Eldes EPGM8 User manual

Eldes
Brand
Eldes
Model
EPGM8
Type
User manual

Eldes EPGM8 is a PGM output expansion module intended for using with ELDES alarm systems. This module allows to connect up to additional 8 electrical appliances. Eldes EPGM8 is compatible with ESIM264 / ESIM364 and has 8 PGM outputs with 100mA max current, open collector output. Maximum Commuting PGM Output Values are: Voltage – 30V; current 500mA. The device has compact dimensions of 40 x 55 x 15 mm and wide range of operating temperatures: -20...+55ºC. Eldes EPGM8 must be powered by 10-24V 100mA max.

Eldes EPGM8 is a PGM output expansion module intended for using with ELDES alarm systems. This module allows to connect up to additional 8 electrical appliances. Eldes EPGM8 is compatible with ESIM264 / ESIM364 and has 8 PGM outputs with 100mA max current, open collector output. Maximum Commuting PGM Output Values are: Voltage – 30V; current 500mA. The device has compact dimensions of 40 x 55 x 15 mm and wide range of operating temperatures: -20...+55ºC. Eldes EPGM8 must be powered by 10-24V 100mA max.

PGM OUTPUT EXPANSION MODULE
EPGM8
2
EPGM1 is a PGM output expansion module intended for using with ELDES alarm systems. This module allows to connect up to
additional 8 electrical appliances.
Main EPGM8 features:
• PGM output expansion adding 8 additional PGM outputs
• compatible with ESIM264 / ESIM364
1. Package Content
1. EPGM8.............................................. .......................qty. 1
2. EPGM8 User Manual... .......................................qty. 1
2. Technical Specications
2.1 Electrical & Mechanical Characteristics
Power Supply 10-24V 100mA max
Number of PGM Outputs 8
PGM Output D1-D8 Circuit
Maximum Commuting PGM Output Values Voltage – 30V; current 500mA
Dimensions 40 x 55 x 15 mm
Range of Operating Temperatures -20...+55ºC
2.2 Connector Functionality
D1 - D8 PGM outputs
12V Positive power supply contact
GND Negative power supply contact
1 R
OUT
D1 D2 D3 D4 D5 D6 D7 D8
12V GND
Fig. No. 1
Open collector output.
Output is pulled to COM when
turned on.
USER MANUAL EPGM8 V1.0 3
3. Installation
1. Disconnect ELDES alarm system main power supply and backup battery.
2. Insert EPGM8 pins to appropriate ELDES alarm system slots (see Fig. No. 2)
3. Connect EPGM8 12V positive power supply contact with ELDES alarm system AUX+ contact and EPGM8 GND contact with
ELDES alarm system AUX- contact. (see Fig. No. 3).
4. Connect the electrical appliances to D1 – D8 PGM outputs. (see Fig. No. 3)
5. Power up ELDES alarm system.
6. Enable EPGM8 mode using EKB2, EKB3 keyboards or ELDES Conguration Tool software. For more details, please, refer to
software’s HELP section or see ELDES alarm system installation manual.
7. EPGM8 is ready for use with ELDES alarm system.
C4
C3
SIM
CARD
SMA
ANTENNA
FUSE
3A
PWR
Z4
Z3
Z2
Z1
C1
C2
NETWORK
Z5
Z6
STA TUS
AKU+
AKU-
COM
BELL-
BELL+
G
Y
C2
AUX-
AUX+
AC/DC
AC/DC
Z1
COM
Z2
Z3
COM
Z4
DATA
+5V
MIC -
MIC+
BUZ-
C1
BUZ+
COM
COM
Z6
Z5
USB
DEF
PRG
D1 D2 D3 D4 D5 D6 D7 D8
12V GND
EPGM8
ESIM264
D1 D2 D3 D4 D5 D6 D7 D8
TO AUX+
12V
ESIM264
EPGM8
GND
TO AUX+
TO AUX+
TO AUX+
TO AUX+
TO AUX+
TO AUX+
TO AUX+
El. Appliance 1
El. Appliance 2
El. Appliance 3
El. Appliance 4
El. Appliance 5
El. Appliance 6
El. Appliance 7
El. Appliance 8
AUX- AUX+
Fig. No. 2
Fig. No. 3
4
4. Additional Information
Limited Liability
The buyer must agree that the system will reduce the risk of re, theft, burglary or other dangers but does not guarantee against
such events.“ELDES UAB” will not take any responsibility regarding personal or property or revenue loss while using the system.
“ELDES UAB” liability according to local laws does not exceed value of the purchased system. “ELDES UAB” is not aliated with any
of the Internet providers therefore is not responsible for the quality of Internet service.
Manufacturer Warranty
This device carries a 24-month warranty by the manufacturer “ELDES UAB”. Warranty period starts from the day the system has
been purchased by the end user. The warranty is valid only if the system has been used as intended, following all guidelines listed
in the manual and within specied operating conditions. Receipt must be kept as a proof of purchase date. The warranty is voided
if the system has been exposed to mechanical impact, chemicals, high humidity, uids, corrosive and hazardous environment or
other force majeure factors.
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and people around:
• DO NOT use the system where it can be interfere with other devices and cause any potential danger.
• DO NOT use the system with medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.
• DO NOT attempt to personally repair the system.
EPGM8 must be powered by 10-24V 100mA max. DC power supply which must be approved by LST EN 60950-1 standard
and be easily accessible nearby the device. When connecting the power supply to EPGM8, switching the pole terminals places
is forbidden.
Any additional devices linked to EPGM8 (electrical appliances, relays etc.) must be approved by LST EN 60950-1 standard.
Main power and backup battery of ELDES alarm system must be disconnected before any installation or tuning work starts. The
system installation or maintenance must not be done during stormy conditions.
EPGM8 is fully turned o by disconnecting 2-pole switch device of the external power supply or any other linked
device that EPGM8 is powered from.
Copyright © “ELDES UAB”, 2011. All rights reserved
It is not allowed to copy and distribute information in this document or pass to a third party without advanced written authorization
by “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby,
„ELDES UAB“ declares that this PGM output expansion module EPGM8 is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that
the product must not be disposed of together with household waste. To prevent possible harm to human health and/or the
environment, the product must be disposed on in an approved and environmentally safe recycling process. For further infor-
mation on how to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste
disposal in your area.
USER MANUAL EPGM8 V1.0 5
Made in Lithuania.
www.eldes.lt
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Eldes EPGM8 User manual

Eldes
Brand
Eldes
Model
EPGM8
Type
User manual

Eldes EPGM8 is a PGM output expansion module intended for using with ELDES alarm systems. This module allows to connect up to additional 8 electrical appliances. Eldes EPGM8 is compatible with ESIM264 / ESIM364 and has 8 PGM outputs with 100mA max current, open collector output. Maximum Commuting PGM Output Values are: Voltage – 30V; current 500mA. The device has compact dimensions of 40 x 55 x 15 mm and wide range of operating temperatures: -20...+55ºC. Eldes EPGM8 must be powered by 10-24V 100mA max.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents