P.O. Box 455, Leeds, AL 35094-0455
Phone: 205-699-2411
Fax 205-699-7603
NOTE: Because Hubbell has a policy of continuous product improvement, we reserve the
right to change design and specifications without notice.
©
Copyright 2003 Hubbell/Anderson
Manual M-8232
(5-01)
SERVICE AND
OPERATION
MANUAL
MODEL VC-350R & VC6-350R-SN
HYDRAULIC REMOTE TOOL HEAD
Manual M-8232
(5-01)
®
ANDERSON
POWER SYSTEMS, INC.
®
ANDERSON
POWER SYSTEMS, INC.
i
TABLE OF CONTENTS
Nib and Nest Changeout (3 Nib Arrangement)
VC6-350R and VC6-350R-SN...........................................................1
Nib and Changeout (Nest Die Arrangement VC6-350R)..........................2
General ....................................................................................................3
Specifications ...........................................................................................3
Service Instructions
Care of Hydraulic Tools......................................................................4
Cleaning the Tool Head .....................................................................4
Periodic Shop Maintenance...............................................................4
Operating Instructions ..............................................................................5
Installation of Sleeve Connectors (Three nib Arrangement) ..............6
Installation of U-Groove Connectors (Three Nib Arrangement).........6
Installation of H-Frame Connectors
(“D” or “O” Die Arrangement) VC6-350R .......................................7
Installation of Full Tension Sleeves
(“O” Die Arrangement) VC6-350R..................................................8
Overhaul Instructions
Disassembly
Tool Head .......................................................................................9
Ram Unit ........................................................................................9
Assembly
Ram Unit ......................................................................................10
Tool Head .....................................................................................10
Tools Required for Overhaul ..................................................................10
Instructions for Returning Tools..............................................................10
Troubleshooting Guide........................................................................... 11
Parts List ................................................................................................13
Exploded View Drawing .........................................................................15
WARNING: This tool head is not for use on energized lines
without use of non-conductive accessories. Failure to com-
ply with this warning could result in serious injury or death.
WARRANTY: This tool is warranted for one (1) year from
date of purchase. Proof of purchase date is required for
warranty claims. Obvious misuse or abuse voids warranty.
The use of this tool in a manufacturing process renders
this warranty null and void.
1 2
VC6-350R & VC6-350R-SN
NIB AND NEST CHANGEMOUT
THREE NIB ARRANGEMENT
For three nib operation, lock latch pin in outward position (counter-
clockwise).
VC6-350R VC6-350R-SN
VC6-350R NIB AND NEST CHANGEMOUT
NEST DIE ARRANGEMENTS
NOTE: For nest die operation, lock latch pin in inserted position (counter-
clockwise).
1. Install nest die as shown (See
“Operation Instructions” on
page 5).
2. Bring side jaws together, pin
and lock. CAUTION: Make
sure pin is fully inserted and
locked before crimping.
3. To release side jaws, unlock,
pull pin out and turn to locked
position (counterclockwise).
3
4
GENERAL
This tool is designed to apply VERSA-CRIMP or VERSAtile fittings to cop-
per, aluminum and ACSR conductors. The basic connector configurations
are:
Lug
for
VC6-350R and
VC6-350R-SN
Sleeve
for
VC6-350R and
VC6-350R-SN
Open Groove
for
VC6-350R and
VC6-350R-SN
“H” FRAME
for
VC6-350R
VC6-350R VC6-350R-SN
5 6
VC6-350R VC6-350R-SN
VC6-350R VC6-350R-SN
7 8
VC6-350R
VC6-350R
9
10
11 12
13 14
15
/