Invacare Silhouette Installation Instructions Manual

Brand: Invacare

Model: Silhouette

Type: Installation Instructions Manual

This manual is also suitable for

ContourU

Part No 1154276 1 ContourU™/ Silhouette™Seating Systems

ContourU™/ Silhouette™Seating Systems

NOTE:Che ckallpartsforshippingdamage.Incase ofshippingdamage, DONOTuse.Contact carrier/deal erforfurth er

instruction.

Safety Summary

Toensurethesafeinstalla tion,operationanduseoftheseat,theseins tructionsMUSTbe followed:

 WARNING

DO NOT use this product or any available optional equipment without first completely reading and

understanding these instructions and any additional instructional material such as owner’s manuals,

service manuals or instruction sheets supplied with this product or optional equipment. if you are

unable to understand the warnings, cautions or instructions, contact a healthcare professional, dealer

or technical personnel before attempting to use this equipment - otherwise, injury or damage may

occur

After any adjustments, repair or service and before use, make sure all attaching hardware is

tightened securely. Otherwise, injury or damage may occur.

If the seat and/or back does not fit the user properly, DO NOT use. Contact Invacare for proper

instruction, otherwise injury to the user may occur.

The best way to avoid problems related to pressure sores is to understand their causes and your role

in a skin management program.

Your therapist and physician should be consulted if you have any questions regarding weight relief,

self-examination of skin, or individual limitations and needs.

All cushions used for the prevention or treatment of decubitus ulcers (pressure sores) should be

selected carefully. Working with your therapist, physician and cushion supplier is the best way to

assure that a cushion choice matches your individual needs.

As the needs of the client become more complex, the cushion evaluation becomes more important.

Skin condition should be checked very frequently after the provision of any new seating system.

With regard to seat/chest positioning straps – it is the obligation of the DME dealer, therapists and

other healthcare professionals to determine if a seat/chest positioning strap is required to ensure the

safe operation of this equipment by the user. Serious injury can occur in the event of a fall from a

wheelchair.

Stabilize from the ground up. A stable base, pelvis and footrests are requirements for any torso

positioning system.

The position of back angle, rear wheels, seat depth and wheel locks are directly related to wheelchair

stability. Any change to one or any combination of the four may cause the wheelchair to decrease in

stability. Use extreme caution when using a new seating position.

ALWAYS make sure wheelchair is stable before reclining the back system. Refer to the Owner’s

Manual provided with the wheelchair.

To maintain the stability of the wheelchair when moving the rear wheels to ANY forward position,

the amount of recline MUST be limited to prevent the wheelchair from tipping onto the anti-tippers.

The necessary back angle MUST be selected before repositioning rear wheels forward.

 ACCESSORIES WARNING

Invacare products are specifically designed and manufactured for use in conjunction with

Invacare accessories. Accessories designed by other manufacturers have not been tested by

Invacare and are not recommended for use with Invacare products.

Installation Instructions

SAVE THESE INSTRUCTIONS

ContourU™/ Silhouette™Seating Systems 2 Part No 1154276

Product Description

TheseSeatingSystemsaredesignedtofitaspecificclientbasedonseatingandpositioningsimulation

performedontheShapeSensor.

ThisInstructionSheetprovidesinstallationinstructionsfortheContourUandSilhouetteSeatingSystems.

Dry Fitting the User

Followthedirection sintheShapeSensorManual(partnu mber0900117)todryfittheuser.

Use and Maintenance of the Seating System

Back Cover

ThecoverisproperlyinstalledwhenthewordsʺBOTTOMOFBACKʺ(markedoninsideofcov er)isatthe

bottomof theback.

Seat Cushion Cover

Thecoverisproperlyinstalled whenthezipperisatthebackofthecushion.Inaddition,thebacksurfaceof

thecushionismarked,“REAROFSEAT”.

Maintaining the Covers

Intheeventofincontinence,someleakagemayoccurattheseamstitching,fasteningstrapsoratthezipper ,

sothewaterrepellentcoatingshouldbecleaned.RefertoCleaning.

Inspection

NOTE:Inordertoensurethattheseatingsystemisworkingasdesigned,inspectionoftheseatingsystemonaregular

basisis necessary.

