John Adams 1110X User manual

Type
User manual

John Adams 1110X Aqua Gelz Standard lets you create your own colorful 3D gel creations. Choose a character mold, fill it with colored gel, and submerge it in the solution tank. Your creation will release from the mold in 10-30 seconds and continue to firm up in the solution. Once it's firm, transfer it to a container of water or the Aqua Gelz Deluxe Playset's display tank. Your creation will remain soft and squishy as long as it's kept in water.

John Adams 1110X Aqua Gelz Standard lets you create your own colorful 3D gel creations. Choose a character mold, fill it with colored gel, and submerge it in the solution tank. Your creation will release from the mold in 10-30 seconds and continue to firm up in the solution. Once it's firm, transfer it to a container of water or the Aqua Gelz Deluxe Playset's display tank. Your creation will remain soft and squishy as long as it's kept in water.

SIDE 1
(2) Choose a character mould. To prepare
it for gel and ensure easy gel release, give it a
quick dunk into the Solution, lift out, tap &
shake off excess solution.
(3) Start your creation by gently twisting the Gelz
cap counter-clockwise to open, and then squeezing
the coloured gel into your character mould. It is
recommended to not over fill the mould past the top
edge of the mould. When done, be sure to close
each gel by gently twisting cap clock-wise.
NOTE: AFTER YOU GENTLY TWIST TO OPEN CAP,
DO NOT PULL CAP OFF.
(4) Place the Gel-filled mould into the Solution tank
once again, this time submersing it completely. While
submersed in the solution, wiggle your mould side to side
gently until your character releases from the mould. It will
release in 10-30 seconds. Once creation releases from
the mould let it remain in the solution tank until it firms. Be
gentle touching the Creation during the firming process.
(5) Test your Creation by gently squeezing it from time to
time. Once your creation has reached the desired firmness,
transfer it into another container filled with only plain clean
water or Display Fish Tank (Aqua Gelz Deluxe Playset only).
The firming process will stop once taken out of the Solution.
It’s time to have hours of fun playing with your new creation.
NOTE: Always store your creation in water or it will harden
and shrink. DO NOT throw away your Solution or Solution
Tray as both can be reused again and again. Store in a safe
location and cover when not in use. When reusing the
solution Do not add more water. To make a new batch of
Solution start with Step 1 & follow the Solution Mixing
Chart.
1
2
4
5
NOTE: Your Solution can be reused over
and over. Store in a safe location and cover.
Do not add more water when reusing or the
effectiveness will be reduced.
NOTE: For a softer creation remove from Solution
sooner. For a firmer character leave in Solution longer.
If Creation is not firm enough it can be placed back
into Solution until desired firmness is reached.
(1) Start your new creation by adding the correct
amount of Solution Mix and clean water to the reusable
clear solution tray on back side of package. SEE MIXING
CHART for correct amounts of water and Solution Mix
needed. If the indicated proportions of water and Solution
Mix are not followed the Solution will not work properly. Stir
until the Solution Mix is completely dissolved in the water.
Solution
Tray
Starter
Pack:
Creation
Station:
Solution
Tray
Display
Tray
Deluxe
Set:
Solution
Tray:
DO NOT DISCARD
REUSABLE TRAYS:
Solution
Mixing Chart
250 ml
Fresh Water
+
1x 5g
Solution Mix
Packet
Solution Tray
IMPORTANT
For proper forming of creations it is
necessary to follow the chart above
DISPOSAL: Prepared Aqua Gelz Solution can be poured down a sink drain. Solution Mix, Gel or creations can be
disposed of in ordinary household garbage.
ATTENTION: Avoid getting coloured Gelz on clothing, carpet, furniture or walls. If contact occurs wash immediately
with detergent and water. Gel which is allowed to dry may stain.
Avoid contact with eyes and do not swallow content. This is not a food product. If ingestion takes place immediately
see medical advice. In case of eye contact rinse with clean water and immediately seek medical advice.
Do not place Solution, Gelz, or creations in ears or nose. If any part of this toy becomes lodged in nose or ears
immediately seek medical advice.
Do not use the product when there is a risk of contacting wounds or broken/damaged skin. Discontinue use if
redness or itching occurs on contact with skin. If symptoms persist contact a doctor.
© 2021 Zoinks™. All rights reserved. ZOINKS™ LTD., 12/F King Palace Plaza
No. 55 King Yip Street, Kwun Tong, Kowloon Hong Kong. Patent Pending and
Copyright Granted. For inquiries email us at [email protected] or visit us at
www.zoinksasia.com. Product color and styles may vary. Please retain
Instructions and packaging for future reference.
01142021
3A
B
C
!
Before
Starting:
Under the cap of each Gelz squeeze
bottle is a sealing plug which must
be removed prior to use. Unscrew
the Gelz bottle cap, remove plug
and dispose of in household trash
and replace cap on the bottle.
Instruction
Guide
Distributed by John Adams Leisure Ltd., PE28 4YA, England.
EU authorised representative: John Adams Leisure EU Ltd.,
D06 H685, Ireland. For customer services call 01480 414361 or
To see more of our range visit www.johnadams.co.uk
WARNING! Not suitable for children under 36 months. Choking hazard –
contains small parts. Avoid contact with eyes and do not swallow content.
This is not a food product. Adult supervision required.
1110X_01_AQUAGELZ_GENERIC_INS_PRT02 280521
Date: 1.14.2021
PO No: 20444
PI No: 0024 / 2021
Product Name: Aqua Gelz Standard
Instruction Guide
Customer: John Adams Leisure Ltd.
FINAL ARTWORK
Approved by: Ruth Marlow
  • Page 1 1

John Adams 1110X User manual

Type
User manual

John Adams 1110X Aqua Gelz Standard lets you create your own colorful 3D gel creations. Choose a character mold, fill it with colored gel, and submerge it in the solution tank. Your creation will release from the mold in 10-30 seconds and continue to firm up in the solution. Once it's firm, transfer it to a container of water or the Aqua Gelz Deluxe Playset's display tank. Your creation will remain soft and squishy as long as it's kept in water.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI