pilot hole using a
3
∕32”
bit if you use no. 8 x 1-5/8” countersunk screws.
• Using plastic end caps to cover screws will
improve the appearance of your project.
• Use shelf pins in pre-drilled holes for the
shelves.
• Corner brackets are recommended instead of
screws for top shelves.
• Tall units must be secured to the wall by being
screwed into studs.
• Clean with warm water or a mild detergent. Do
not use abrasive cleaners or scouring powders.
Premium quality melamine shelving,
furniture and closet organizers.
MADE IN THE USA
25½”Wide
EndTable
Home Depot Material List 25½” Wide End Table
QTY ITEM INSTRUCTIONS
1
¾” x 15¾” x 97” 1 edge band
white melamine
Out of one 15¾” x 97” shelf, cut one piece to 15¾”
x251∕2”fortop,twoto15¾”x231∕4”forsides,
andoneto15¾”x24”forshelf.
1
¾”x24”x48”1edgeband
white melamine
Cut to 11¾” x 27¾” for the table center brace.
1
box
1
5
∕8” coarse thread all-purpose
or drywall screws
3
1” corner brace with screws
(4perpack)
Fasten the table top to the center support using
corner braces. Fasten the side panels to the center
support using corner braces.
1
¾” x 25” white melamine iron-
on edge-banding
Follow manufacturer instructions to apply iron-on
melamine edge banding to any exposed panel
edges.
1
Phillips head screw cover white
(25perpack)
Cover the screw heads and improve the appearance
of your project.
1
Nail-on Plastic Cushion Glide
(4perpack)
Fasten two plastic furniture cushion glides to the
bottom of each side panel.
www.roseburg.comor(800)245-1115
RediShelf
Premium quality
melamine shelving,
furniture and
closet organizers.
•Thermallyfused
melamineprovides
durablesurface,
resistanttochips,
scratchesandstains
•Compatiblewith
mostshelf
mountinghardware
EASY TO ASSEMBLE
InstallationandCleaning
• To ensure clean cutting, use a fine-tooth carbide
tip blade. If using a circular saw, cut the exposed
side of the board face down; if using a handsaw,
cut the exposed side of the board face up. Put
masking tape on the cutline to reduce chip out
when cutting.
• We recommend drilling a pilot hole using a
3
∕32”
bit if you use no. 8 x 1-5/8” countersunk screws.
• Using plastic end caps to cover screws will
improve the appearance of your project.
• Use shelf pins in pre-drilled holes for the
shelves.
• Corner brackets are recommended instead of
screws for top shelves.
• Tall units must be secured to the wall by being
screwed into studs.
• Clean with warm water or a mild detergent. Do
not use abrasive cleaners or scouring powders.
Premium quality melamine shelving,
furniture and closet organizers.
MADE IN THE USA
82”Wide
Laundry
Organizer
Home Depot Material List 82” Laundry Organizer
QTY ITEM INSTRUCTIONS
4
¾” x 15¾” x 97”
drilled 1-side white melamine
with 1-side edge band
Cut each panel to 84” for side and middle
upright panels.
5
¾” x 15¾” x 97”
1 edge band white melamine
Cuttwoshelvesto611∕2”fortopandbottom
middle sections. Cut three 97” shelves into sixteen
15¾” shelves - twelve for the upright sections
(7 on the left sides, 5 on the right side),
and four for the middle section.
1
¾” x 24” x48”
1 edge band white melamine
Cut two 4” x 15¾” strips for wall mount supports.
2
³/
16
” brass shelf pins
(12 per pack)
Zinc, plastic, and other styles and colors are available. Visit your
local Home Depot hardware aisle
for local options.
1
box
1
5
∕8” coarse thread all-purpose
or drywall screws
2
Phillips head screw cover white
(25 per pack)
Cover the screw heads and improve the appearance
of your project.
2
1” corner brace with screws
(4 per pack)
1
1¼” moulding round R/L
(fir or pine as available)
Cut round to 3’ length,
trim to 32” length for use as closet rod.
1 White closet pole socket Used to support closet rod.
www.roseburg.com or (800) 245-1115
RediShelf
Premium quality
melamine shelving,
furniture and
closet organizers.
•Thermallyfused
melamineprovides
durablesurface,
resistanttochips,
scratchesandstains
•Compatiblewith
mostshelf
mountinghardware
EASY TO ASSEMBLE
InstallationandCleaning
• To ensure clean cutting, use a fine-tooth carbide
tip blade. If using a circular saw, cut the exposed
side of the board face down; if using a handsaw,
cut the exposed side of the board face up. Put
masking tape on the cutline to reduce chip out
when cutting.
• We recommend drilling a pilot hole using a
3
∕32”
bit if you use no. 8 x 1-5/8” countersunk screws.
• Using plastic end caps to cover screws will
improve the appearance of your project.
• Use shelf pins in pre-drilled holes for the
shelves.
• Corner brackets are recommended instead of
screws for top shelves.
• Tall units must be secured to the wall by being
screwed into studs.
• Clean with warm water or a mild detergent. Do
not use abrasive cleaners or scouring powders.
Premium quality melamine shelving,
furniture and closet organizers.
MADE IN THE USA
48”Wide
Desk
Home Depot Material List 48” Wide Desk
QTY ITEM INSTRUCTIONS
4
¾” x 24” x 48” 1 edge band
white melamine
Use one full size panel for top. Out of one 24”
x 48” panel, cut one piece to 24” x 29¼” for an
upright panel, and the remainder to 18” for a
shelf. Repeat this step two more times for the two
remaining 24” x 48” panels so that you end up
with three upright panels and three shelves.
1
¾” x 24” x 48” 1 edge band
white melamine
Cut to 11¾” x 27¾” for the desktop brace.
1
box
1
5
∕8” coarse thread all-purpose
or drywall screws
2
1” corner brace with screws
(4 per pack)
Fasten the desktop to the upright panels using
corner braces.
1
¾” x 25’ white melamine iron-
on edge-banding
Follow manufacturer instructions to apply iron-on
melamine edge banding to any exposed panel
edges.
1
Phillips head screw cover white
(25 per pack)
Cover the screw heads and improve the appearance
of your project.
www.roseburg.com or (800) 245-1115
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Builders Choice HDMWD1128X Installation guide

Brand
Builders Choice
Model
HDMWD1128X
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents