t's
easy
to get
started.
Simp
y
connect
your
new Rockbot
Media
Payer
to:
D
-
INTERNET AUDIO
DISPLAY
Fo
ow
this guide and
you' be rocking
out
in
no time.
IF
at
anytime
during
the
installation you
need
extra assistance,
contact
our
support
team
at
support@rockbot.com,
415-813-6020
ext
1
or
visit
our
online
help
center
at
support.rockbot.com.
What's
in
the
box?
Two-Piece
Power
Adapter
USB-C
to
3.5mm Adapter
Ethernet Cable
HDMI
Cable
2
• •
Rockbot
Media
Pl
ayer
RCA
Cable
MicroSD
Card
(Already
inserted)
1 i
t·
1
II
I
WiFi
Antenna
(WiFi
pl
ayers
only)
nsta
your
payer
INSTALLING A WIFI
PLAYER
?
Visit setup.rockbot.com for instructions
to
install your
wifi player and connect
it
to
your network.
KNOW YOUR
PORTS
0 CHECK MICROSD
Before installing the
Rockbot
Media
Player,
ensure the M icroSD card
is
completely inserted.
Be
careful when connecting adapters and ensure
that
they are inserted
into
the
right
port
to
prevent damaging
of
player and cables.
0 M icr
oSD
0
USB
0 Ethernet
0
HDMI
C,
WiFi
Antenna
WiFi
Players
Only
0 Power
Note: Some models
will
have ports located
in
different locations then those illustrated above.
3
CJ
®00
G PLUG
IN
INTERNET
Connect
an
Ethernet
Cab
le from
the
Rockbot
Media
Player to
an
open
port
on
your
router/modem.
e FOR
WIFI
PLAYERS
To install a WiFi player, visit
setu
p.rockbo t.co m.
0
OPTIONAL
PLUG IN DISPLAY
If
you
are
not
using a display, skip this
step.
Connect
the
HDMI
cable
from
the
Rockbot
Media
Player
to
your
video
display.
4
00(:)000
0 PLUG IN
AUDIO
Use
the
USB-C
to
3.5mm
adapter
to
plug
the
RCA
cables
from
your
amplifier/receiver into
the
USB
port
on
the
Rockbot
Media
Player.
Note:
Some
models have a
3.5mm
port
and
do
not
require the adapter.
0 PLUG IN POWER
Insert
the
power
cord
into
the
Rockbot
Media
Player
and
the
other
end
to
a
power
source. Within 10 min, music
and
display should
start
streaming.
Important: plug
in
power
last.
Something
wrong?
Here
are
some
ti
ps.
If
no
audio plays
after
10
min
try
the
following:
•
Power
cycle
the
Rockbot
Media
Player
by
unplugging
the
power
adapter
, wait until all lights
are
off
and
then
plug
the
adapter
back
in.
All
connections
on
the
device
should
be
seated
.
•
Connect
a
standard
set
of
headphones/earbuds
into
the
audio
adapter
in
your
Rockbot
Media
Player.
•
If
you
hear
audio
,
reconnect
the
audio
cab
le
into
the
Rockbot
Media
Player. Verify
that
the
amplifier/
receiver
is
connected
to
the
proper
source
and
the
vo
lume
on
the
amplifier is
turned
up
.
•
If
yo
u
don
't
hear
audio
,
ensure
there
is
a red
power
light
on
the
Rockbot
Media
Player.
Che
ck
to
make
sure
the
microSD
card
is
firmly
seated
in
the
device
.
Confirm
that
the
Rockbot
Player has
access
to
the
necessary
Rockbot servers, email
to
request
network
requirements
.
5
If
you hear error messages:
•
If
you
hear
error
messages
through
your
speakers
or
if
your
Rockbot
Media
Player is
not
playing music,
there
may
be
a firewall
or
network
issue,
contact
support
team
at
support
@
rockbot
.c
om
for network
requirements.
If
you're
not
getting
any display
try
the
following:
•
Make
sure
HDMI
cable
is
firmly
attached
to
player
and
display.
• Make
sure
video
display
is
set
to
the
proper
HDMI
input
source
.
• Power cycle
the
Rockbot
Media
Player
and
then
the
display
to
re-establish
input
detection
.
WiFi
player installation
• To install a WiFi player, visit
setup.rockbot.com
Meed
further
assistance?
Contact
our
support team at
support
@rockbot.com,
415-813
-6020
ext
1
or
visit
our
on
line help center at
suppo
rt
. rockbot.com.
v201871
Avoid Damaging Your Rockbot
Media
Player's Power Cable
The
power cable should
be
easy
to
insert.
It
is
normal to
see a
gap
between
the
rubber
on
the
power
cord
and
the
plastic
on
the
unit.
Do
not
force
the
cable
into
the
socket
or
damage
may
occur.
• Insert
the
cord straight into
the
Rockbot Player.
•
Do
not
insert
or
remove
at
an
angle
or
jerk
the
cable.
•
If
you use cable ties, place
them
at
least four inches
from
the
end
of
the
cable
to
avoid
damage.
Keep Organized
Use
the
stickers provided
below
to
help keep
organized, and
to
avoid
others from accidentally
unplugging any cables
from your Rockbot player.
Use
the
support card
sticker
to
stick anywhere
you want,
or
simply
cut
it
out
and save it for future
reference.
~
ROCKBOT
SUPPORT
HOURS
6AM
-
6PM
PST
MON
-SAT
(415)
813-6020
xl
SUPPORT@ROCKBOT
.
COM
EMERGENCY AFTER-HOURS SUPPORT AVAILABLE
_
____________________________
-io_
ROCKBOT ROCKBOT
ROCKBOT ROCKBOT
ROCKBOT
ROCKBOT
Cable Stickers Power Cord Sticker
ROCKBOT
support.rockbot.com
DO
NOT
UNPLUG
Apply
the
Cable
Stickers
to
the
ends
of
your
player's cables. This
will
allow you
to
quickly
identify which cables are plugged into
the
player.
Apply Power
Cord
Sticker
to
the
top
of
the
power cord. This
will
help
to
prevent others
from unplugging your player.
~
R
KB
□
T
Getting started with music is easy.
visit: rockbot.com / activate
You
'JI
need
your
serial
nurnber
handy,
found
on
the back
of
your Rockbot
Player.
/
