LCH655SSE
constantly check food frying to avoid that
the overheated oil may become a fire hazard.
1. 120mm to 125mm ducting adaptor
2. Ducting Adaptor
3. Chimney Flue Wall Bracket
4. Inner Chimney
5. Outside Chimney
6. Glass
7. Main Body
8. Filter
9. Screws Plug x 6
10. Washers x 2
11. Screws ST 4*35 x 6
ST 4*18 x 4
ST 4*10 x 2
cooker hood
cooker hood
cooker hood
cooker hood
cooker hood
cooker hood
Installation
Before beginning any installation work ensure
the mains power has been turned off.
Extracted Air Installation
1 Using a Phillips screwdriver fix the ducting
hose connector onto the air outlet of the hood.
Before installing the cooker hood, please first
fix the ducting adaptor on the airoutlet of the
hoods by 4 screws with their size of 18mm.
Note: 4 pcs of screws x 18mm
2 Connect the hose (not supplied) to the
air
duct. Use the adaptor provided to
connect
to a 125mm hose (not supplied).
3 The ducting can pass through your wall
to the outside.
Stencil
Use the stencil provided to help position the
hood onto the wall directly below the ducting.
NOTE: Take extreme care when drilling holes
into your wall to avoid hidden electrical wiring.
1 With the stencil positioned on the wall,
drill 4 holes onto the back wall. Push 4
raw plugs into the drill holes and partially
screw in the top 2 screws. (leaving 10mm
unscrew)
2 Fix the hood onto the wall by positioning
the upper 2 screws through the key holes
on the back of the hood.
3 Attach the lower part of the hood by
removing the filter panels to gain access
to the lower safety screw holes.
Attaching
the Chimney flue wall bracket
1 Using the wall bracket as a template, drill
2 holes into the wall and push raw plugs
into
the drill holes.
2 Place the wall bracket over the raw plugs
and
screw into position.
3 Screw the inner chimney flue section to the
wall
bracket.
Screws (4 x 10mm) : 2pcs
Washers: 2 pcs
Adjusting
the telescopic hood
The
telescopic chimney flue can be adjusted in
height
to fit your ceiling once fully attached to
the
wall.
3
Screws (4x35mm):4 pcs
Raw Plug: 4 pcs
Re-Circulation using Carbon filters
One carbon filter (not supplied) can also be
added to your cooker hood, when air is to
be re-circulated instead of external ducting.
Please see the Partmaster Direct details on the
back cover to order them - for UK only.
Installation
Control panel
0 = Switches the cooker hood off.
1 = Low speed. Is suitable when low levels of
steam are created whilst cooking.
2 = Medium speed.
3 = High speed. Is suitable when high levels
of steam are created whilst cooking.
= Switches the overhead light on.
The cooker hood should be left on for at least
15 minutes after cooking has finished to ensure
efficient filtering of the air.
Regular cleaning will help to maintain the
effectiveness of your cooker hood.
1 Switch off and unplug the cooker hood
before
cleaning.
2 Clean the inside and outside of the
cooker
hood with a damp cloth and a
mild
detergent.
NOTE:
Do not use solvents or abrasives as this
may
damage the cooker hood.
Warning:
Your cooker hood can become a
fire risk if it is not cleaned correctly
Cleaning
4
In Use
Please be careful when cleaning this appliance as
sheet metal can cause injury if not handled with case.
1. Remove the aluminum filter.
Insert the charcoal filter to
the inner slot.
The magnet inside carbon
filter will hold the filter in
position.
2. Re-install the aluminum filter.
To ensure the filters do not become a fire
hazard we recommend they are washed every
3 months. Do not check the filter panels whilst
the cooker hood is in use.
1 Before cleaning the filters always switch
off and disconnect the electrical suppl y.
2 Remove the filter panels by holding down
the buttons on each panel and lifting
towards you. They can then be taken out
of the cooker hood.
3
Wash filter in warm water and a
mild detergent, leave to soak and drain.
Ensure it is completely dry before
replacing into the cooker hood.
4 Place the bottom of panel into the
left or right side of the cooker hood
and raise the
other side to click into position.
NOTE: The filter panels are also dishwasher
proof. The filter panels may alter in colour
slightly after several washes, this is not a fault.
Cleaning the filters
Maintenance and Troubleshooting
5
Changing the internal light
Allow the cooker hood to cool for at least
30 minutes after use before changing the
light bulb.
1 Before carrying out the bulb replacement
always switch off and disconnect the
electrical supply.
The Cooker hood is not working
• Check it is plugged in and switched on.
• Check that the fuse in the plug has
not
blown.
• Plug in another appliance, such as a
lamp,
to see if the socket is working.
Servicing
Only
an authorised, qualified technician
should
perform repairs and maintenance of
the
appliance.
The power of bulb must not be more than 20W.
2 remove the lamp rim by turning anti -
clockwise
Take the fixed lamp rim off by unscrewing
it in an anti-clockwise direction.
Draw the old lamp out of the lamp holder,
insert the new lamp in the lamp holder.
Screw the fixed lamp rim tightly in a
clockwise direction.
3 Remove the bulb and replace with a new one.
4 Replace lamp rim by aligning the rib to slot in
unit and turn clockwise.
5 Make sure the rim is lock in position
6
Model
Rated Voltage 230
(V)
Rated Frequency 50
(Hz)
Rated Powe 180
(W)
Weigh 14.6
(kg)
Product Dimension
h/w/d 34x60x50
(cm)
Halogen
(G4, 12V)
2x20W max
Weight and Dimensions are approximate. Because we continually
strive
to improve our products we may change specifications and
designs
without prior notice.
Technical Specifications
MCH60SS cooker hood D4.qxd 9/29/05 4:39 PM Page 7
LCH655SSE
This symbol on the product or in the instructions means
that
your electrical and electronic equipment
should
be disposed at the end of its life separately from
your
household waste. There are separate collection
systems
for recycling in the EU.
For
more information, please contact the local authority or
your
retailer where you purchased the product.
Cod:XXXXXXXXXX
/