 WARNING

DO NOT continue to use this product if any deformation, corrosion, breakage, wear and or compres-

sion is found. Corrective maintenance can be performed at or arranged through your equipment sup-

plier.

V isuallyinspectallpartsweekly,includinghardware,upholsterymaterials,foams(ifaccessible),and

plasticsfordeformation,corrosion,breakage,wearand/orcompression.

Cleaning

NOTE:Weeklycleaningisr ecommended.

TheSeatingSystemisavailablewithseve raldifferentcovering options.Followwashinginstructions

attachedtocov er.

Keepallpartsdryandawayfromchemicalsorlubricants.

Tocleanthewaterrepellentfoamcoating,useasoftclothandwipecleanwithw armwaterandamildsoap

solution.Rinseoffanddry.

CAUTION

The cover is designed to protect the foam against a user’s incontinence and to provide fire retardation,

so the cushion must not be used without its cover. If the cover is torn, it must be replaced.

Part No 1154276 3 ContourU™/ Silhouette™Seating Systems

Installing Back Cane Hardware Assemblies

Kwik Fit Assemblies

NOTE:Forthispr ocedure,refertoFIGURE 1.

NOTE:TheKwikFitassembliesmustbeinstalledon

therearofthebackcanes.

1. Determinethediametertubingoftheback

canes(1‐inch,7/8‐inchor3/4‐inch).Referto

DetailʺBʺofFIGURE 1todeterminewhich

holestousewhenattachingthestrapstothe

clampblocks.

2. Securetwostrapstoonesideofeachclamp

blockwithtwopanheadscrews.

NOTE:Theotherendsofthestrapswillremainloose

untilSTEP5.

NOTE:Makesurethequick‐lockbracketswithlocking

tabsareinstalledtowardsthetopofthebackcanesas

showninDetail“A”ofFIGURE 1.

NOTE:Makesurethemountingbracketswithoutthe

lockingtabsareinstalledtowardsthebottomofthe

backcanesasshowninDetail“A”ofFIGURE 1.

3. Puttheclampblock/strapassemblyinplace

onthequick‐lockbracketormounting

bracket.Puttheassemblyinplaceontherear

ofthebackcane.

4. Wraptheloosestrapsaroundthebackcane.

5. Attachtheloosestrapstoclampblockwith

twopanheadscrews.

NOTE:Thesetscrewsintheclampblocksareusedto

securetheassembliestothebackcanes.

CAUTION

DO NOT overtighten the set screws.

Otherwise damage may occur.

6. Slidetheassemblytothedesiredpositionand

tightenthesetscrews.

7. RepeatSTEPS3‐6toattachtheotherthree

KwikFitassembliestothebackcanes.

8. Makesurethattheassembliesatthetopand

bottomoftheofthebackcanesarelinedup

horizontally.

FIGURE 1 Installing Back Cane Hardware

Assemblies - Kwik Fit Assemblies

Quick-lock Bracket

w/locking tab

Pan-head Screws

Mounting

Bracket

DETAIL “A” - KWIK FIT ASSEMBLIES

(MOUNT ON REAR OF BACK CANE)

Clamp Block

Straps

NOTE:Thisdrawingshowsthe

panheadscrewslineduptoattach

strapstotheclampblockarounda

1‐inchdiametercane.Todetermine

whichholestouse,referto

“DETAILB”.

Set Screws

Top and Front

of Back Cane

Bottom of Back Cane

Back Cane

Rear of Back Cane

DETAIL “B” - STRAP MOUNTING HOLES

1-inch diameter cane

7/8-inch diameter cane

3/4-inch diameter cane

ContourU™/ Silhouette™Seating Systems 4 Part No 1154276

HWBAK Assemblies

NOTE:Forthisprocedure,refertoFIGURE 2.

NOTE:TheHWBAKassembliesmustbemountedonthe

frontofthebackcanes.

1. Removethesnap‐lockclampsandsnap‐lock

clampbase sfromtheHWBAKkit.

2. Attachasnap‐lockclamptoeach snap‐lock

clampbase withtwoscrews.

3. Determinethediametertubingofthebackcanes

(1‐inch,7/8‐inchor3/4‐inch).RefertoDetailʺBʺ

ofFIGURE 2todeterminewhichholestouse

whenattachingthestrapstotheclampblocks.

4. Securetwostrapstoonesideoftheeachclamp

blockwithtw opanheadscrews.

NOTE:Theotherendsofthestraps willremainloose

untilSTEP7.

NOTE:Makesurethemountingbracketswithout

Snap‐Lockclampsareinstalledtowardsthetopoftheback

canesasshowninDetail“A”ofFIGURE 2.

NOTE:Makesurethemountingbracketswith

Snap‐Lockclampsareinstalledtowardsthebottomofthe

backca nesasshowninDetail“A”ofFIGURE 2.

5. Putthe clampblock/strapassemblyinplaceon

themountingbracketorsnap‐lock clampbase.

Puttheassemblyinplaceonthefrontoftheback

cane.

6. Wraptheloosestrapsaroundthebackcane.

7. Attachthe loosestrapstoclampblockwithtwo

panheadscrews.

NOTE:Thesetscr ewsin theclampblocks ar eusedto

securetheassembliestothebackcanes.

 CAUTION

DO NOT overtighten the set screws. Otherwise

damage may occur.

8. Slidetheassemblytothe desiredpositionand

tightenthesetscrews.

9. RepeatSTEPS5‐8toattachtheotherthree

HWBAKassembliestothebackcanes.

10. Makesurethattheassembliesatthetopand

bottomof theofthebackcanesarelinedup

horizontally.

FIGURE 2 Installing Back Cane Hardware

Assemblies - HWBAK Assemblies

DETAIL “A” - HWABK ASSEMBLIES

(MOUNT ON FRONT OF BACK CANE)

Threaded Holes

Clamp Base

Clamp Block

Snap-Lock

Clamp Base

Set Screws

Straps

NOTE:Thisdrawing

showsthepan‐headscrews

lineduptoattachstrapsto

theclampblockarounda

1‐inchdiametercane.To

determinewhichholesto

use,referto“DETAILB”.

Pan-head Screws

Front of Back Cane

Top and Front

of Back Cane

Back Cane

Bottom of Back Cane

Rear of Back Cane

DETAIL “B” - STRAP MOUNTING HOLES

1-inch diameter cane

7/8-inch diameter cane

3/4-inch diameter cane

Part No 1154276 5 ContourU™/ Silhouette™Seating Systems

Installing a Back on the Wheelchair

Determinewhichtypeof backandhardwareassemblieswillbeinstalledonyourwheelchair(KwikFitor

HWABK).

•IfinstallingaKwikFitback,refertoKwikFitAssembliesonpage 3andKwikFitBackonpage 5.

•IfinstallingaBackCushionPan,refertoHWBAKAssembliesonpage 4andBackCushionPanon

page 7.

•Ifinstallingawood‐mountedcushion,refertoHWBAKAssembliesonpage 4andWood‐mountedBack

Cushiononpage 8.

Kwik Fit Back

Installing the Adjustable Mounting Brackets to the Kwik Fit Back

NOTE:Forthispr ocedure,refertoFIGURE 3onpage6.

NOTE:ToattachtheKwikFitBacktothewheelchair,KwikFitassembliesmustbeinstalledonthebackcanes.Referto

KwikFitAssembliesonpage 3iftheKwikFitassemb liesarenotinplaceonyourwhee lchairbeforestartingthis

procedur e.

NOTE:Alwaysdeterminewher ethebackwillbepositionedinrelationtowheelchairfra meandseat cushionbefor e

attachingthebacktothewheelchair.

NOTE:Tomaintainthecenterofgravity(CG)ofthewheelchair user,theKwikFitbackwillbeplacedbetweenorbehind

theba ckcanes.

NOTE:If necessary,anoptionalmountingspacer(partnumber3002937)canbeusedtospaceouttheadjus table

mountingbracketsatthetopoftheKwik Fitback.

1. FollowtheproceduresintheShapeSensorOwner’sManualtodeterminewheretheKwikFitback will

attachtothewheelchairbackcanes.

CAUTION

DO NOT overtighten the set screws. Otherwise damage may occur.

