Omnivision OX03J10 User guide

Category
Security cameras
Type
User guide
OX03J10
3 megapixel product brief
The OX03J10 is a 3MP high-sensitivity CMOS SoC for human
vision and machine vision automotive applications, including
360° surround view display systems, rear view cameras and
camera monitoring systems (CMS). It uniquely offers
simultaneous 140 dB HDR and industry-leading LED flicker
mitigation along with the best low light performance
available.
The OX03J10 features 1920 x 1536 resolution in 1/2.4-inch
optical format. The OX03J10 comes in the industry smallest
a-CSP™ package. Size and cost are reduced due to the
integration of the image signal processor with the sensor
together in one SoC.
The OX03J10 features OMNIVISION’s PureCel®Plus
technology and uses a 3 µm Deep Well™ split pixel. It outputs
YUV and RAW simultaneously. It is ASIL-C compliant.
Find out more at www.ovt.com.
140 dB HDR with LED Flicker Mitigation Together in
One SoC for Automotive Cameras
OX03J10
Applications
active array size: 1920 x 1536
maximum image transfer rate:
30 fps @ 1920 x 1536 (combined HDR
in YUV422/RGB888 + 16/14/12-bit
(PWL) raw combined HDR)
power supply:
- analog: 3.3V
- digital: 1.1V
- I/O pins: 1.8V or 3.3V
power requirements:
- active: 560 mW (streaming
1920 x 1536 @ 30 fps typical)
output interfaces:
up to 4-lane MIPI CSI-2
temperature range:
operating: -40°C to +105°C
sensor ambient temperature and
-40°C to +125°C junction temperature
lens size: 1/2.44"
for 1920 x 1536 image size
lens chief ray angle: 21.79°
output formats: combined HDR in
YUV422/RGB888 + 16/14/12-bit (PWL)
raw combined HDR, uncompanded 24-bit
or 20/16/14/12-bit (PWL) raw combined
HDR
pixel size: 3.0 µm x 3.0 µm
image area: 5808 µm x 4656 µm
resolution: 1920 x 1536
and cropped sizes
high dynamic range
high sensitivity
dual conversion gain
ASIL-B safety compliant
image signal processing functions:
- AEC/AGC/AWB
- lens correction
- defective pixel correction
- HDR combination
- tone mapping
- automatic black level correction
supported output formats:
- YUV
- RGB888
- RAW
OX03J10-E76Y-001A-Z (RGGB, lead-free)
76-pin a-CSP™, rev 1A, packed in tray without protective film
supports LED flickering mitigation
(LFM) function
supports aiming function
SPI master for overlay and
loading settings
distortion correction
50/60 Hz flicker cancellation
SCCB for register access
programmable GPIOs
high speed serial data transfer
with MIPI CSI-2
external frame synchronization capability
embedded temperature sensor
one-time programmable (OTP) memory
Technical Specifications
Functional Block Diagram
Product Features
Ordering Information
Version 1.0, December 2022
4275 Burton Drive
Santa Clara, CA 95054
USA
Tel: + 1 408 567 3000
Fax: + 1 408 567 3001
www.ovt.com
OMNIVISION reserves the right to make changes to their products or to discontinue any
product or service without further notice. OMNIVISION and the OMNIVISION logo are
trademarks or registered trademarks of OmniVision Technologies, Inc. PureCel is a
registered trademark of OmniVision Technologies, Inc. a-CSP and Deep Well are
trademarks of OmniVision Technologies, Inc. All other trademarks are the property of
their respective owners.
automotive
- 360° surround view system
- rear view camera
- camera monitoring system (CMS)
OX03J10
sensor core image
processor
output
interface
column
sample
& hold
row select
PLL’s
control registers
timing generator and
system control
reference
generator
SCCB slave
interface SPI / UART
MDP/N[3:0]
MCP/MCN
temperature
sensor
pixel
array AMP 10-bit
ADC
FIFO
MIPI
+ + +
BLC
- --
ISP
MCU
AEC
AGC
ADRC
XI/XVCLK
XO
RESETB
FSIN
TM
SPICK
MOSI
SPI2/UTX
SPI3/URX
SSN
VMERRB
VSYNC
ERRB
GPIO[5:0]
VH2
VH1
VN2
VN1
MISO
SIOC
SID
SIOD
  • Page 1 1
  • Page 2 2

Omnivision OX03J10 User guide

Category
Security cameras
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI