Logik LCH675SSE Instruction book

Model LCH675SSE

hood

6.Filter

7.Screws ST4*35 X5 ST4*18 X4

ST4*10 X2 ST3*10 X2

8.Washers x 2

9.Screw plug x 5

1.120mm to 125mm ducting adaptor

2.Ducting adaptor

3.Inner chimney

4.Outside chimney

5.Main body

Installation

Before beginning any installation work ensure

the mains power has been turned off.

Ducting

1 Using a Phillips screwdriver fix the ducting

hose connector onto the air outlet of the hood.

2 Connect the hose (not supplied) to the

air

duct. Use the adaptor provided to

connect

to a 125mm hose (not supplied).

(refer to fig.2)

3 The ducting can pass through your wall

to the outside.

4 If you operated the cooker hood in

recirculation mode, fit the metal plate in

the chimney to prevent the exhaust air

from reaching the ceiling.(refer to fig.2)

Stencil

Use the stencil provided to help position the

hood onto the wall directly below the ducting.

NOTE: Take extreme care when drilling holes

into your wall to avoid hidden electrical wiring.

1 With the stencil positioned on the wall,

drill 4 holes onto the back wall. Push 4

raw plugs into the drill holes and partially

screw in the top 2 screws. (Leaving 10mm

unscrew)

2 Fix the hood onto the wall by positioning

the upper 2 screws through the key holes

on the back of the hood.

3 Attach the lower part of the hood by

removing the filter panels to gain access

to the lower safety screw holes.

Attaching

the Chimney flue wall bracket

1 Using the wall bracket as a template, drill

2 holes into the wall and push raw plugs

into

the drill holes.

2 Place the wall bracket over the raw plugs

and

screw into position.

4 Screw the inner chimney flue section to the

wall

bracket by ST 4X10 screw.

Adjusting

the telescopic hood

The telescopic chimney flue can be adjusted in

height

to fit your ceiling once fully attached to

the

wall.

3

3 Screw the outer chimney to the unit.

Re-Circulation using Carbon filters.

Carbon filter (not supplied) can also be

added to your Cooker Hood, when air is to

be re-circulated instead of external ducting.

Please see Partmaster Direct details on the

back cover to order them - for UK only.

Installation

Control panel

The Cooker Hood should be left on for at least

15 minutes after cooking has finished to ensure

efficient filtering of the air.

Regular cleaning will help to maintain the

effectiveness of your cooker hood.

1 Switch off and unplug the cooker hood

before

cleaning.

2 Clean the inside and outside of the

cooker

hood with a damp cloth and a

mild

detergent.

NOTE:

Do not use solvents or abrasives as this

may

damage the Cooker Hood.

Cleaning

4

In Use

Please be careful when cleaning this appliance as

sheet metal can cause injury if not handled with case.

Carbon filter installation.

Carbon Filter.

There is slot on edge of carbon filter.

Remove the

external aluminum filter.

Insert the slot to the rid of inside air

vent opening.

Push the filter to lock in position.

Replace the external aluminum filter.

1.Timer control button ( ) : The timer is operated only

when the fan is turned on. When the fan is operationg,

press this button. The backlight around the button

starts flashing. The fan will turn off in about 15 minutes.

2.Fan On/Off button ( ) : Press this button to turn on

or off the fan.

3.Speed Control ( , ) : Press the ( ) to increase

the speed or press ( ) to dectease the fan speed.

The speed is indicated by the backlight of the button.

Speed

Soft

Low

Medium

High

BACKLIGHT: Flashing , OFF , ON

4.Lamp on/off ( ): Press this button to turn on or off

the lamp.

To ensure the filters do not become a fire

hazard we recommend they are washed every

3 months. Do not check the filter panels whilst

the Cooker Hood is in use.

1 Before cleaning the filters always switch

off and disconnect the electrical suppl y.

2 Remove the filter panels by holding down

the buttons on each panel and lifting

towards you. They can then be taken out

of the cooker hood.

3 Wash each filter in warm water and a

mild detergent, leave to soak and drain.

Ensure it is completely dry before

replacing into the Cooker Hood.

4 Place the bottom of each panel into the

back of the Cooker Hood and raise the

top to click into position.

NOTE: The filter panels are also dishwasher

proof. The filter panels may alter in colour

slightly after several washes, this is not a fault.

Cleaning the filters

Maintenance and Troubleshooting

5

3 Remove the lamp rim by unscrewing

the two screws.

5 Screw the fixed lamp rim tightly in a

clockwise directio

n.

4 Uncap the bulb and replace with a new

one.

6 Replace the filters.

Warning: Hold the bulb as it will drop

downwards

as it’s released.

Changing the internal light

Allow the cooker hood to cool for at least

30 minutes after use before changing the

light bulb.

1 Before carrying out the bulb replacement

always switch off and disconnect the

electrical supply.

2 To remove filters hold down buttons on

each panel and lift towards you.

The Cooker Hood is not working

• Check it is plugged in and switched on.

• Check that the fuse in the plug has

not blown.

• Plug in another appliance, such as a

lamp,

to see if the socket is working.

Servicing

Only an authorised, qualified technician

shoul

d perform repairs and maintenance of

th

e appliance .

6

Model

Rated Voltage 230

(V)

Rated Frequency 50

(Hz)

Rated Power 240

(W)

Weigh 18

(kg)

Product Dimension

h/w/d 37x60x50

(cm)

Halogen lamps 2x20W max

(K502 12V)

Weight and Dimensions are approximate. Because we continually

strive

to improve our products we may change specifications and

designs

without prior notice.

Technical Specifications

MCH60SS cooker hood D4.qxd 9/29/05 4:39 PM Page 7

LCH675SSE

This symbol on the product or in the instructions means

that

your electrical and electronic equipment

should

be disposed at the end of its life separately from

your

household waste. There are separate collection

systems

for recycling in the EU.

For

more information, please contact the local authority or

your

retailer where you purchased the product.

Cod:XXXXXXXXXX

Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories.

With over 1 million spares and accessories in stock we can deliver direct to your door the very

next day.

Visit www.partmaster.co.uk

or call

0870 6001 338

(UK customers only)

Calls charged at National Rate.

Logik LCH675SSE Instruction book

Logik LCH675SSE Instruction book

Related papers

Other documents