Pentair 011075 User guide

Category
Above ground pool accessories
Type
User guide

Pentair 011075, an IntelliFlo3 VSF variable speed and flow pump, offers advanced pool management capabilities. Its intelligent programming optimizes energy usage and provides quiet operation. With built-in automation features, you can customize pump speed and flow to suit your pool's specific needs, saving energy and money.

Pentair 011075, an IntelliFlo3 VSF variable speed and flow pump, offers advanced pool management capabilities. Its intelligent programming optimizes energy usage and provides quiet operation. With built-in automation features, you can customize pump speed and flow to suit your pool's specific needs, saving energy and money.

IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
USER'S GUIDE
PENTAIR HOME
FOR INTELLIFLO3™ VSF AND INTELLIPRO3™ VSF
VARIABLE SPEED AND FLOW PUMPS
Des copies numériques de tous les manuels
IntellFlo3 VSF, ainsi que les versions traduites,
peuvent être trouvées sur www.pentair.com, ou
en scannant le code QR fourni.
Guide d'installation et d'entretien (P/N 357974)
Guide d'utilisation (P/N 357972)
Se pueden encontrar copias digitales de
todos los manuales de IntelliFlo3 VSF,
así como versiones traducidas en www.
pentair.com, o escaneando el código QR
proporcionado.
Guía de instalación y servicio (P/N 357973)
Guía del usuario (P/N 357971)
Digital copies of all IntelliFlo3 VSF manuals,
as well as translated versions, can be found
at www.pentair.com, or by scanning the
provided QR code.
Install and Maintenance Guide (P/N 356231)
User's Guide (P/N 356088)
i
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety
precautions should always be followed, include the following:
FAILURE TO FOLLOW ALL INSTRUCTIONS AND
WARNINGS CAN RESULT IN SERIOUS BODILY
INJURY OR DEATH. THIS PUMP SHOULD BE INSTALLED AND SERVICED
ONLY BY A QUALIFIED POOL SERVICE PROFESSIONAL. INSTALLERS,
POOL OPERATORS AND OWNERS MUST READ THESE WARNINGS AND
ALL INSTRUCTIONS IN THE OWNER’S MANUAL BEFORE USING THIS
PUMP. THESE WARNINGS AND THE OWNER’S MANUAL MUST BE LEFT
WITH THE POOL OWNER.
Do not permit children to use this product.
RISK OF ELECTRICAL SHOCK. Connect only to
a branch circuit protected by a ground-fault circuit-
interrupter (GFCI). Contact a qualied electrician if you cannot verify that the
circuit is protected by a GFCI.
This unit must be connected only to a supply circuit
that is protected by a ground-fault circuit-interrupter
(GFCI). Such a GFCI should be provided by the installer and should be
tested on a routine basis. To test the GFCI, push the test button. The GFCI
should interrupt power. Push the reset button. Power should be restored.
If the GFCI fails to operate in this manner, the GFCI is defective. If the
GFCI interrupts power to the pump without the test button being pushed, a
ground current is owing, indicating the possibility of an electric shock. Do
not use this pump. Disconnect the pump and have the problem corrected by
a qualied service representative before using.
This pump is for use with permanent swimming pools
and may also be used with hot tubs and spas if so
marked. Do not use with storable pools. A permanently-installed pool is
constructed in or on the ground or in a building such that it cannot be readily
disassembled for storage. A storable pool is constructed so that it is capable
of being readily disassembled for storage and reassembled to its original
integrity.
General Warnings
Never open the inside of the drive motor enclosure. There is a capacitor
bank that holds a 230 VAC charge even when there is no power to the
unit.
The pump is not submersible.
The pump is capable of high ow rates; use caution when installing and
programming to limit pumps performance potential with old or questionable
equipment.
Code requirements for electrical connection differ from country to
country, state to state, as well as local municipalities. Install equipment
in accordance with the National Electrical Code and all applicable local
codes and ordinances.
Before servicing the pump; switch OFF power to the pump by disconnecting
the main circuit to the pump.
This appliance is not intended for use by persons (including children) of
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning the use of the appliance by a person responsible for their
safety.
SUCTION ENTRAPMENT HAZARD: STAY OFF
THE MAIN DRAIN AND AWAY FROM ALL SUCTION
OUTLETS!
THIS PUMP IS NOT EQUIPPED WITH SAFETY VACUUM
RELEASE SYSTEM (SVRS) PROTECTION AND DOES NOT PROTECT
AGAINST BODY OR LIMB ENTRAPMENTS, DISEMBOWELMENTS (WHEN
A PERSON SITS ON A BROKEN OR UNCOVERED POOL DRAIN) OR HAIR
ENTANGLEMENTS.
THIS PUMP PRODUCES HIGH LEVELS OF SUCTION AND CREATES A
STRONG VACUUM AT THE MAIN DRAIN AT THE BOTTOM OF THE BODY
OF WATER. THIS SUCTION IS SO STRONG THAT IT CAN TRAP ADULTS
OR CHILDREN UNDER WATER IF THEY COME IN CLOSE PROXIMITY TO
A DRAIN OR A LOOSE OR BROKEN DRAIN COVER OR GRATE.
THE USE OF UNAPPROVED COVERS OR ALLOWING USE OF THE POOL
OR SPA WHEN COVERS ARE MISSING, CRACKED OR BROKEN CAN
RESULT IN BODY OR LIMB ENTRAPMENT, HAIR ENTANGLEMENT, BODY
ENTRAPMENT, EVISCERATION AND/OR DEATH.
The suction at a drain or outlet can cause:
Limb Entrapment: When a limb is sucked or inserted into an opening resulting
in a mechanical bind or swelling. This hazard is present when a drain cover
is missing, broken, loose, cracked or not properly secured.
Hair Entanglement: When the hair tangles or knots in the drain cover, trapping
the swimmer underwater. This hazard is present when the ow rating of the
cover is too small for the pump or pumps.
Body Entrapment: When a portion of the body is held against the drain
cover trapping the swimmer underwater. This hazard is present when the
drain cover is missing, broken or the cover ow rating is not high enough for
the pump or pumps.
Evisceration/Disembowelment: When a person sits on an open pool
(particularly a child wading pool) or spa outlet and suction is applied directly
to the intestines, causing severe intestinal damage. This hazard is present
when the drain cover is missing, loose, cracked, or not properly secured.
Mechanical Entrapment: When jewelry, swimsuit, hair decorations, nger,
toe or knuckle is caught in an opening of an outlet or drain cover. This hazard
is present when the drain cover is missing, broken, loose, cracked, or not
properly secured.
NOTE: ALL SUCTION PLUMBING MUST BE INSTALLED IN ACCORDANCE
WITH THE LATEST NATIONAL AND LOCAL CODES, STANDARDS AND
GUIDELINES.
This is the safety alert symbol. When you see this
symbol on your system or in this manual, look for
one of the following signal words and be alert to the
potential for personal injury.
Warns about hazards that can cause death, serious
personal injury, or major property damage if ignored.
Warns about hazards that may cause death, serious
personal injury, or major property damage if ignored.
Warns about hazards that may or can cause minor
personal injury or property damage if ignored.
NOTE Indicates special instructions not related to
hazards.
Carefully read and follow all safety instructions in this manual and on
equipment. Keep safety labels in good condition; replace if missing or
damaged.
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
IMPORTANT NOTICE
This guide provides installation and operation instructions for this pump.
Consult Pentair with any questions regarding this equipment.
Attention Installer: This guide contains important information about the
installation, operation and safe use of this product. This information should
be given to the owner and/or operator of this equipment after installation or
left on or near the pump.
Attention User: This manual contains important information that will help you
in operating and maintaining this product. Please retain it for future reference.
F
ii
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
Warning Page P/N 352557 Rev. D 11/19
IMPORTANT SAFETY INSTRUCTIONS
HAZARDOUS PRESSURE: STAND CLEAR OF PUMP
AND FILTER DURING START UP.
Circulation systems operate under high pressure. When
any part of the circulating system (i.e. locking ring, pump,
lter, valves, etc.) is serviced, air can enter the system
and become pressurized. Pressurized air can cause the
pump housing cover, lter lid, and valves to violently
separate which can result in severe personal injury or death. Filter tank lid and
strainer cover must be properly secured to prevent violent separation. Stand
clear of all circulation system equipment when turning on or starting up pump.
Before servicing equipment, make note of the lter pressure. Be sure that
all controls are set to ensure the system cannot inadvertently start during
service. Turn off all power to the pump. IMPORTANT: Place lter manual air
relief valve in the open position and wait for all pressure in the system
to be relieved.
Before starting the system, fully open the manual air relief valve and place
all system valves in the “open” position to allow water to ow freely from the
tank and back to the tank. Stand clear of all equipment and start the pump.
IMPORTANT: Do not close lter manual air relief valve until all pressure
has been discharged from the valve and a steady stream of water
appears. Observe lter pressure gauge and be sure it is not higher than the
pre-service condition.
General Installation Information
All work must be performed by a qualied service professional, and must
conform to all national, state, and local codes.
Install to provide drainage of compartment for electrical components.
These instructions contain information for a variety of pump models and
therefore some instructions may not apply to a specic model. All models
are intended for use in swimming pool applications. The pump will function
correctly only if it is properly sized to the specic application and properly
installed.
Pumps improperly sized or installed or used in
applications other than for which the pump was
intended can result in severe personal injury or death. These risks may
include but not be limited to electric shock, re, ooding, suction entrapment
or severe injury or property damage caused by a structural failure of the
pump or other system component.