2. Ifnecessary,adjustthepositionoftheKwikFitassembliesonthebackcanes.Tightenthesetscrews

whenadjustmentsarecomplete.

3. P ositiontheKwikFitbackonthewheelchairinthepositiondeterminedinSTEP1.

4. Determinethemountingpositionsofth efouradjustablemountingbrackets.Makenoteofwhich

holes

tous etobestfittheuser.

NOTE:RefertoDetailʺBʺofFIGURE 3forposition options.

5. Attachtheadjustablemountingbra cketguidetotheadjustablemountingbracketwith twosocketcap

screws.DO NOTtightenthesocketcapscrews.

6. Inserttheadjustablemountingbracketguideintotheslotonthesideofthe KwikFitbackandslidethe

bracketintothepositiondeterminedinSTEP3.Tightensocket capscrews.

7. RepeatSTEPS5and6toinstalltheotherthreeadjustablemountingbracke ts.

NOTE:Whe ninstalledproperly,ther ewillbetwoadjustablemo untingbracketsoneachsideof thewheelchair.

ContourU™/ Silhouette™Seating Systems 6 Part No 1154276

Installing the Kwik Fit Back

1. InstalltheKwikFitbackontotheadjustablemountingbracketsasshowninDetail“A ” ofFIGURE 3.

2. LocktheKwikFitbackintoplacebyclosingtheQuick‐Lockbracketsoneachsideofthewheelchair.

3. Checkforthe followingconditions:

•Theloc kleversontheQuick‐Lockbracketsopenandclosewithoutobstruction.

•TheKw ikFitbackhangslevel.

•TheKw ikFitbackdoesnot rattle.

4. AdjusttheKwikFitassembliesasnecessaryuntilallconditionsinSTEP3aremet.

FIGURE 3 Installing the Kwik Fit Back

Adjustable Mounting Bracket

Kwik Fit Back

DETAIL “A” - ADJUSTABLE MOUNTING BRACKET OPTIONS

Adjustable Mounting Bracket Guide

Slot in Kwik Fit Back

Socket Cap Screws

Extended Adjustable Mounting Bracket

Kwik Fit Back

Quick-Lock Bracket

TOOPEN‐FlipUP

TOCLOSE‐FlipDOWN

DETAIL “B” - INSTALLING THE KWIK FIT BACK ONTO THE WHEELCHAIR

Back Cane

NOTE:Thedashedlinesrepresentthebackcanerelativetotheadjustablemountingbracketposition.

Front of

wheelchair

Mounting Bracket

Part No 1154276 7 ContourU™/ Silhouette™Seating Systems

Back Cushion Pan

Installing the HWABK Back Brackets

NOTE:TheHWABKBackBracketsar eusedwithHWABKAssembliesthatattachtothebackcanes.RefertoHWBAK

Assembliesonpage 4iftheHWABKassembliesarenotinplace onyourwheelchairbeforestartingthisprocedur e.

NOTE:Forthispr ocedure,refertoFIGURE 4.

1. Putthe backcushionpanontothewheelchair

andmakenoteoftheholelocationsthatbestfit

theus er.

2. PuttheL‐bracketsonthe backcushionpanatthe

locationsdeterminedinSTEP1.

3. Puta2‐holebackingplateonthecushionsideof

thebackcushionpan.Attachth eL‐brackettothe

backcushionpanwithtwobuttonheadcap

screwsinstalledthroughtheseatpanandthe

2‐holebackingplate.Usethe5/32allen wrench

suppliedinthekittotightenthescrews.

4. RepeatSTEP 3toinstallthethreeremaining

L‐bracketsontothebackcushionpan.

5. Putthe backcushionpanontothewheelchair.

LineuptheL‐bracketswiththeclampbaseson

thebac kcanes.

6. Adjust/reclinethebackcushionpanuntilthe 

desiredback angleisreached.Makenoteofthe

holesintheL‐bracketsthatlineupwiththe 

clampbase satthedesiredangle.Removethe

backcushionpanfromthewheelchair.

7. Threadonestainlesssteelpinintoeach

L‐bracketintheholesdeterminedinSTEP6

usingthe9/64hexkeywrenchsuppliedinthe 

kit.

