American Gas Lamp Works GLM 900 User manual

Brand: American Gas Lamp Works

Model: GLM 900

Type: User manual

MODELS GLM #900, 1000, 1200, 1400, & 1600

POST MOUNT

FOR OUTDOOR USE ONLY

7” Water Column for Natural Gas

11” Water Column for LP(Propane)

ACCESSORIES PACKED

IN BOTTOM OF BOX

THE LAMP HEAD MUST BE INSTALLED TO CONFORM WITH LOCAL CODES OR IN ABSENCE OF LOCAL

CODES WITH THE ANSI Z223.1 – LATEST EDITION, CAN1-B149.1 OR CAN 1-B149.2

THE MINIMUM CLEARANCE FROM COMBUSTIBLE CONSTRUCTION IS 12” TOP BY 6” SIDE

POST INSTALLATION;

1. Obtain from your dealer 3” OD X 7’9” post with notches for valve access at top.

2. Install inside post (1/4” OD) refrigeration type copper tubing with ¼” flare nuts at each end. Tubing

should be coiled 2 ½ times at top.

3. Tubing should protrude about 5” through hole at bottom of post.

4. If supplied, insert ladder rest through hole and attach ornamental ball to each end.

5. Dig a hole 21” deep X 12” wide.

6. Attach the ¼” flare nut at bottom of post to gas supply.

7. Secure post in plumb position and pour concrete around post to just below the level of the line access hole.

LAMP INSTALLATION

1. Connect gas supply line to tubing with the ¼” flare nuts at the base of the post and tighten flare nuts

clockwise. No sealants are necessary.

2. Install screen, rain cap and finial for models 1200, 1400, & 1600. The screen is to be inside the top of the

roof.

3. Attach gas valve to ¼” flare nut on copper tubing.

4. Lower lamp onto post, aligning valve with slot in top of post. Check! Make sure hole is lined up with the

valve stem.

5. Tighten set screw(s) in collar of lamp so lamp is well secured to post.

6. Install glass by fitting top edge into frame top and pressing glass against tabs inside of frame and allowing

it to slide into bottom frame. (Install all but one panel)

7. Be certain the lamp valve is in the OFF position before turning on the main gas supply line.

8. Leaving lamp valve in OFF position, turn on main gas supply and check all connections for leaks using a

soapy solution. NEVER USE AN OPEN FLAME TO CHECK FOR GAS LEAKS! Tighten any leaky

connections and recheck for leaks.

9. Install mantles (instructions on back)

10. Install last panel of glass.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. If odor continues, immediately

call gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or

other flammable vapors and

liquids in the vicinity of this or

any other gas appliance.

INSTALLER: Leave instructions with the appliance for the consumer to retain for future reference

MAINTENANCE INSTRUCTIONS:

No combustible material, gasoline or other flammable vapors or liquids should be stored near lamp. Nothing should

obstruct the flow of combustion and ventilation air. Occasionally the glass will need to be cleaned with household glass

cleaner and mantles should be visually checked, for condition and burn, replacement mantles if necessary (refer to the

lighting instructions). Gas lamp parts and mantles (inverted, soft auto form or hard inverted mantles) are available from

your local gas appliance dealer or:

AMERICAN GAS LAMP WORKS

101 HOEVELER ST

SPRINGDALE, PA 15144

(Toll Free) 855-427-5483

CAUTION

!!!!!!!!!!!TURN GAS SUPPLY OFF AND WAIT FOR LAMP TO COOL BEFORE STARTING ANY REPAIRS

MOVE AND CLEAN GLASS AND REPLACE BROKEN MANTLES AS NECESSARY

STEP #1

Remove one glass panel by lifting glass from bottom

Corners with forefingers pulling forward slightly and

Lowering.

STEP #2

Install mantle over ceramic nozzle do not touch fabric just place

mantle on nozzle. With gas turned off hold a lighted match up to but

not touching mantle to burn off protective coating.

STEP #3

Using a screwdriver in the lower collar of lamp to reach valve, turn

gas on – light mantle with match being careful not to touch mantle.

It is very fragile after being burnt.

STEP #4

Replace glass by fitting top edge into frame top. Pressing glass

against tabs inside of frame and allowing glass to slide into bottom

frame.

STEP #5

Using a screwdriver adjust flame with on – off valve to its brightest

But containing flame within mantle.

American Gas Lamp Works GLM 900 User manual

Brand: American Gas Lamp Works

Model: GLM 900

Type: User manual

Download PDF

report

American Gas Lamp Works GLM 900 User manual

American Gas Lamp Works GLM 900 User manual

Other documents