The Virginia Graeme Baker (VGB) Pool and Spa Safety Act creates
new requirements for owners and operators of commercial swimming
pools and spas.
Commercial pools or spas constructed on or after December 19, 2008,
shall utilize:
(A) A multiple main drain system without isolation capability with suction
outlet covers that meet ASME/ANSI A112.19.8a Suction Fittings for Use in
Swimming Pools, Wading Pools, Spas, and Hot Tubs and either:
(i) A safety vacuum release system (SVRS) meeting ASME/ANSI
A112.19.17 Manufactured Safety Vacuum Release systems (SVRS) for
Residential and Commercial Swimming Pool, Spa, Hot Tub, and Wading
Pool Suction Systems and/or ASTM F2387 Standard Specication for
Manufactured Safety Vacuum Release Systems (SVRS) for Swimming
pools, Spas and Hot Tubs or
(ii) A properly designed and tested suction-limiting vent system or
(iii) An automatic pump shut-off system.
Commercial pools and spas constructed prior to December 19, 2008, with a
single submerged suction outlet shall use a suction outlet cover that meets
ASME/ANSI A112.19.8a and either:
(A) A SVRS meeting ASME/ANSI A112.19.17 and/or ASTM F2387, or
(B) A properly designed and tested suction-limiting vent system, or
(C) An automatic pump shut-off system, or
(D) Disabled submerged outlets, or
(E) Suction outlets shall be recongured into return inlets.
TO MINIMIZE THE RISK OF INJURY DUE TO
SUCTION ENTRAPMENT HAZARD:
A properly installed and secured ANSI/ASME A112.19.8 approved anti-
entrapment suction cover must be used for each drain.
Each suction cover must be installed at least three (3’) feet apart, as
measured from the nearest point to nearest point.
Regularly inspect all covers for cracks, damage and advanced weathering.
If a cover becomes loose, cracked, damaged, broken or is missing,
replace with an appropriate certied cover.
Replace drain covers as necessary. Drain covers deteriorate over time
due to exposure to sunlight and weather.
Avoid getting hair, limbs or body in close proximity to any suction cover,
pool drain or outlet.
Disable suction outlets or recongure into return inlets.
The pump can produce high levels of suction within
the suction side of the plumbing system. These high
levels of suction can pose a risk if a person comes within the close proximity
of the suction openings. A person can be seriously injured by this high level
of vacuum or may become trapped and drown. It is absolutely critical that the
suction plumbing be installed in accordance with the latest national and local
codes for swimming pools.
A clearly labeled emergency shut-off switch for the pump
must be in an easily accessible, obvious place. Make
sure users know where it is and how to use it in case of emergency.
Pumps and replacement motors that are single speed and one (1)
Total HP or greater cannot be sold, offered for sale, or installed in a
residential pool for ltration use in California, Title 20 CCR sections
1601-1609.
For Installation of Electrical Controls at Equipment
Pad (ON/OFF Switches, Timers and Automation
Load Center)
Install all electrical controls at equipment pad, such as
on/off switches, timers, and control systems, etc. to allow
the operation (startup, shut-down, or servicing) of any
pump or lter so the user does not place any portion
of his/her body over or near the pump strainer lid, lter lid or valve closures.
This installation should allow the user enough space to stand clear of the lter
and pump during system start-up, shut down or servicing of the system lter.
iii
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .............
INTRODUCTION .....................................................
Home Dashboard
INITIAL SETUP .......................................................
Create a Pentair Home Account
Pairing Devices to your Account
OPERATION ...........................................................
Pump Dashboard
Program Setup
Device Settings
Relays
Direct Connect
Priming Parameters
Limits Parameters
Thermal Mode
TROUBLESHOOTING ............................................
Troubleshooting Chart
Alarms and Warnings
i
1
1
2
2
3
4
4
5
6
7
7
8
8
9
10
10
11
CUSTOMER SERVICE AND TECHNICAL SUPPORT
Hours: 8:00AM to 7:30PM EST (5:00AM - 4:30PM PST)
Call: (800) 831-7133
Visit: www.pentair.com
Fax: (800) 284-4151
1
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
The Pentair Home app is the perfect solution for remotely monitoring and controlling your pool equipment from
anywhere.
This guide provides instructions on creating an account and using Pentair Home to get the most out your Pentair Home
account and your connected pool products.
Home Dashboard
From the Home Dashboard you can remotely monitor and control your pool and equipment. Press a specic
equipment tab to display controls. From any other screen, press the Dashboard Icon [7] to return to the Home
Dashboard.
After a compatible device has been added to your Pentair Home account, the Home Dashboard can be accessed by
tapping the corresponding device tab. For an overview of the Pump Dashboard, refer to Pump Dashboard, page 4.
1− DashboardSettings: Press to access pool info,
notication settings and equipment warranty
information, or log out of Pentair Home.
The Home Dashboard can be customized by
pressing EDIT DASHBOARD.
2− ContactPentair:Press to open the Contact
Pentair screen.
Send a message to Pentair general or device
support, or report bugs within the app.
3− SystemStatus/Alerts:Displays current system
alerts. Press to open a list of alerts.
4− AddaDevice:Press to open the Add a Device
screen.
Choose a device to add to your Pentair
Home Account. For example; ChemCheck,
IntelliConnect, IntelliSync, etc.
5− ControlSystemTab: Displays current system/
device operation mode.
PRESS THIS TAB TO ADD EQUIPMENT TO A
DEVICE.
6− EquipmentTabs:Displays individual equipment
status (pump, heater, salt chlorinator, etc.).
Press a specic tab to open its Equipment
Settings screen.
7− DashboardIcon:Press to return to Home
Dashboard from any screen.
8− DevicesIcon:Press to open the Devices screen.
View all connected devices and equipment.
Press an equipment tab to open its Settings
screen.
9− ScheduleIcon:Press to open the Schedules
calendar.
Displays active schedules for connected
equipment.
10− NoticationsIcon:Press to open the Alerts
screen.
Displays past and present system alerts.
INTRODUCTION
987
6
1
4
3
5
10
2
2
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
INITIAL SETUP
CreatingaPentairHomeAccount
1. From your chosen smart device, download Pentair Home from the
Google Play® store (Android® devices) or Apple® app store (iOS®
devices).
Note: Apple operating systems must be iOS® 11 or later. Android
operating systems must be version6.0orlater.
2. Open the Pentair Home app ( ) from your smart device.
3. A series of informational screens will display.
Scroll through these screens to continue.
4. The Email Entry screen will display.
Enter your email address and press GET
STARTED.
5. The Password Creation screen will
display. See FIGURE 1.
6. Enter your desired password in both
entry elds (1).
7. Review the terms of service by pressing
TERMS OF SERVICE.
Check the Terms of Service Box (2) to
acknowledge you have read the Terms of
Service.
8. Press CREATE MY ACCOUNT (3).
9. The Verify Your Email screen will display
and a verication email will be sent to
the provided email address.
10. Verify your account using the link in the verication email.
Note: If you do not receive a verication email press I DIDN'T GET THE
EMAIL at the Check Your Email screen and follow on-screen instructions.
11. After verication, the Create Prole screen will display. See FIGURE 2.
12. Enter your prole information.
13. Press the STANDARD or METRIC tab to choose which units the app will
display.
14. Press SAVE to save entries.
15. Continue to Pairing Devices to your Account, page 3.
1
2
3
FIGURE 1
FIGURE 2
3
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
PairingDevicestoyourAccount
Several smartphone functions will be used to successfully pair your pump to your Pentair Home account.
Beforesigningintotheappensure:
Your smartphone's Bluetooth® wireless technology is turned on
Your smartphone's location service is on
Pentair Home has Bluetooth permissions
TO PAIR A PUMP TO YOUR ACCOUNT:
1. Sign into your Pentair Home account.
2. The Home Dashboard screen will display (FIGURE 3).
Press ADD A DEVICE [1].
3. The Add a Device screen will display (FIGURE 4).
Select your pump from the list of devices.
4. The Installation screen will display. Press CONTINUE.
5. At the pump, press the CONNECT button on the drive.
6. The pump will enter Bluetooth Pairing Mode and the Connect LED will begin
pulsing Blue.
7. Select your pump to begin Bluetooth pairing.
8. Wait for the Connect LED to turn solid Blue, then press CONTINUE.
9. Once a Bluetooth connection has been established and conrmed, press
CONTINUE.
IfpairingyourpumptoaWiFinetwork: Continue to step 10.
IfnotpairingyourpumptoaWiFinetwork: Press SKIP FOR NOW
to connect only via Bluetooth. Refer to Direct Connect, page 7 for
additional information.
Note: If the pump is not paired to a WiFi network then Pentair
Home control can only be accessed when within Bluetooth range
of the pump.
It is recommended that the pump be paired to a WiFi network
even when not using Pentair Home control. This allows you to
receive the latest updates and features.
10. The Connect Your Device to WiFi screen will display (FIGURE 5).
Select your WiFi network and enter the password. Press CONTINUE.
11. The Device Address screen will display.
Select your address from the Device Address drop down menu and press
CONTINUE.
12. The Nickname screen will display.
Enter the name you would like your pump to go by within Pentair Home. Press SAVE.
13. Installation Completed will display. Press CONTINUE.
14. Your pump is now paired to Pentair Home and ready to use.
1
FIGURE 3
FIGURE 4
FIGURE 5
4
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
PumpDashboard
The Pump Dashboard is your pump's home page. Basic pump info, run status and programming can be viewed from
this screen.