Installing the Back Cushion Pan

NOTE:Forthisprocedure,refertoFIGURE 5.

1. Putthe backcushionpanontothewheelchair.

Putthe topofthebackcushionpaninplacein

theclampbasesatthetopofthebackcanes.

2. Pushthebottomofth e

backcushionpantoward

theSnap‐lockclampsonthebottomoftheback

canes.Liftthebackcushionpanupabout

1/2‐inchandpushdownto“snap”thestainless

steelpinsinplaceintheSnap ‐lock clamps.

NOTE:Toremovethebackcushionpanfromthe

wheelchair,reverse

STEPS1and2.

FIGURE 4 HWBAK Back Brackets

FIGURE 5 Installing the Back Cushion Pan

“Short” L-bracket

Stainless Steel Pin

“Long” L-bracket

Button Head Cap Screws

2-hole

Backing Plate

Back Cushion Pan

TOP

BOTTOM

Stainless

Steel

Pins

L-Bracket

Snap-Lock

Clamp

Back

Cane

Clamp

Base

TOP

BOTTOM

ContourU™/ Silhouette™Seating Systems 8 Part No 1154276

Wood-mounted Back Cushion

Installing the Wood-mounted Back Cushion Hardware

NOTE:TheWood‐mountedBackCushi onBracketsareusedwithHWABKAssembliesthatattachtothebackcanes.

Referto HWBAKAssembliesonpage 4iftheHWABKassembliesarenotinplaceonyourwheelchairbefor e starting

thispr ocedur e.

1. Putthe backcushionontothewheelchair .

Determinethelocationsofth ebrackets.Mark

theholelocationsonthecushionwithapen or

marker.

NOTE:Whe ninstalledproperly,theL‐bracketswillline

uphor izontallyandvertically.Install theShort

L‐bracketsatthetopofthecushionandtheLong

L‐bracketsatthebottomof thecushion.

2. Drilltw omountingholesinthebackcushionfor

eachL‐bracketwitha11/32drillbit.

3. UsingaM6hexkeywrench,screwathreaded

insertintoeachofthebracketmountingholes.

CAUTION

DO NOT overtighten the threaded inserts.

Damage to the cushion may result.

4. AttachtheL‐bracketstothebackcushionwith

twobuttonhead capscrews.Usethe5/32allen

wrenchsuppliedinthekittotightenthescrews.

5. Putthe backcushionontothewheelchair .Line

upth eL‐bracketswiththeclampbasesonthe

backcanes.

6. Adjust/reclineth ebackcushion

untilthedesired

backangleisreached.Makenoteof theholes in

theL‐bracketsthatlineupwiththeclampbases

atthedesiredangle.Remov e thebackcushion

fromthewheelchair.

7. Threadonestainlesssteelpinintoeach

L‐bracketintheholesdeterminedinSTEP6

usingthe9/64hexkeywrenchsuppliedinthe 

kit.

FIGURE 6 Wood-mounted

Back Cushion Hardware

Installing the Wood-mounted Back Cushion

1. Putthe stainlesssteelpinsintheShortL‐brac ketsontotheclampbases.

2. Pushthebottomofth ebackcushion towardtheSnap‐lockclampsonthebottomofthebackcanes.Lift

thebackcushionpanupabout

1/2‐inchandpushdownto“snap”thestainlesssteelpins inplaceinthe

Snap‐lock clamps.

NOTE:Toremovethewood‐mountedbackcushionfromthewheelchair,reverseSTEPS1and2.

Short

L-bracket

Stainless

Steel Pin

Long

L-bracket

Threaded

Inserts

Button Head

Cap Screws

Stainless

Steel Pin

Threaded

Inserts

Button Head

Cap Screws

Wood-mounted

Back Cushion

TOP

BOTTOM

Part No 1154276 9 ContourU™/ Silhouette™Seating Systems

Installing a Seat onto the Wheelchair

Determinewhichtypeof seatandmountinghardwarewillbeusedonyourwheelchair.

•Ifinstallingawoodmountboard,RefertoAttachingaWoodMountBoardtotheWheelchairSeatRails.

•Ifinstallingaseatpan,refertoAttachingaSeatPantotheWheelchairSeatRailsonpage 10.

