2. Builder's Choice
  3. HDMM11608X

Builder's Choice HDMM11608X Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Builder's Choice HDMM11608X Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
RediShelf
Premium quality
melamine shelving,
furniture and
closet organizers.
•Thermallyfused
melamineprovides
durablesurface,
resistanttochips,
scratchesandstains
•Compatiblewith
mostshelf
mountinghardware
EASY TO ASSEMBLE
InstallationandCleaning
• To ensure clean cutting, use a fine-tooth carbide
tip blade. If using a circular saw, cut the exposed
side of the board face down; if using a handsaw,
cut the exposed side of the board face up. Put
masking tape on the cutline to reduce chip out
when cutting.
• We recommend drilling a pilot hole using a
3
∕32”
bit if you use no. 8 x 1-5/8” countersunk screws.
• Using plastic end caps to cover screws will
improve the appearance of your project.
• Use shelf pins in pre-drilled holes for the
shelves.
• Corner brackets are recommended instead of
screws for top shelves.
• Tall units must be secured to the wall by being
screwed into studs.
• Clean with warm water or a mild detergent. Do
not use abrasive cleaners or scouring powders.
Premium quality melamine shelving,
furniture and closet organizers.
MADE IN THE USA
37½”Wide
Bookcase
Home Depot Material List 37½” Bookcase
QTY ITEM INSTRUCTIONS
2
¾” x 11¾” x 97” drilled 1 side
white melamine
Cut both pieces to 78” each to make two side panels
1
¾” x 24” x 48” 1 edge band
white melamine
Cut two 4” x 36” strips for wall mount supports.
2
¾” x 11¾” x 97” 1 edge band
white melamine
Cut six 36” shelves from three 97” shelves. Attach
top and bottom shelves with screws to 78” uprights
2
³/
16
” brass shelf pins
(12 per pack)
Zinc, plastic, and other styles and colors are available. Visit
your local Home Depot hardware aisle
for local options.
1
box
1
5
∕8” coarse thread all-purpose
or drywall screws
1 Phillips screw cover white
2
Phillips head screw cover white
(25 per pack)
Cover the screw heads and improve the appearance
of your project.
www.roseburg.com or (800) 245-1115
RediShelf
Premium quality
melamine shelving,
furniture and
closet organizers.
•Thermallyfused
melamineprovides
durablesurface,
resistanttochips,
scratchesandstains
•Compatiblewith
mostshelf
mountinghardware
EASY TO ASSEMBLE
InstallationandCleaning
• To ensure clean cutting, use a fine-tooth carbide
tip blade. If using a circular saw, cut the exposed
side of the board face down; if using a handsaw,
cut the exposed side of the board face up. Put
masking tape on the cutline to reduce chip out
when cutting.
• We recommend drilling a pilot hole using a
3
∕32”
bit if you use no. 8 x 1-5/8” countersunk screws.
• Using plastic end caps to cover screws will
improve the appearance of your project.
• Use shelf pins in pre-drilled holes for the
shelves.
• Corner brackets are recommended instead of
screws for top shelves.
• Tall units must be secured to the wall by being
screwed into studs.
• Clean with warm water or a mild detergent. Do
not use abrasive cleaners or scouring powders.
Premium quality melamine shelving,
furniture and closet organizers.
MADE IN THE USA
96”Wide
Closet
Organizer
Home Depot Material List 96” Closet Organizer
QTY ITEM INSTRUCTIONS
2
¾” x 15¾” x 97”
drilled 1-side white melamine
with 1-side edge band
Cut each panel to 80” for two inside upright panels.
5
¾” x 15¾” x 97”
1 edge band white melamine
Cut two shelves to 80” for outside uprights. Cut six
32” shelves from two 97” shelves. Leave one shelf
at 97” for top.
1
¾” x 24” x 48” 1 edge band
white melamine
Cut four 4” x 31” strips for wall mount supports.
2
³/
16
” brass shelf pins
(12 per pack)
Zinc, plastic, and other styles and colors are available. Visit
your local Home Depot hardware aisle
for local options.
1
box
1
5
∕8” coarse thread all-purpose
or drywall screws
1
Phillips head screw cover white
(25 per pack)
Cover the screw heads and improve the appearance
of your project.
2
1” corner brace with screws
(4 per pack)
3
1¼” moulding round R/L
(fir or pine as available)
Cut round to 3’ length,
trim to 32” length for use as closet rod.
3 White closet pole socket Used to support closet rod.
www.roseburg.com or (800) 245-1115
RediShelf
Premium quality
melamine shelving,
furniture and
closet organizers.
•Thermallyfused
melamineprovides
durablesurface,
resistanttochips,
scratchesandstains
•Compatiblewith
mostshelf
mountinghardware
EASY TO ASSEMBLE
InstallationandCleaning
• To ensure clean cutting, use a fine-tooth carbide
tip blade. If using a circular saw, cut the exposed
side of the board face down; if using a handsaw,
cut the exposed side of the board face up. Put
masking tape on the cutline to reduce chip out
when cutting.
• We recommend drilling a pilot hole using a
3
∕32”
bit if you use no. 8 x 1-5/8” countersunk screws.
• Using plastic end caps to cover screws will
improve the appearance of your project.
• Use shelf pins in pre-drilled holes for the
shelves.
• Corner brackets are recommended instead of
screws for top shelves.
• Tall units must be secured to the wall by being
screwed into studs.
• Clean with warm water or a mild detergent. Do
not use abrasive cleaners or scouring powders.
Premium quality melamine shelving,
furniture and closet organizers.
MADE IN THE USA
48”Wide
CoffeeTable
Home Depot Material List 48” Coffee Table
QTY ITEM INSTRUCTIONS
2
¾” x 24” x 48” 1 edge band
white melamine
Use one full size panel for top. Cut other to
two 17¼” x 24” pieces for side panels.
1
¾” x 24” x 48” 1 edge band
white melamine
Cut to 11¾” x 36” for the table center support.
1
box
1
5
∕8” coarse thread all-purpose
or drywall screws
3
1” corner brace with screws
(4 per pack)
Fasten the side panels to the center support using
corner braces. Fasten the table top to the center
support using corner braces.
1
¾” x 25’ white melamine
iron-on edge banding
Follow manufacturer instructions to apply iron-on
melamine edge banding to any exposed panel
edges.
1
Nail-on Plastic Cushion Glide
(4 per pack)
Fasten two plastic furniture cushion glides to the
bottom of each side panel.
www.roseburg.com or (800) 245-1115
RediShelf
Premium quality
melamine shelving,
furniture and
closet organizers.
•Thermallyfused
melamineprovides
durablesurface,
resistanttochips,
scratchesandstains
•Compatiblewith
mostshelf
mountinghardware
EASY TO ASSEMBLE
InstallationandCleaning
• To ensure clean cutting, use a fine-tooth carbide
tip blade. If using a circular saw, cut the exposed
side of the board face down; if using a handsaw,
cut the exposed side of the board face up. Put
masking tape on the cutline to reduce chip out
when cutting.
• We recommend drilling a pilot hole using a
3
∕32”
bit if you use no. 8 x 1-5/8” countersunk screws.
• Using plastic end caps to cover screws will
improve the appearance of your project.
• Use shelf pins in pre-drilled holes for the
shelves.
• Corner brackets are recommended instead of
screws for top shelves.
• Tall units must be secured to the wall by being
screwed into studs.
• Clean with warm water or a mild detergent. Do
not use abrasive cleaners or scouring powders.
Premium quality melamine shelving,
furniture and closet organizers.
MADE IN THE USA
25½”Wide
EndTable
Home Depot Material List 25½” Wide End Table
QTY ITEM INSTRUCTIONS
1
¾” x 15¾” x 97” 1 edge band
white melamine
Out of one 15¾” x 97” shelf, cut one piece to 15¾”
x251∕2”fortop,twoto15¾”x231∕4”forsides,
andoneto15¾”x24”forshelf.
1
¾”x24”x48”1edgeband
white melamine
Cut to 11¾” x 27¾” for the table center brace.
1
box
1
5
∕8” coarse thread all-purpose
or drywall screws
3
1” corner brace with screws
(4perpack)
Fasten the table top to the center support using
corner braces. Fasten the side panels to the center
support using corner braces.
1
¾” x 25” white melamine iron-
on edge-banding
Follow manufacturer instructions to apply iron-on
melamine edge banding to any exposed panel
edges.
1
Phillips head screw cover white
(25perpack)
Cover the screw heads and improve the appearance
of your project.
1
Nail-on Plastic Cushion Glide
(4perpack)
Fasten two plastic furniture cushion glides to the
bottom of each side panel.
www.roseburg.comor(800)245-1115
RediShelf
Premium quality
melamine shelving,
furniture and
closet organizers.
•Thermallyfused
melamineprovides
durablesurface,
resistanttochips,
scratchesandstains
•Compatiblewith
mostshelf
mountinghardware
EASY TO ASSEMBLE
InstallationandCleaning
• To ensure clean cutting, use a fine-tooth carbide
tip blade. If using a circular saw, cut the exposed
side of the board face down; if using a handsaw,
cut the exposed side of the board face up. Put
masking tape on the cutline to reduce chip out
when cutting.
• We recommend drilling a pilot hole using a
3
∕32”
bit if you use no. 8 x 1-5/8” countersunk screws.
• Using plastic end caps to cover screws will
improve the appearance of your project.
• Use shelf pins in pre-drilled holes for the
shelves.
• Corner brackets are recommended instead of
screws for top shelves.
• Tall units must be secured to the wall by being
screwed into studs.
• Clean with warm water or a mild detergent. Do
not use abrasive cleaners or scouring powders.
Premium quality melamine shelving,
furniture and closet organizers.
MADE IN THE USA
82”Wide
Laundry
Organizer
Home Depot Material List 82” Laundry Organizer
QTY ITEM INSTRUCTIONS
4
¾” x 15¾” x 97”
drilled 1-side white melamine
with 1-side edge band
Cut each panel to 84” for side and middle
upright panels.
5
¾” x 15¾” x 97”
1 edge band white melamine
Cuttwoshelvesto611∕2”fortopandbottom
middle sections. Cut three 97” shelves into sixteen
15¾” shelves - twelve for the upright sections
(7 on the left sides, 5 on the right side),
and four for the middle section.
1
¾” x 24” x48”
1 edge band white melamine
Cut two 4” x 15¾” strips for wall mount supports.
2
³/
16
” brass shelf pins
(12 per pack)
Zinc, plastic, and other styles and colors are available. Visit your
local Home Depot hardware aisle
for local options.
1
box
1
5
∕8” coarse thread all-purpose
or drywall screws
2
Phillips head screw cover white
(25 per pack)
Cover the screw heads and improve the appearance
of your project.
2
1” corner brace with screws
(4 per pack)
1
1¼” moulding round R/L
(fir or pine as available)
Cut round to 3’ length,
trim to 32” length for use as closet rod.
1 White closet pole socket Used to support closet rod.
www.roseburg.com or (800) 245-1115
RediShelf
Premium quality
melamine shelving,
furniture and
closet organizers.
•Thermallyfused
melamineprovides
durablesurface,
resistanttochips,
scratchesandstains
•Compatiblewith
mostshelf
mountinghardware
EASY TO ASSEMBLE
InstallationandCleaning
• To ensure clean cutting, use a fine-tooth carbide
tip blade. If using a circular saw, cut the exposed
side of the board face down; if using a handsaw,
cut the exposed side of the board face up. Put
masking tape on the cutline to reduce chip out
when cutting.
• We recommend drilling a pilot hole using a
3
∕32”
bit if you use no. 8 x 1-5/8” countersunk screws.
• Using plastic end caps to cover screws will
improve the appearance of your project.
• Use shelf pins in pre-drilled holes for the
shelves.
• Corner brackets are recommended instead of
screws for top shelves.
• Tall units must be secured to the wall by being
screwed into studs.
• Clean with warm water or a mild detergent. Do
not use abrasive cleaners or scouring powders.
Premium quality melamine shelving,
furniture and closet organizers.
MADE IN THE USA
48”Wide
Desk
Home Depot Material List 48” Wide Desk
QTY ITEM INSTRUCTIONS
4
¾” x 24” x 48” 1 edge band
white melamine
Use one full size panel for top. Out of one 24”
x 48” panel, cut one piece to 24” x 29¼” for an
upright panel, and the remainder to 18” for a
shelf. Repeat this step two more times for the two
remaining 24” x 48” panels so that you end up
with three upright panels and three shelves.
1
¾” x 24” x 48” 1 edge band
white melamine
Cut to 11¾” x 27¾” for the desktop brace.
1
box
1
5
∕8” coarse thread all-purpose
or drywall screws
2
1” corner brace with screws
(4 per pack)
Fasten the desktop to the upright panels using
corner braces.
1
¾” x 25’ white melamine iron-
on edge-banding
Follow manufacturer instructions to apply iron-on
melamine edge banding to any exposed panel
edges.
1
Phillips head screw cover white
(25 per pack)
Cover the screw heads and improve the appearance
of your project.
www.roseburg.com or (800) 245-1115
/