If any pump alerts and problems are present they will also display at the top of this screen.
1− DeviceSettings: Tap to display the Device
Settings screen.
Most of the pump features and settings can be
accessed from the Device Settings screen. Refer
to Device Settings, page 6.
2− Enabled/DisabledToggle: Tap to enable or
disable your pump.
A DISABLED pump will not start until this toggle
is switched to ENABLED or the pump ON/STOP
button is pressed.
3− CurrentStatus:Displays the current pump state.
IDLE: The pump is not currently running a
program.
PROGRAM: Displays the program currently
running.
4− NextProgram:Displays the next program
scheduled to run after completion of the current
program or idle.
If all programs are programmed manual or timer
"No Programs are Scheduled" will display.
5− RunData:Displays estimates of the pump's
current ow, power consumption and overall
system pressure.
6− ProgramTabs: Displays all pump Programs and
their individual settings.
Tap a Program Tab to edit or start a program.
Refer to Program Setup, page 5 for
programming instructions.
Note: Quick Clean will always display as a
program tab and cannot be removed from the
Pump Dashboard. Quick Clean is programmed
similarly to a Timer program.
7− Edit/RunProgramTabs: Displays when a
Program Tab is pressed.
EDIT: Tap to open the Program Setup screen.
Refer to Program Setup, page 5.
 RUNNOW/STOP:Tap to manually start or stop
a pump program.
FIGURE 6
2
3
1
5
6
4
7
OPERATION
5
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
ProgramSetup
The pump allows you to create and customize up to 8 unique programs.
The pump also features a default Quick Clean program that can be
customized, but not renamed or deleted.
1- ScheduleEnabled/DisabledToggle: Tap to enable or disable a
Schedule Program.
If disabled, the schedule program is inactive and will not run until
it is re-enabled.
This toggle will only appear if a program is Schedule Mode.
2− ProgramNickname: Displays the name a specic program will
display on the Pump Dashboard.
Tap the entry eld to edit the program name.
3− ProgramMode:Displays the current Program Mode.
Tap a mode tab to select a mode.
MANUAL: A manual program must be manually started and
stopped from the Pump Dashboard. The program will not
repeat and will run until it is manually stopped.
TIMER: A timer program must be manually started from the
Pump Dashboard but will automatically stop at the end of its
set duration. The program will not repeat and will only run
for its set duration.
SCHEDULE: A schedule program will automatically start
and stop based on its day, start time and end time settings.
The program will repeat at the same time each day on each
day selected.
4− SetSchedule/Timer:
MANUAL MODE: This option will not display for manual
mode programs.
TIMER MODE: Set the run duration for timer mode
programs.
SCHEDULE MODE: Select which days of the week you
want the pump to run and set the duration of these daily
runs.
5− PumpSpeed/Flow:Displays the Speed (percentage of
maximum speed) or the Flow (GPM) set for the program.
Tap the Speed or Flow tab to determine which of these
measurements is displayed.
Use either the +/- buttons to edit the speed/ow setting in minor
increments or the slider to edit in larger increments.
The Activated/Deactivated toggle shows the state of the pump.
If ACTIVATED, the pump is currently active and able to run a
program.
6− RelayToggles: Tap a relay toggle to determine whether a wired
device is active during the program run time.
If a device relay is Activated, the device will run along with pump
the entirety of manual, timer or schedule program.
These toggles only display if the Relay Control Board (P/N
356365z -- sold separately) has been installed.
7− Save: Tap to save edits made to program settings.
TheSAVEbuttonmustbepressedinordertosaveeditsto
settings;otherwisetheywillbelost.
8− RemoveProgram: Tap to permanently delete a program from
the Pump Dashboard. FIGURE 7
1
2
3
4
5
6
7
8
6
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
DeviceSettings
Device Settings can be accessed by pressing the Device Settings gear icon ( ) in the top-right of the Device
Dashboard.
1− ProductOverview: View and edit general information about your
IntelliFlo3 VSF such as device nickname or address.
2− Notications:Control where and how device notications are
delivered.
3− ProductSupport:Opens the IntelliFlo Support page.
4− RemoteMonitoring:Use your address to nd and contact local
pool professionals oering to monitor your pump remotely.
Search results will only contain professionals oering remote
monitoring.
Remote monitoring permissions can be given and revoked from this
screen at any point.
5− ContactaProfessional:Use your address to nd a local pool
professional.
Search results will contain available local pool professionals.
6− WiFi: View and update the WiFi network you are currently paired
to, as well as signal strength.
7− Relays: View and edit your current pump relay device settings and
nicknames.
This functionality is only available if the Relay Control Board (P/N
356365z -- sold separately) has been installed.
Refer to Relays, page 7.
8− AlertsHistory:Displays a list of device alerts.
9− DirectConnect:Setup the Direct Connect feature.