Attaching a Wood Mount Board to the Wheelchair Seat Rails

NOTE:Forthisprocedure,refertoFIGURE 7.

1. Putthewoodmountboardontothewheelchair

seatrails.

2. Determinethemountinglocationsofthe

brackets.Marktheholelocationsontheboard

withapenormarker.Removetheboardfrom

thewheelchair.

NOTE:Wheninstalledproperly,themounting

bracketswillnotinterfere

withanyotherwheelchair

parts.

3. Drilltw omountingholesintheboardforeach

bracketwitha11/32drillbit.

4. UsingaM6hexkeywrench,screwathreaded

insertintoeachofthebracketmountingholes.

CAUTION

DO NOT overtighten the threaded inserts.

Damage to the cushion may result.

5. Foreachmountingbracket,plac ethelany ard

anddetentassemblyononeofthesockethead

capscrews.

6. Ateachlocation,attachthemountingbracketto

theboardwithtwosockethea dcapscrews.

FIGURE 7 Attaching a Wood Mount Board to the

Wheelchair Seat Rails

Wood Mount Board

Socket Head Cap Screws

Mounting

Bracket

Threaded Inserts -

DO NOT overtighten

Lanyard and

Detent Pin Assembly

TOP

BOTTOM

ContourU™/ Silhouette™Seating Systems 10 Part No 1154276

Attaching a Seat Pan to the Wheelchair Seat Rails

NOTE:Forthisprocedure,refertoFIGURE 8.

1. Putthe seatpanontothewheelchairseatrails

andmakenoteoftheholelocationsthatbestfit

theus er.

2. Removetheseatpanfromthewheelchair.

NOTE:Wheninstalledproperly,themounting

bracketswillnotinterferewithanyotherwheelchair

parts.

3. Putthebrackets ontheseatrails attheloca tions

determinedin STEP1.

NOTE:Whenpositionedproperly,theprotrudingpins

onthebracketswillalignwiththeoutermostholeson

thecornersoftheseatpan.

4. Putthe seatpanonthemountingbrackets.

5. Adjustthebracketsasnecessaryuntilthe

protrudingpin sprotrudethroughoneofthe 

outermostseatpanholes.

NOTE:Usetheinnermostholestoattachthebrackets

totheseatpan.

6. Insertacapscrewthroughoneoftheinnermost

holesoftheseatpanandthroughthemounting

holeofthebracket.Putahexnut ontothecap

screw.DONOTtightenthehexnut.

7. Fromunderneaththeseatpan,insertthedetent

pinth roughtheholesinthebracket.

NOTE:Usetheinnermostholestoattachthelanyard

totheseatpan.Makesuretoattachthelanyardcloseto

themountingbracket.

8. Attachthelanyardtotheseatpan

withacap

screwandhexnut.

9. Tightenthehexnuts.

10. RepeatSTEPS6and9ateachbracketlocation.

FIGURE 8 Attaching a Seat Pan to the Wheelchair

Seat Rails

Outermost Row

of Holes

Innermost Row

of Holes

Bracket

Protruding Pin

(insert through a hole

in the outermost row)

Seat Pan

Cap Screws

(insert through

holes in the

innermost row)

Lanyard

Detent Pin

(insert in the direction show)

Hex

Nut

Hex Nut

TOP

BOTTOM

Part No 1154276 11 ContourU™/ Silhouette™Seating Systems

Installing the Seat Cushion

NOTE:Forthisprocedure,refertoFIGURE 9.

Thecushionattachestowheelchairseatupholsteryusinghookandloopfastenersonthebottomof

cushioncover.

1. Determinewhetherthewheelchairseatingsurfacehashookorloopattachmentstrips.

2. Performoneofthefollowing:

•Ifwheelchairhasloopattachmentstrips,verifythatdoublesidedhookstripsaresecurely

attachedtotheloopattachmentstripsonthebottomofthecushion.

•Ifthewheelchairhashookattachmentstrips,removethedoublesidedhookstripsfromthe

cushion.

NOTE:Ifthewheelchairseatingsurfacehasneitherhookorloopattachmentstrips,removethedoublesidedhook

fromthebottomofthecover.

