PIR A-BEDEXIT--01-LED Bed Exit PIR Single & Dual Models User manual

Type
User manual

This manual is also suitable for

See the video Tutorial at https://safelife.com.au/product/dual-bed-exit-pir/
INSTRUCTION MANUAL (with in-line monitor)
Bed Exit PIR Single & Dual Models
Model: A-BEDEXIT-PIR-01 -LED & 05 (January 2010)
Safe Life 03 - 9588 0392
Available from www.safelife.com.au
See the video Tutorial at https://safelife.com.au/product/dual-bed-exit-pir/
Model: A-BEDEXIT-PIR-01-LED Model: A-BEDEXIT-PIR-05-LED
Introduction:
Once set up correctly the Bed Exit PIR will detect as a resident swings thier legs over the side
of the bed breaking the invisible PIR beam. This invisible beam is designed to tapper down
ending at the base of the bed. This will allow a carer to move freely around the bed without
generating an alarm. If the PIR beam protrudes past the bottom of the bed and this is a
problem, lower the PIR a centremetre or two on the wall at the head of the bed. Extra
brakets are available making it easy to move the system from one room to another leaving
the bracket on the wall for future use.
Set up procedure:
1. Mount the wall mount bracket on the wall at the head of the bed
10cm out from the bed and 40cm off the floor (as shown).
TIP: Its a good idea to use Blue Tack and test before fixing the bracket to
the wall. If the PIR beam protrudes past the bottom of the bed this is a
problem lower the PIR a centermetre or two on the wall. Follow the same
procedure if you If you have a dual system, one on each side of the bed.
2. Connect the power pack to the 240V power point and the 6.3mm
connector to the nurse call point. You can use a double adaptor at the
nurse call point so a pendant cord can also be used. Double adaptors
are are available from the SafeLife website.
3. Turn the power on at the power point and as the PIR calabrates the red LED on the
PIR will flash for a duration of one minute. When the led stops flashing the PIR is ready to use.
For best results do not stand in the way of the PIR as it calabrates. The system will remain
powered up and is turned ON and OFF at the lin-line switch. The green LED indicated the
sensor is ON.
4. When the PIR Beams are set up correctly and the system is switched on, as a resident
attempts to exit the bed the PIR beam is broken and the nurse call point is activated alerting
care staff.
See the video Tutorial at https://safelife.com.au/product/dual-bed-exit-pir/
5. Configuring the 6.3mm plug for your brand nurse call system:
Unless otherwise requested the system is supplied as a mono configuration. (stereo wired as
mono) and this will usually work on most nurse call systems.
If your sytem requires Tip & Ring or Tip & Sleeve this can easily be achieved by removing the 4
screws and taking the back of the in-line monitor to remove a lug. For Tip and Ring remove
the lug on “S” for sleeve. For Tip and Sleeve remove the lug on “R” for ring.
As a general rule mono will work on many systems and there will be no re-configuration
required.
If the your nursecall system bell press cord also has a light switch on it, a Tip and Ring or Tip
and Sleeve confighuration will be required.
Sometimes over time some different brands have also used different configurations so a little
bit of trial an error may be required.
General Configurations with different brands
Smart Caller Tip and Ring
Questek Tip and Ring
Care Tech Tip and Ring
Xacom Tip and Ring
Advance Care Tip and Sleeve
Austco Tip and Sleeve
If your nurse call syetem bedside call point does not have a 6.3mm size plug contact us and
will provide an alternative plug.
6. Disclaimer
The supplier has no control or means of surveillance in relation to the installation, set up and
continuous on-going reliable operation of the product. While the products available at Safe
Life can assist in the supervised care of a person, these devices shall not be considered as life
saving devices. Safe Life accepts no liability for the loss of property or personal injury, loss of
income or any other liability that should result from a device failing to operate.
  • Page 1 1
  • Page 2 2

PIR A-BEDEXIT--01-LED Bed Exit PIR Single & Dual Models User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI