Page is loading ...
BPI-0611 1
PICMG Backplane with 6-Slots
(PICMG x 2, PCI x 3, ISA x 1)
BPI-0611 User's Manual
CONTEC CO., LTD.
Description
BPI-0611 is the Backplane board which have the 2 PICMG (1 PICMG/PCI) + 3 PCI + 1 ISA slots. The
Backplane board have two SBC(CPU board) PICMG slots(PICMG1and PICMG2) and three PCI Bus
slots(PCI2 - PCI4) and one ISA Bus slot(ISA1). PICMG2 and PCI1 is shared bus slot.
Package Contents
- The BPI-0611 Backplane Board
- This User's Manual
- ATX Control 6pin Cable
Features
- 1 PICMG + 1 PICMG/PCI + 3 PCI +1 ISA slots
- Support for ATX and AT compliant power supply.
- The optional chassis suitable for mounting.
Specifications
Item Specification
Correspondence bus PCI/ISA(PICMG) Bus, ISA Bus , PCI Bus
Number of slots *1 SBC(CPU board) PICMG slot(PICMG1) x 1 *1
SBC(CPU board) PICMG/PCI shared bus slot (PICMG2 / PCI1) x 1 *1
PCI bus slot(PCI2 - 4) x 3
ISA bus slot(ISA1) x 1
Supply power +5VDC, -5VDC, +12VDC, -12VDC, +3.3VDC(only for ATX power supply)
Operating conditions 0 - 60°C, 10 - 90% RH (No condensation)
Storage conditions -20 - 70°C
Floating dust particles Not to be excessive
Corrosive gases None
Major dimensions (mm) 145.3(W) x 264.2(D)
Weight 310 g
Installable chassis FA-UNIT-F6RFV, FA-UNIT-F6DR
*
1 The SBC(CPU board) must install it to the PICMG slot(PICMG1 or PICMG2).
*2 PICMG2/P_PCI1 slot is a shared slot. Only one of the boards, PICMG or PCI, can be mounted.
BPI-0611 User's Manual
2 BPI-0611
Board Dimension
PW3
PW2
PW1
CN2
FAN2
FAN1
JP1
CN1
145.3
139.7
127.5
121.7
112.1
109.0
96.2
55.7
35.1
15.2
2.5
63.8
264.2
254.3
201.9
188.9
174.6
165.9
165.1
13.7
10.2
25.4
41.3
[mm]
BPI-0611 User's Manual
BPI-0611 3
Jumper Setting and Connectors
AT Power Supply Connector: PW1
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
Function
Power Good
+5V
+12V
-
12V
GND
GND
GND
GND
-
5V
+5V
+5V
+5V
Suitable Housing : GTC6P-1(correspond)
Suitable Contact : PCK18-2TR9(correspond)
Maker : BURNDY
Option Cable
(One side is solder disposal.)
Model : PCA-6P2 CONTEC
Cable length 36cm(AWG#18), two
PW1
1
ATX Power Supply Connector: PW2
When used with an ATX-compliant power supply that supports remote power on/off, the CPU card can
turn off the system power through software control.
To enable soft-off control in software, advanced power management must be enabled in the Setup
program and in the operation system. When the system BIOS receives the correct APM command from
the operating system, the BIOS turns off power to the computer.
With soft-off enabled, if power to the computer is interrupted by a power outage or a disconnected power
cord, when power resumes, the computer returns to the power state it was in before power was interrupted
(on or off).
Pin No.
1
2
3
4
5
6
7
8
9
10
Function
+3.3V
-12V
GND
PON
GND
GND
GND
-5V
+5V
+5V
Pin No.
11
12
13
14
15
16
17
18
19
20
Function
+3.3V
+3.3V
GND
+5V
GND
+5V
GND
Power Good
+5VSBY
+12V
PW2
Suitable Housing : 39-01-2200 (correpond)
Suitable Contact : 5556 (correspond)
Maker : Molex
11 1
20 10
BPI-0611 User's Manual
4 BPI-0611
Power Supply Terminal: PW3
When you input the power supply from the PW1 or PW2 connectors, you can output +5V,
-5V,
+12V and
–12V power from the PW3 terminal. The maximum output current of each power supply is showed
bellow.
Specification of Power Supply Terminal
Voltage +5VDC +12VDC -5VDC -12VDC
Max. Current 2A 2A 2A 2A
However, the maximum supply current is depend on the power supply connected to PW1 or PW2.
Suitable Ring Tongue : WS0.5-3 (correspond)
Suitable Spade Tongue : WS0.5-3A (correspond)
Applicable Wire AWG#(mm
2
) : 26 - 22(0.2 - 0.5)
Maker : JST
Screw torque : 0.4N-m(Max.)
+5V
-5V
+12V
-12V
GND
3.63
6.35±0.05
[mm]
PW3
System FAN Connector: FAN1 / FAN2
FAN1 and FAN2 are 3-pins header for the system cooling fan power connector. The fan must be a 12V
fan. Pin 2 is for +12V power supply.
1
2
3
FAN1/FAN2
Pin No.
1
2
3
Function
N.C.
+12V
GND
Suitable Housing : 22-01-1034 (correspond)
Suitable COntact : 08-70-0057 (correspond)
Maker : Molex
ATX Power Control Connector: CN1(PWRCTL)
Pin No.
1
2
3
4
5
6
Function
PME#
GND
PBTN-IN
GND
PSOUT
+5V SBY
CN1
1
2
3
4
5
6
Suitable Housing: XHP-6 (correspond)
Suitable Contact : SXH-001T-P0.6 (correspond)
Maker : JST
ATX Power Button connector: CN2(PWRBTN)
Pin No.
1
2
Function
PBTN
GND
CN2
Suitable Housing : XHP-2 (correspond)
Suitable Contact : SXH-001T-P0.6 (conrrespond)
Maker : JST
21
BPI-0611 User's Manual
BPI-0611 5
ATX Power ON: JP1
Pin No.
3
2
1
Function
GND
PBIN
PSOUT
2-3 Short : Disable ATX power control and set the
ATX Power Supply ON always by push
switch
(use as AT Power Supply).(Default))
1- 2 Short : Enable ATX Power Control by push
switch
3
2
1
JP1
Connector Block Drawing
1
2
6
5
4
3
2
1
JP1
3 2 1
9+5VSBY
14 PON
ATX Power Connector
ATX Power ON/OFF Switch
GND
PBTN
+5VSBY : +5V Stanby Voltage supplied to CPU board.
PS_OUT : ATX Power Supply ON (Low Lebel) Signal from CPU board.
GND
PBTN_IN: Output Switch Signal (connected to CN2) to CPU board.
GND
PME# :
PME# signal is input to the CPU board. They are valid
only for the signals compatible with the CPU board
(See the CPU board manual).
[Connect to CPU board with 6pin Cable (included).]
CN1
CN2
PW2
BPI-0611 User's Manual
6 BPI-0611
Copyright
Copyright 2005 CONTEC CO., LTD. ALL RIGHTS RESERVED
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document. The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may appear
in this document nor for results obtained by the user as a result of using this product.
Limited One-Year Warranty
CONTEC IPC Series are warranted by CONTEC CO., LTD to be free from defects in material and
workmanship for up to one year from the date of purchase by the original purchaser.
Repair will be free of charge only when this device is returned freight prepaid with a copy of the original
invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from
which it was purchased.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and
original boards. The warranty is not applicable if the device has been tampered with or damaged
through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in
which case repairs will be considered beyond the warranty policy.
BPI-0611 User's Manual
BPI-0611 7
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please
obtain a Return Merchandise Authorization Number (RMA) from the CONTEC group office where you
purchased before returning any product.
* No product will be accepted by CONTEC group without the RMA number.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor
be liable for any incidental or consequential damages due to such defect or consequences that arise from
inexperienced usage, misuse, or malfunction of this device.
BPI-0611 User's Manual
BPI-0611
User’s Manual
CONTEC CO.,LTD. June 2005 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD. [06272005]
[04082005] Management No. A-46-994
[06272005_rev2] Parts No. LYEQ661
/