3. Alignthefrontedgeofthecushionwiththefrontedgeofseatingsurface.

 WARNING

Make sure the cushion is securely fastened to the wheelchair seating surface with the hook and

loop fasteners before using. Exercise caution when transferring in and out of the wheelchair,

especially if the wheelchair is not equipped with hook and loop fasteners.

4. Securecushiontotheseatingsurface,makingsurethatthehookandloopfastenersaresecurely

attachedtotheseatingsurfaceandthecushion.

NOTE:Ifthewheelchairseatingsurfacehasneitherhookorloopattachmentstrips,removethedoublesidedhook

fromthebottomofthecover.

FIGURE 9 Installing the Seat Cushion

Seat

Cushion

Seating

Surface

LIMITED WARRANTY

PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW

APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.

This warranty is extended only to the original purchaser/user of our products.

This warranty gives you specific legal rights and you may also have other legal rights which vary from state to

state.

Invacare warrants its product to be free from defects in materials and workmanship for the period of two years of

use by original purchaser except for the cover, which is warranted for a period of 90 days of use by the original

purchaser. If within such warranty period any such product shall be proven to be defective, such product shall be

repaired or replaced, at Invacare's option. This warranty does not include any labor or shipping charges incurred

in replacement part installation or repair of any such product. Invacare's sole obligation and your exclusive

remedy under this warranty shall be limited to such repair and/or replacement.

For warranty service, please contact the dealer from whom you purchased your Invacare product. In the event

you do not receive satisfactory warranty service, please write directly to Invacare at the address on the back

cover. Provide dealer's name, address, model number, and the date of purchase, indicate nature of the defect and,

if the product is serialized, indicate the serial number.

Invacare Corporation will issue a return authorization. The defective unit or parts must be returned for warranty

inspection using the serial number, when applicable, as identification within thirty days of return authorization

date. DO NOT return products to our factory without our prior consent. C.O.D. shipments will be refused; please

prepay shipping charges.

LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL

NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED, PRODUCTS

SUBJECT TO NEGLIGENCE, ACCIDENT, IMPROPER OPERATION, MAINTENANCE OR STORAGE,

COMMERCIAL OR INSTITUTIONAL USE, PRODUCTS MODIFIED WITHOUT INVACARE'S EXPRESS

WRITTEN CONSENT INCLUDING, BUT NOT LIMITED TO, MODIFICATION THROUGH THE USE OF

UNAUTHORIZED PARTS OR ATTACHMENTS; PRODUCTS DAMAGED BY REASON OF REPAIRS MADE

TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE, OR TO A PRODUCT

DAMAGED BY CIRCUMSTANCES BEYOND INVACARE'S CONTROL, AND SUCH EVALUATION WILL BE

SOLELY DETERMINED BY INVACARE. THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING

FROM NORMAL WEAR OR FAILURE TO ADHERE TO THESE INSTRUCTIONS.

THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES

WHATSOEVER, WHETHER EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND THE SOLE REMEDY FOR

VIOLATIONS OF ANY WARRANTY WHATSOEVER, SHALL BE LIMITED TO REPAIR OR REPLACEMENT

OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN, THE APPLICATION

OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION OF THE

EXPRESS WARRANTY PROVIDED HEREIN. INVACARE SHALL NOT BE LIABLE FOR ANY

CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER.

THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/PROVINCIAL LAWS AND

REQUIREMENTS.

Invacare Corporation

www.invacare.com

USA

One Invacare Way

Elyria, Ohio USA

44036-2125

Canada

570 Matheson Blvd. E Unit 8

Mississauga Ontario

L4Z 4G4 Canada

identified by the symbols ™ and ®. All

trademarks are owned by or licensed to

Invacare Corporation unless otherwise

noted.

For customer service call: Part No 1154276

1-800-451-3553 Rev A - 5/08

Invacare Silhouette Installation Instructions Manual

Brand: Invacare

Model: Silhouette

Type: Installation Instructions Manual

This manual is also suitable for

ContourU

Download PDF

report

Invacare Silhouette Installation Instructions Manual

This manual is also suitable for

Invacare Silhouette Installation Instructions Manual

Related papers

Other documents