Flytech POS365 User manual

USER MANUAL

Point-of-Sale

Hardware

System

VERSION V1.4 January 2011

ii

Manual Version 1.4

Part Number: 3LMPP3600314

The information contained in this document is subject to change without notice.

We make no warranty of any kind with regard to this material, including, but not

limited to, the implied warranties of merchantability and fitness for a particular

purpose. We shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of

this material.

This document contains proprietary information that is protected by copyright. All

rights are reserved. No part of this document may be photocopied, reproduced

or translated to another language without the prior written consent of the

manufacturer.

TRADEMARK

Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.

Microsoft® and Windows® are registered trademarks of Microsoft Corporation.

Other trademarks mentioned herein are the property of their respective owners.

Safety

IMPORTANT SAFETY INSTRUCTIONS

To disconnect the machine from the electrical power supply, turn off the power 1.

switch and remove the power cord plug from the wall socket. The wall socket must

be easily accessible and in close proximity to the machine.

Read these instructions carefully. Save these instructions for future reference.2.

Follow all warnings and instructions marked on the product.3.

Do not use this product near water.4.

Do not place this product on an unstable cart, stand, or table. The product may fall, 5.

causing serious damage to the product.

Slots and openings in the cabinet and the back or bottom are provided for 6.

ventilation to ensure reliable operation of the product and to protect it from

overheating. These openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed, sofa, rug, or other

similar surface. This product should never be placed near or over a radiator or heat

register or in a built-in installation unless proper ventilation is provided.

This product should be operated from the type of power indicated on the marking 7.

label. If you are not sure of the type of power available, consult your dealer or local

power company.

Do not allow anything to rest on the power cord. Do not locate this product where 8.

persons will walk on the cord.

Never push objects of any kind into this product through cabinet slots as they 9.

may touch dangerous voltage points or short out parts that could result in a re or

electric shock. Never spill liquid of any kind on the product.

iii

CE MARK

This device complies with the requirements of the EEC directive 2004/108/EC

with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage

Directive”.

FCC

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that

may cause undesired operation.

CAUTION ON LITHIUM BATTERIES

There is a danger of explosion if the battery is replaced incorrectly. Replace only

with the same or equivalent type recommended by the manufacturer. Discard

used batteries according to the manufacturer’s instructions.

Battery Caution

Risk of explosion if battery is replaced by an incorrectly type.

Dispose of used battery according to the local disposal instructions.

Safety Caution

Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S)

related legislation, peripherals shall be 4.7.3.2 “Materials for fire enclosure”

compliant

4.7.3.2 Materials for  re enclosures

For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material

of a FIRE ENCLOSURE, in the thinnest signi cant wall thickness used, shall be

of V-1 CLASS MATERIAL or shall pass the test of Clause A.2.

For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all

STATIONARY EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest

signi cant wall thickness used, shall be of 5VB CLASS MATERIAL or shall pass

the test of Clause A.1

iv

LEGISLATION AND WEEE SYMBOL

2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment,

collection, recycling and disposal of electric and electronic devices and their

components.

The crossed dust bin symbol on the device means that it should not be disposed

of with other household wastes at the end of its working life. Instead, the device

should be taken to the waste collection centers for activation of the treatment,

collection, recycling and disposal procedure.

To prevent possible harm to the environment or human health from uncontrolled

waste disposal, please separate this from other types of wastes and recycle it

responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this

product, or their local government office, for details of where and how they can

take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of

the purchase contract.

This product should not be mixed with other commercial wastes for disposal.

v

Revision History

Changes to the original user manual are listed below:

Revision Description Date

V1.0 nitial release• 2007 March

V1.1 System Disassembly updated• 2007 May

V1.2

Cover page updated•

Connector Pin Denition updated•

2007 September

V1.2a Cash Drawer Power Setting Correction• 2007 September

V1.2b

Cash Drawer Power Setting Correction•

Updated specification with Second Display op-•

tions

Updated Optional Items with Second Display op-•

tions

Updated LCD ID jumper settings•

2008 June

V1.3

Motherboard B78 v1.0 updated to v2.2•

2nd display installation added•

VFD installation added•

SATA HDD photo added•

2-in-1 MSR + iButton module added•

2–in-1MSR + Finger Printer module added•

Remove Ventilation slots from rear cover•

2009 July

V1.3a Notice sentence put below the specication• 2009 August

V1.4 B68 v1.0 and C48 v2.1 motherboard added• 2011 January

vi

Table of Contents

1. Packing List .............................. 1

1-1. Standard Accessories ..............................................1

1-2. Optional Accessories ...............................................2

2. System View ............................. 3

2-1. Front & Side View ....................................................3

2-2. Rear View ................................................................4

2-3. I/O Ports View ..........................................................5

3. System Assembly .................... 6

3-1. HDD replacement ....................................................6

3-2. SSD Card Replacement ..........................................7

3-3. RAM Replacement ..................................................8

4. Peripheral Installation ............. 9

4-1. MSR Installation ......................................................9

4-2. 2-in-1 MSR+Finger Print Module Installation ..........10

4-3. 2-in-1 MSR+iButton Module Installation ................. 11

4-4. VFD Installation ......................................................12

4-5. Second Display Installation ....................................13

4-6. Cash Drawer Installation .......................................14

4-6-1. For B78 motherboard .............................................. 14

4-6-2. For B68/C48 motherboard ....................................... 16

vii

5. Jumper Setting ........................ 18

5-1. For B78 Motherboard .............................................18

5-1-1. Motherboard Layout ................................................ 18

5-1-2. Connectors & Functions .......................................... 19

5-1-3. Jumper Setting ........................................................ 20

5-2. For B68 Motherboard .............................................23

5-2-1. Motherboard Layout ................................................ 23

5-2-2. Connectors & Functions .......................................... 24

5-2-3. Jumper Setting ........................................................ 26

5-3. For C48 Motherboard .............................................29

5-3-1. Motherboard Layout ................................................ 29

5-3-2. Connectors & Functions .......................................... 30

5-3-3. Jumper Setting ........................................................ 31

6. Specication ........................... 36

Appendix: Drivers Installation .... 38

viii

The page is intentionally left blank.

1

Packing List1.

Standard Accessories

1-1.

System a.

Driver bankb.

User guidec.

Power adapterd.

Power corde.

RJ45-DB9 cable (x2)f.

Note: Power cord will be supplied differently according to

various region or country.

a

b

c

d

e

f

2

Optional Accessories

1-2.

MSR modulea.

2-in-1 MSR+nger print moduleb.

2-in-1 MSR+iButton reader modulec.

2nd Display (with VGA / DB15 cable) d.

SSD modulee.

PCI-E WLAN Card (with internal antenna cable)f.

pSSD card (with bracket)g.

VFD module (with RJ-45 cable)h.

WLAN Card

a

b

c

d

e

f

g

h

pSSD Card

3

System View2.

Front & Side View

2-1.

Item No. Description

1 Touch screen

2 MSR module / 2-in-1 MSR module (Optional)

3 Power LED

4 Power button

5 HDD installation cover

6 Hinge for TFT-LCD

7 Ventilation

8 VFD / 2nd display installation place (Optional)

9 screw holes (x4) for 2nd display installation

1

2

3

4

5

7

8

9

10

11

12

13

6

4

Rear View

2-2.

Item No. Description

10 Speakers (x2) (Optional)

11 I/O ports

12 VESA mount holes (x4)

13 Robber foot (x4)

1

2

3

4

5

7

8

9

10

11

12

13

6

5

I/O Ports View

2-3.

Item No. Description

a 2nd VGA (Female)

b DC-In

c LAN

d Cash Drawer (12V/24V)

e MIC-in

f Line-out

g COM 1, 2, 3, 4 (from left to right)

h USB x 4

i Parallel

j Power Switch

b c d e f g h i j

a

6

System Assembly3.

Loose the thumb screw (x2) to open the HDD cover.1.

Disconnect the SATA cable of HDD.2.

Loosen the screws (x4) fixed the HDD module on the sheet metal chassis.3.

Loosen the screws (x4) on both sides of the HDD metal bracket and replace 4.

the HDD module.

HDD replacement

3-1.

7

SSD Card Replacement

3-2.

Loosen the thumb screw (x2) to open the HDD cover.1.

Fasten the screw (x2) to x the SSD module bracket on the sheet metal 2.

chassis.

Fasten the screw (x2) to x the SSD card on the SSD module bracket.3.

Connect the SATA cable to the SSD card.4.

8

Removing a RAM module

Use both fingers to pull the ejector 1.

clips out of the sides of the module.

Slide out to take out the memory 2.

module from the memory slot.

Installing a RAM module

Slide the memory module into the 3.

memory slot and press down until

it fix with the ejector clips.

RAM Replacement

3-3.

Please open the HDD cover and disconnect the HDD SATA cable to separate

them form the system. You will nd the motherboard. Please refer to the

motherboard layout to nd the memory compartment. (See chapter 5 for different

motherboard.)

9

Peripheral Installation4.

MSR Installation

4-1.

Loosen the screws (x3) to open the MSR cover on the TFT LCD.1.

The system provide 3 kinds of MSR for selections, MSR , 2-in-1 MSR+nger print

reader, 2-in-1 MSR+iButton reader.

Connect the cable of MSR module to the respective connector of the system 2.

and fix the ground cable.

Install the MSR module into the right position of the system.3.

Fasten the screws (x2) to fix the MSR reader module with the system.4.

10

2-in-1 MSR+Finger Print Module Installation

4-2.

Loosen the screws (x3) to open the MSR cover on the TFT LCD module as 1.

step 1 of Chapter 4-1.

Connect the cable of the 2-in-1 MSR + finger print module to the respective 2.

connector on the system.

Fasten the screws (x2) to fix the reader with the system.3.

11

2-in-1 MSR+iButton Module Installation

4-3.

Loosen the screws (x3) to open the MSR cover on the TFT LCD module as 1.

step 1 of Chapter 4-1.

Connect the cable of the 2-in-1 MSR + iButton reader module to the 2.

respective connector on the system.

Fasten the screws (x2) to fix the reader with the system.3.

12

Thread the VFD cable through the VFD pole and connect the RJ45 connector 1.

to the I/O panel of the system.

Connect the other side of the VFD cable to the VFD display and align the 2.

VFD display correctly to the screw holes of the VFD pole.

Insert the wheel shaft assembly into the aligning hole on the side of the VFD 3.

hinge and VFD Pole.

Tighten the plastic wheel with the shaft which comes out from the other side 4.

of the aligning hole.

VFD Installation

4-4.

VFD Pole

Screws (x2)

VFD Accessories

Screws (x2)

VFD Cable (RJ45)

VFD Display

Page is loading ...

Flytech POS365 User manual

Flytech POS365 User manual

Related papers

Other documents