This feature allows you to control your pump without an internet
connection.
Refer to Direct Connect, page 7.
10-PrimingParameters:View and edit your pump's priming settings.
Refer to Priming Parameters, page 8.
11- Limits Parameters: View and edit your pump's speed, ow and
pressure limits.
Refer to Limits Parameters, page 8.
12- Thermal Mode: View and edit the your pump's Thermal Mode
temperature set point and speed/ow settings.
Refer to Thermal Mode, page 9.
13-AutomationAddress:View and edit the pump address associated
with your automation system.
Thepumpaddressenteredonthisscreenmustmatchthe
addressintheautomationsystem.Ifaddressesdonotmatch,
thepumpcannotcommunicatewithanautomationsystem.
14-ExternalControlPrograms: View and edit the four programs
that can be triggered by an external input signal when using the
optional Relay Control Board (P/N 356365z).
15-RampingSpeed:Determine how quickly your pump will ramp up
or down on startup or when changing speeds/ows.
Ramping Speed can be set to FAST, MEDIUM or SLOW.
16-DeviceSecurity:
Set a 4-digit PIN controlling access to pump controls.
10-DeviceResets:Restore system defaults for all programs and device settings.
15-RemoveDevice:Remove the pump and pump relay devices from your Pentair Home account.
FIGURE 8
7
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
Relays
PumpDashboard˃DeviceSettings˃Relays
The following functionality is only available if the Relay Control Board (P/N 356365z -- sold separately) has been
installed.
The relay board includes two high-voltage terminals capable of
controlling pool lights, salt chlorine generators or other ltration
system components. One terminal is intended for 5A max low-
current connections and the other for 16A max high-current
connections.
1- DeviceType: Select the device connected to a particular relay.
 RELAY1Options: Lights, Salt Cell or Other
 RELAY2Options:Lights, Salt Cell, Booster Pump or
Other
Note: If a relay is designated "Booster Pump", the
pump will rst ensure the Booster Pump has water by
delaying power to the relay until the pump has run for
two minutes.
If the pump is already running a program then there will
be no delay.
2− DeviceNickname: Enter the name you want your device to
display on Program Setup screens.
3− Speed/FlowDependent: Check this box to ensure the relay is
only activated when the pump is running.
4− Add/Remove: Tap to add or remove a relay.
DirectConnect
PumpDashboard˃DeviceSettings˃AdvancedSettings>DirectConnect
Direct Connect mode allows you to program and operate your pump without a WiFi connection, via a Bluetooth®
wireless technology connection.
TO PLACE THE PUMP INTO DIRECT CONNECT MODE:
1. Ensure your smartphone is within Bluetooth range of the pump, Bluetooth is enabled on your smartphone and
Pentair Home has Bluetooth permissions.
2. At the pump, press the CONNECT button to enter pairing mode. The pump's CONNECT LED will blink blue.
3. Open Device Settings and select Direct Connect.
4. Press CONTINUE at the Bluetooth Pairing screen.
5. Once a Bluetooth connection is established, the pump's CONNECT LED will turn solid blue.
WhenconnectedtothepumpviaBluetooth,thefollowingoptionswillappearintheDirectConnectmenu:
SET-UPWIFI:Tap to establish a WiFi internet connection between your phone and the pump. WiFi will now be
your primary connection.
DISCONNECT: Tap to disconnect your Bluetooth wireless connection.
Note: When the pump is programmed to operate in Direct Connect mode and has been powered o, the Connect
LED will pulse yellow. This indicates that the pump needs to be re-paired with your smartphone.
Press the CONNECT button to reconnect with your previously paired smartphone.
Note: When connected via WiFi, a green dot will display beside the pump nickname on the Pump Dashboard.
When connected via Bluetooth and operating in Direct Connect mode, the Bluetooth symbol will display beside the
pump nickname on the Pump Dashboard.
4
3
2
1
FIGURE 9
8
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
PrimingParameters
PumpDashboard˃DeviceSettings˃AdvancedSettings>PrimingParameters
All priming settings can be edited and set from this screen. Tap a specic setting on the right-side of the screen to edit.
1- Enabled/Disabled: ENABLED allows the pump to detect whether
or not the system is properly primed for pump startup.
Ifprimeisnotdetectedthepumpwillenteraprimingcycle,
basedonthesettingsbelow.
2− PrimingSpeed: Set the speed the pump will run during a priming
cycle.
3− MaxPrimingDuration: Set the maximum amount of time the
pump will attempt to prime.
If the pump does not achieve prime during this time a priming error
will display and the pump will stop.
4− PrimingRange: Set the sensitivity of pump prime detection.
Lower settings require higher ow to detect a successful prime.
5− PrimingDelay: Set the amount of time the pump remains at
priming speed before transitioning to the run program.
6− LossofPrime: ENABLED allows the pump to detect low-ow or
no-ow situations while running.
If a loss of prime is detected the pump will pause and attempt to
prime, based on the settings above. If priming is successful the
pump will continue programmed operation.
Limits Parameters
PumpDashboard˃DeviceSettings˃AdvancedSettings>Limits Parameters
Set and edit pump speed, ow and pressure limits. These settings will ensure your pump does not operate
outside of the programmed parameters.
1- Minimum/MaximumSpeed: Set the absolute minimum and maximum
speeds the pump will be allowed to run. Pump run speed will
never run under or over these two settings.
2− Minimum/MaximumFlow: Set the absolute minimum and
maximum ow rate the pump will be allowed. Pump GPM will
never fall under or exceed these two settings.
Note: These minimum and maximum ow rates only apply to
Flow Programs. To apply these settings to Speed Programs as
well, the next setting (Flow Limit - Speed Programs) must be
enabled.
3− FlowLimit(SpeedPrograms): Enable or disable minimum and
maximum ow rate limits for Speed Programs.
4− MaxPressure: Set the absolute maximum system pressure the
pump will be allowed to produce. Pump system pressure will never
exceed this setting.
Note: The maximum pressure setting only applies to Flow
Programs. To apply these settings to Speed Programs as well,
the next setting (Pressure Limit - Speed Programs) must be
enabled.
5− PressureLimit(SpeedPrograms): Enable or disable maximum
system pressure limit for Speed Programs.
FIGURE 10
1
2
6
5
4
3
FIGURE 11
1
5
3
4
2
9
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
Thermal Mode
PumpDashboard˃DeviceSettings˃AdvancedSettings>
Thermal Mode
Thermal Mode is intended to help protect the pump during freezing
or near-freezing conditions.
Note: Do not depend on this feature for freeze protection of the
entire ltration system and pool.
Certain situations could cause the pump to sense a dierent
temperature than actual air temperature. Your automation system air
temperature sensor should be used to sense actual temperature. For
example, if the pump is located indoors, the temperature of the room
does not indicate the outdoor temperature.
Note: The pump does NOT sense water temperature.
1- Enable/Disable: Enable or disable Thermal Mode protection.
2− TemperatureSetPoint: Set the temperature at which the
Thermal Mode program will initiate.
3− Speed/FlowDisplay: Determines whether the Speed/Flow
setting below is displayed as a percentage of max speed or in
GPM.
4− Speed/FlowSetting: Set the Speed% or GPM the pump will
run when Thermal Mode is triggered.
5− Save: Saves edits to Thermal Mode settings.
FIGURE 12
1
2
4
3
5
10
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
ConnectionIssue-
PumpisOineAlert
Pump is not receiving power Ensure the pump is receiving power.
If the pump is receiving power, the ON/STOP button will
illuminate.
Home internet service is out or
inaccessible
Conrm that the home router is active and connected to
the internet.
Intermittent WiFi or network
connection
1. Restart the home router. This can clear up many
typical home networking issues.
2. Cycle power the pump.
Disconnect power to the pump at the main breaker,
Wait for 1 minute and reconnect power.
3. Check the signal strength in WiFi Settings of the
Pentair Home App.
If the signal strength is insucient, refer to the Poor
WiFi Signal section of this troubleshooting chart.
Bluetooth® connectivity issues 1. Stand closer to the pump when operating via
Bluetooth.
2. Restart the Pentair Home app.
3. Adjust the pump antenna.
4. Ensure smartphone permissions are given to the
pump.
Poor WiFi signal to router 1. The WiFi antenna can be relocated from the top cover
of the drive to a location with better WiFi signal.
The antenna bulkhead on the cover has a SMA
Female connector, and the antenna has a SMA Male
connector.
A SMA extension cable can be used to move the
antenna to a more favorable location such as around
the corner of a wall or outside of an enclosure.
2. Consider operating the pump in Direct Connect
mode. Refer to the Direct Connect, page 7 for
instructions.
TroubleshootingChart
TROUBLESHOOTING
11
INTELLIFLO3™ VSF and INTELLIPRO3™ VSF Variable Speed and Flow Pump User's Guide
AlarmsandWarnings
When an alarm is triggered the drive's ON/STOP LED will blink RED and a fault code will display. The pump will stop
until the alarm is resolved.
When a Warning is triggered the drive's ON/STOP LED will blink GREEN/YELLOW and a fault coded will display.
Dependingonyourparticularsetup,faultcodeswilldisplayononeormoreoftheuserinterfaces:
Pentair Home App
Automation System Interface
Optional Touchscreen Controller (Almond - P/N 356159z, Black - P/N 356348z)
ALARM/
WARNING DESCRIPTION DEFINITION
Weak Wi-Fi
Connection
Weak Wi connection
detected.
Pump antenna may be obstructed or too far away from your router. The antenna wire can
be extended.
Refer to the IntelliFlo3 VSF Installation and Maintenance Guide (P/N 356231) for
instructions.
Oine The pump is oine. The Pentair cloud cannot connect to your pump.
This could be caused by a power outage at the pump or router, or a loss of WiFi signal to
the pump.
Priming Failure The pump has reported a
Priming Failure Alarm.
Priming failure can be caused by lack of water in the volute strainer basket.
Overheat The pump has reported an
Overheat Condition.
The pump motor has detected an abnormally high internal temperature. This can be
caused by a blockage of the cooling fan inlet or outlet, or by excessively high ambient air
temperature.
The pump will attempt to protect itself by reducing the motor speed to give the motor and
drive a chance to cool down.
Over Current The pump has reported an
Over Current Condition.
Load has increased on the motor; due to debris, part interference, temperature issues, age
of parts, or supplied voltage.
Inspect the rotating parts of the pump for blockages or debris buildup.
Refer to the pump IntelliFlo3 VSF Installation and Maintenance Guide (P/N 356231) for
disassembly and reassembly instructions.
Over Voltage The pump has reported an
Over Voltage Alarm.
Supplied voltage is outside of the proper range. When voltage returns to the normal the
alert will clear and the pump will resume operation.
Under Voltage The pump has reported an
Under Voltage Alarm.
Supplied voltage is outside of the proper range. When voltage returns to the normal the
alert will clear and the pump will resume operation.
Speed Limit The pump has reported a
Speed Limit Warning.
The pump is operating at the programmed maximum speed in order to achieve the desired
speed/ow.
Refer to Limits Parameters on page 8 for instructions on adjusting the Speed Limit.
If this alert displays and the Speed Limit is already set to 100%, then the pump may not be
capable of achieving the desired ow rate.
Pressure Limit The pump has reported a
Pressure Limit Warning.
The pump is operating at the programmed maximum system pressure.
The pump monitors Total Dynamic Head, and not outlet pressure, so it may dier from the
reading on the lter gauge.
Refer to Limits Parameters on page 8 for instructions on adjusting the pump Pressure
Limit.
Flow Limit The pump has reported a
Flow Limit Warning.
The pump is operating at the programmed maximum ow rate.
Refer to Limits Parameters on page 8 for instructions on adjusting the pump Flow Limit.
Internal Fault The pump has an internal
error.
This alert can be caused by a few dierent types of internal hardware or software errors in
the drive.
Disconnect power to the pump and reconnect after one minute. If the alert remains,
contact a qualied pool professional.
Drive is Derating
(Warning)
The pump is slowing down
to prevent the drive from
overheating.
This alert usually accompanies an Overheat or Over Current alert.
It is intended to note that the pump will continue to operate at a reduced speed as long as
possible.
After the drive has cooled enough it will automatically resume normal operation.
Derating Alarm -
Exceeded & Cut O
The pump has stopped
to prevent the drive from
overheating.
The motor and drive are not able to reduce speed enough to protect themselves.
The motor will stop and Pentair Home will display this alarm.
When the drive has cooled enough, it will automatically resume operation and attempt to
run the requested program.
Thermal Mode The pump operating in
Thermal Mode.
The pump is operating in Thermal mode. Thermal Mode is controlled by the drive's internal
temperature, not water temperature.
Thisisintendedtokeepmotorcomponentsfromfreezing,butshouldnotbesolely
reliedonforfullltrationsystemfreezeprotection.
1620 HAWKINS AVE., SANFORD, NC 27330 • (919) 566-8000
10951 WEST LOS ANGELES AVE., MOORPARK, CA 93021 • (805) 553-5000
WWW.PENTAIR.COM
All indicated Pentair trademarks and logos are property of Pentair. Third party registered and unregistered trademarks and logos are the property of
their respective owners. Apple® and App Store® are registered trademarks of Apple Inc. in the United States and/or other countries. iOS® is a registered
trademark of Cisco Technology, Inc. in the United States and/or other countries. Google Play® and Android® are registered trademarks of Google LLC in
the United States and/or other countries. The Bluetooth® word mark and logo are registered trademarks of Bluetooth SIG, Inc. in the United States and/
or other countries. Other trademarks and trade names are those of their respective owners. Because we are continuously improving our products and
services, Pentair reserves the right to change specifications without prior notice.
© 2022 Pentair. All rights reserved. This document is subject to change without notice.
*356088*
P/N 356088 REV. B 1/26/22
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Pentair 011075 User guide

Category
Above ground pool accessories
Type
User guide

Pentair 011075, an IntelliFlo3 VSF variable speed and flow pump, offers advanced pool management capabilities. Its intelligent programming optimizes energy usage and provides quiet operation. With built-in automation features, you can customize pump speed and flow to suit your pool's specific needs, saving energy and money.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI