RS-TOUCH SERIES
IN-SESSION
COMMON
SETTINGS
SETUP GUIDE
24/7 TECHNICAL SUPPORT AT 1.877.877.2269 OR VISIT BLACKBOX.COM
24/7 TECHNICAL SUPPORT AT 1.877.877.2269 OR VISIT BLACKBOX.COM
DOUBLE-HINGED
CABINET, PLEXIGLASS
WINDOW DOOR, M6
RAILS
WMD12-2125-PQE, WMD19-2125-PQE, WMD25-2125-PQE
USER MANUAL
This manual is provided to prevent service personnel from committing an act that results in the risk of fire, electric
shock, or personal injury. Only trained service personnel should receive, unpack, and assemble a Black Box wall mount
cabinet. In addition, only trained service personnel should install equipment in wall mount cabinets..
This manual provides general safety guidelines to be observed during installation, operation, and maintenance of the
Black Box wall mount cabinet.
WARNING:
Failure to follow directions in the warning could result in personal injury or loss of life.
CAUTION:
Failure to follow directions in the caution could result in damage to equipment or storage data.
SAFETY CONSIDERATIONS
WARNING:
Improper handling and use of the Black Box wall mount cabinet could result in equipment damage, serious injury,
or possible death.
Only trained service personnel should be used to remove the wall mount cabinet from its packaging. Also, verify that
you have a sucient number of service personnel. Do not attempt to move a wall mount cabinet by yourself.
Be sure to read and follow all individual manufacturer equipment manuals for safety and installation instructions.
Proper spacing is required when installing electrical equipment to avoid electrical shock. Maintain minimum spacing
between the accessories; components, and the wall mount cabinet for safe equipment operation when installed in
accordance with the current National Electrical Code ANSI/NFPA.
The ambient temperature operating range for the Black Box wall mount cabinet and accessories is 50 to 95° F
(10 to 35° C).
The non-operating temperature is -4 to +140° F (-20 to +60° C).
21.877.877.2269 Blackbox.com
PREFACE
NEED HELP?
LE AVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1. 8 7 7. 87 7. 2 2 6 9
3
1.877.877.2269 Blackbox.com
PRODUCT PHOTOS
NEED HELP?
LE AVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1. 8 7 7. 87 7. 2 2 6 9
PRODUCT PHOTOS
WMD12-2125-PQE
FRONT VIEW
WMD12-2125-PQE
BACK VIEW
WMD12-2125-PQE
SIDE VIEW
WMD19-2125-PQE
FRONT VIEW
WMD25-2125-PQE
FRONT VIEW
4
RECEIVING AND UNPACKING
Inspect and report any damage before receiving. Unpack the wall mount cabinet by carefully removing the corrugated carton and
corners.
Avoid damaging the wall mount cabinet when removing packaging.
WARNING:
Only trained service personnel should be used to unpack and move the wall mount cabinet. Also, verify that you
have a sucient number of service personnel. Do not attempt to move a wall mount cabinet by yourself.
MOUNTING INSTRUCTIONS
Once the location on the wall has been determined, inspect the wall surface. The wall must be flat and square in the
horizontal and vertical plane to ensure that the wall mount closes correctly. If the wall is not flat and square, the use
of shims may be required.
NOTE:
Installer is responsible for determining the appropriate hardware necessary based upon the installation surface.
WARNING:
Only install equipment after the wall mount cabinet has been properly secured. Do not move the wall mount
assembly while loaded.
To maintain a uniform distribution of the mechanical load in the wall mount cabinet, load the heaviest equipment
first at the bottom of the wall mount cabinet. Then load the lighter units at the top. Rated or maximum load
capacities for the wall mount cabinets appear in the specification section on the next page.
1.877.877.2269 Blackbox.com
INSTALLATION PREPARATION
NEED HELP?
LE AVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1. 8 7 7. 87 7. 2 2 6 9
5
Part Number Height
(inches)
Width
(inches)
Depth
(inches)
RMU Weight. Capacity.
(lb.)
WMD12-2125-PQE 24 21.3 24.5 12 150
WMD19-2125-PQE 36 21.3 24.5 19 250
WMD25-2125-PQE 48 21.3 24.5 25 350
1.877.877.2269 Blackbox.com
PACKAGE CONTENTS
(1) Wall mount cabinet
(2) Pair of SILVER keys - key number “333”
(1) Bag of mounting hardware (50) M6 cage nuts and screws
(4) Black Bars and (8) screws 10-32 for the bars
SPECIFICATIONS
SPECIFICATIONS
NEED HELP?
LE AVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1. 8 7 7. 87 7. 2 2 6 9
6
POWER AND GROUNDING
WARNING:
To avoid injury to persons or loss of life, ground each cabinet individually to the dedicated branch circuit ground.
Connecting Main Protective Grounding Stud to the Dedicated Branch Circuit Ground
Connect the dedicated branch circuit ground connector to the main protective grounding stud located inside the
cabinet on the back of the rear section and inside the cabinet on the side using a listed ring or closed-loop terminal.
Connecting Main Protective Grounding Stud to the Protective Bonding Conductors
Connect the middle wall mount frame on the cabinet to the main protective grounding stud located inside the
cabinet on the back of the rear section using a listed ring or closed-loop terminal.
Parts Not Bonded to Protective Earthing Terminal
The rails are not effectively bonded to the protective earthing terminal. If these parts need to be bonded to the
protective earthing terminal, do so in accordance with Article 250 of the National Electrical Code.
1.877.877.2269 Blackbox.com
POWER AND GROUNDING
NEED HELP?
LE AVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1. 8 7 7. 87 7. 2 2 6 9
7
INSTALLATION PROCEDURE
1. Mounting holes are designed for 3/8" hardware, 16" on center.
2. Use the template on the shipping box to locate your mounting holes.
3. To adjust mounting rails, use ⁄ socket or wrench to loosen ¼-20 carriage bolts and nuts (multiple locations on the
rail, dependent upon height); slide rail to desired location and tighten hardware.
SECTION E-E
RIGHT SIDE VIEW
A
E
E
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
FRONT VIEW
(without Door)
FRONT VIEW
(with Door)
BOTTOM VIEW
ISO COLLAPSED
(without Door)
ISO VIEW OPENED
19.17
21.25
18.31 TO
HEIGHT
10.63
12.00
7.386.50
16.00 TO
2.55
1.50
MTG HOLES
PART No. HEIGHT DEPTH USABLE DEPTH MAX. RAIL SPACING RMU WEIGHT CAPACITY MTG HOLES
GL2418WM 24.00" 18.00" 16.0" 11.06" 12 150 LBS 19.00"
GL24WM 24.00" 24.50" 22.0" 17.62" 12 150 LBS 19.00"
GL36WM 36.00" 24.50" 22.0" 17.62" 19 250 LBS 31.00"
GL48WM 48.00" 24.50" 22.0" 17.62" 25 300 LBS 21.50" (3 LOCATIONS)
INDEPENDENT LOCKING FRONT
AND REAR DOOR SECTION
MOUNTING HOLES FOR
3/8" HARDWARE
SPECIFICATIONS: WM WALL MOUNT
RACK SPACES: 19" EIA 310-E COMPLIANT - SEE CHART FOR RMU
COLOR: DURABLE BLACK TEXTURED POWDER COAT.
FEATURES: 2 PAIR OF FULLY ADJUSTABLE #12-24 THREADED MOUNTING RAILS, #12 GA.
1, 2, AND 3" CODUIT AND HORSESHOE KNOCKOUTS ON TOP AND BOTTOM OF REAR SECTION.
SOLID STEEL OR PLEXIGLASS DOORS.
FULL PIANO HINGE PROVIDES ADDED STRENGTH FOR REAR SECTION.
DUST KIT AVAILABLE.
CENTER SWING-OUT SECTION PROVIDES FRONT/REAR ACCESS TO CABLES.
REVERSIBLE CABINET FOR LEFT OR RIGHT HAND SWING-OUT.
WEIGHT TESTED TO 1/2" OF DEFLECTION.
OPTIONAL FRONT DOOR INSERTS
SOLID STEEL PANEL - 24WDX03
PERFORATED STEEL PANEL - MESH24WS
PLEXI PANEL - PLEX24WS
.63
.63
.50
RMU
3.50
DEPTH
MAX RAIL SPACING
USABLE DEPTH
SECTION E-E
RIGHT SIDE VIEW
A
E
E
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
FRONT VIEW
(without Door)
FRONT VIEW
(with Door)
BOTTOM VIEW
ISO COLLAPSED
(without Door)
ISO VIEW OPENED
19.17
21.25
18.31 TO
HEIGHT
10.63
12.00
7.386.50
16.00 TO
2.55
1.50
MTG HOLES
PART No. HEIGHT DEPTH USABLE DEPTH MAX. RAIL SPACING RMU WEIGHT CAPACITY MTG HOLES
GL2418WM 24.00" 18.00" 16.0" 11.06" 12 150 LBS 19.00"
GL24WM 24.00" 24.50" 22.0" 17.62" 12 150 LBS 19.00"
GL36WM 36.00" 24.50" 22.0" 17.62" 19 250 LBS 31.00"
GL48WM 48.00" 24.50" 22.0" 17.62" 25 300 LBS 21.50" (3 LOCATIONS)
INDEPENDENT LOCKING FRONT
AND REAR DOOR SECTION
MOUNTING HOLES FOR
3/8" HARDWARE
SPECIFICATIONS: WM WALL MOUNT
RACK SPACES: 19" EIA 310-E COMPLIANT - SEE CHART FOR RMU
COLOR: DURABLE BLACK TEXTURED POWDER COAT.
FEATURES: 2 PAIR OF FULLY ADJUSTABLE #12-24 THREADED MOUNTING RAILS, #12 GA.
1, 2, AND 3" CODUIT AND HORSESHOE KNOCKOUTS ON TOP AND BOTTOM OF REAR SECTION.
SOLID STEEL OR PLEXIGLASS DOORS.
FULL PIANO HINGE PROVIDES ADDED STRENGTH FOR REAR SECTION.
DUST KIT AVAILABLE.
CENTER SWING-OUT SECTION PROVIDES FRONT/REAR ACCESS TO CABLES.
REVERSIBLE CABINET FOR LEFT OR RIGHT HAND SWING-OUT.
WEIGHT TESTED TO 1/2" OF DEFLECTION.
OPTIONAL FRONT DOOR INSERTS
SOLID STEEL PANEL - 24WDX03
PERFORATED STEEL PANEL - MESH24WS
PLEXI PANEL - PLEX24WS
.63
.63
.50
RMU
3.50
DEPTH
MAX RAIL SPACING
USABLE DEPTH
18.31 C-to-C
FRONT VIEW WITHOUT DOOR
FRONT VIEW WITH DOOR
21.25
19.17
VARIES
10.63
Use latch supplied in hardware bag,
when horseshoe knockout is used
Rear section
1", 2" and 3" nominal
concentric conduit
knockouts and horseshoe
knockouts; top and bottom rear
section
Continuous Hinges on front
door and rear section
Front door
Provision for optional 2 fan assembly
Center swing section
19" EIA mounting rails;
2 pairs of M6 rails
Independent
locking front door
and rear section
1.877.877.2269 Blackbox.com
INSTALLATION
NEED HELP?
LE AVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1. 8 7 7. 87 7. 2 2 6 9
8
SECTION E-E
RIGHT SIDE VIEW
A
E
E
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
FRONT VIEW
(without Door)
FRONT VIEW
(with Door)
BOTTOM VIEW
ISO COLLAPSED
(without Door)
ISO VIEW OPENED
19.17
21.25
18.31
TO
HEIGHT
10.63
12.00
7.386.50
16.00 TO
2.55
1.50
MTG HOLES
PART No. HEIGHT DEPTH USABLE DEPTH MAX. RAIL SPACING RMU WEIGHT CAPACITY MTG HOLES
GL2418WM 24.00" 18.00" 16.0" 11.06" 12 150 LBS 19.00"
GL24WM 24.00" 24.50" 22.0" 17.62" 12 150 LBS 19.00"
GL36WM 36.00" 24.50" 22.0" 17.62" 19 250 LBS 31.00"
GL48WM 48.00" 24.50" 22.0" 17.62" 25 300 LBS 21.50" (3 LOCATIONS)
INDEPENDENT LOCKING FRONT
AND REAR DOOR SECTION
MOUNTING HOLES FOR
3/8" HARDWARE
SPECIFICATIONS: WM WALL MOUNT
RACK SPACES: 19" EIA 310-E COMPLIANT - SEE CHART FOR RMU
COLOR: DURABLE BLACK TEXTURED POWDER COAT.
FEATURES: 2 PAIR OF FULLY ADJUSTABLE #12-24 THREADED MOUNTING RAILS, #12 GA.
1, 2, AND 3" CODUIT AND HORSESHOE KNOCKOUTS ON TOP AND BOTTOM OF REAR SECTION.
SOLID STEEL OR PLEXIGLASS DOORS.
FULL PIANO HINGE PROVIDES ADDED STRENGTH FOR REAR SECTION.
DUST KIT AVAILABLE.
CENTER SWING-OUT SECTION PROVIDES FRONT/REAR ACCESS TO CABLES.
REVERSIBLE CABINET FOR LEFT OR RIGHT HAND SWING-OUT.
WEIGHT TESTED TO 1/2" OF DEFLECTION.
OPTIONAL FRONT DOOR INSERTS
SOLID STEEL PANEL - 24WDX03
PERFORATED STEEL PANEL - MESH24WS
PLEXI PANEL - PLEX24WS
.63
.63
.50
RMU
3.50
DEPTH
MAX RAIL SPACING
USABLE DEPTH
TOP/BOTTOM VIEW
2 fan unit mounting shown
1", 2", and 3" rear section
nominal concentric conduit
knockouts
6.50
7.38
SECTION E-E
RIGHT SIDE VIEW
A
E
E
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
FRONT VIEW
(without Door)
FRONT VIEW
(with Door)
BOTTOM VIEW
ISO COLLAPSED
(without Door)
ISO VIEW OPENED
19.17
21.25
18.31
TO
HEIGHT
10.63
12.00
7.386.50
16.00 TO
2.55
1.50
MTG HOLES
PART No. HEIGHT DEPTH USABLE DEPTH MAX. RAIL SPACING RMU WEIGHT CAPACITY MTG HOLES
GL2418WM 24.00" 18.00" 16.0" 11.06" 12 150 LBS 19.00"
GL24WM 24.00" 24.50" 22.0" 17.62" 12 150 LBS 19.00"
GL36WM 36.00" 24.50" 22.0" 17.62" 19 250 LBS 31.00"
GL48WM 48.00" 24.50" 22.0" 17.62" 25 300 LBS 21.50" (3 LOCATIONS)
INDEPENDENT LOCKING FRONT
AND REAR DOOR SECTION
MOUNTING HOLES FOR
3/8" HARDWARE
SPECIFICATIONS: WM WALL MOUNT
RACK SPACES: 19" EIA 310-E COMPLIANT - SEE CHART FOR RMU
COLOR: DURABLE BLACK TEXTURED POWDER COAT.
FEATURES: 2 PAIR OF FULLY ADJUSTABLE #12-24 THREADED MOUNTING RAILS, #12 GA.
1, 2, AND 3" CODUIT AND HORSESHOE KNOCKOUTS ON TOP AND BOTTOM OF REAR SECTION.
SOLID STEEL OR PLEXIGLASS DOORS.
FULL PIANO HINGE PROVIDES ADDED STRENGTH FOR REAR SECTION.
DUST KIT AVAILABLE.
CENTER SWING-OUT SECTION PROVIDES FRONT/REAR ACCESS TO CABLES.
REVERSIBLE CABINET FOR LEFT OR RIGHT HAND SWING-OUT.
WEIGHT TESTED TO 1/2" OF DEFLECTION.
OPTIONAL FRONT DOOR INSERTS
SOLID STEEL PANEL - 24WDX03
PERFORATED STEEL PANEL - MESH24WS
PLEXI PANEL - PLEX24WS
.63
.63
.50
RMU
3.50
DEPTH
MAX RAIL SPACING
USABLE DEPTH
REAR VIEW
3.50
Mounting holes for 3/8" hard-
ware
1", 2", and 3" rear section
nominal concentric conduit
knockouts
Mounting Holes
19", 31" and 21.50
(3)"
2.55
1.50
16.00 C to C
1.877.877.2269 Blackbox.com
INSTALLATION
NEED HELP?
LE AVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1. 8 7 7. 87 7. 2 2 6 9
NEED HELP?
LE AVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1. 8 7 7. 87 7. 2 2 6 9
9
1.877.877.2269 Blackbox.com
APPENDIX A: REGULATORY INFORMATION
A. ROHS
This product is RoHS compliant.
NEED HELP?
LE AVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1. 8 7 7. 87 7. 2 2 6 9
APPENDIX A: REGULATORY INFORMATION
10 1.877.877.2269 Blackbox.com
A. NOM STATEMENT
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano
mojado o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el
fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de
operación. Todo otro servicio deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato
eléctrico sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en
libreros o gabinetes que impidan el flujo de aire por los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor,
estufas u otros aparatos (incluyendo amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de
operación, o como se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos
colocados sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del
aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de
tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios
de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato;o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
11
1.877.877.2269 Blackbox.com
NEED HELP?
LE AVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1. 8 7 7. 87 7. 2 2 6 9
APPENDIX B: DISCLAIMER/TRADEMARKS
B. DISCLAIMER
Black Box Corporation shall not be liable for damages of any kind, including, but not limited to, punitive, consequential
or cost of cover damages, resulting from any errors in the product information or specifications set forth in this
document and Black Box Corporation may revise this document at any time without notice.
B. TRADEMARKS USED IN THIS MANUAL
Black Box and the Black Box logo type and mark are registered trademarks of Black Box Corporation.
Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1. 8 7 7.8 7 7. 2 269
© Copyright 2022. BLACK BOX corporation. All rights reserved.
WMD12-2125-PQE_WMD19-2125-PQE_WMD25-2125-PQE_user_rev1.pdf
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Black Box WMD12-2425-PQU User manual
-
Black Box EMS1G48 Installation guide
-
-
Blackbox EMS10G12 Installation guide
-
-
-
-
-
-