Sharp PN-E471R Specification

Brand: Sharp

Model: PN-E471R

Category: LED displays

Type: Specification

This manual is also suitable for

PNE471R

PN-E471R

PN-E421

LCD MONITOR

OPERATION GUIDE

This guide contains instructions regarding operation, settings, and similar details.

For instructions regarding connection and installation, refer to the included Operation Manual.

Manual Scope

- Microsoft, Windows and Internet Explorer are registered trademarks of Microsoft Corporation.

- HDMI, the HDMI Logo and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing

LLC.

- Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United

States and/or other countries.

- This product comes with RICOH Bitmap Fonts produced and sold by RICOH COMPANY, LTD.

- All other brand and product names are trademarks or registered trademarks of their respective holders.

- Language of OSD menu used in this manual is English by way of example.

- Illustrations in this manual may not exactly represent the actual product or display.

- This manual assumes use in horizontal orientation, except where specically noted.

Contents

Part Names .......................................................................3

Basic Operation ...............................................................5

Menu Items .......................................................................7

Displaying the menu screen .........................................7

List of menu items ........................................................8

Menu item details .......................................................10

Adjustments for PC screen display ............................16

Initialization (Reset)/Functional Restriction Setting

(FUNCTION) ....................................................................17

Controlling the Monitor with a PC (RS-232C) ..............18

PC connection ............................................................18

Communication conditions .........................................18

Communication procedure .........................................18

Setting of the GAMMA user data ................................21

RS-232C command table ...........................................22

Controlling the Monitor with a PC (LAN) .....................29

Settings to connect to a LAN ......................................29

Controlling with a PC ..................................................31

Troubleshooting .............................................................37

Specications ................................................................38

Front view

2 345

1. LCD panel

2. Remote control sensor

3. Input switch (See page 5.)

4. Power switch

5. Power LED

TIPS

• Use a pointed object such as a pen tip to press the

switches at the front of the monitor.

Part Names

Rear view

When the PN-ZB01 (optional)

is attached

18171615 19

10 11

2120 2423

1. AC input terminal

2. Main power switch

3. PC/AV HDMI input terminal

4. PC D-sub input terminal

5. Audio input terminal

6. Audio output terminals

7. RS-232C output terminal

8. RS-232C input terminal

9. Optional terminal

This terminal is provided for possible future (optional)

function expansion. Offering of this terminal is not a

guarantee that future expanded functionality will be

provided.

10. Expansion terminal cover

Additional input/output terminals are available by attaching

the PN-ZB01 interface expansion board (optional).

11. Optional attachment section

This section is used to connect optional hardware for

function expansion. Offering this attachment location

is not a guarantee that future compatible hardware

attachments will be released.

12. Speakers

13. Handles

14. Vents

When the PN-ZB01 (optional) is attached

15. PC/AV DVI-D input terminal

16. PC/AV DVI-D output terminal

17. LAN terminal

18. External speaker terminals

19. Audio 1 input terminals

20. Audio 2 input terminals

21. PC RGB input terminals

22. AV component input terminals

23. AV video input terminal

24. AV S-video input terminal

Caution

• Consult your SHARP dealer for attachment/detachment of

optional parts.

• Do not open the expansion terminal cover by yourself.

There are high voltage parts inside the cover which may

cause an electric shock.

Part Names

Remote control unit

1. Signal transmitter

2. POWER button

3. DISPLAY button (See page 5.)

4. MUTE button (See page 5.)

5. VOL +/- buttons (See page 5.)

BRIGHT +/- buttons (See page 5.)

Cursor control (

/ / / ) buttons

6. INPUT button (See page 5.)

7. MODE button (See page 5.)

8. SIZE button (See page 5.)

9. MENU button (See page 5.)

Basic Operation

1. INPUT (Input mode selection)

The menu is displayed. Press

or to select the input

mode, and press

to enter.

* You can select the input terminal by pressing the input

switch of the monitor.

Input mode Video Audio

PC D-SUB PC D-sub input terminal

Audio input terminal

PC HDMI

PC/AV HDMI input terminal

AV HDMI

PC/AV HDMI input terminal

When the PN-ZB01 (optional) is attached

Input mode Video Audio

PC DVI-D

PC/AV DVI-D input terminal

PC HDMI

PC/AV HDMI input terminal

PC D-SUB

PC D-sub input terminal

PC RGB

PC RGB input terminals

AV DVI-D

PC/AV DVI-D input terminal

AV HDMI

PC/AV HDMI input terminal

AV COMPONENT

AV COMPONENT input terminals

AV S-VIDEO AV S-video input terminal

AV VIDEO AV video input terminal

*1 Select the terminal to be used in HDMI of INPUT SELECT.

(See page 12.)

*2 Select the terminal for AUDIO SELECT which is used for

audio input. (See page 12.)

*3 Select the terminal to be used in DVI of INPUT SELECT.

(See page 12.)

*4 Select the terminal to be used in BNC of INPUT SELECT.

(See page 12.)

2. DISPLAY

Displays monitor information. When you press this button

again, the display disappears.

When the PN-ZB01 (optional) is attached, the display changes

from INFORMATION1 → INFORMATION2 → clear display,

and so on every time you press this button.

• The display disappears automatically after about 15

seconds.

•

LAN

is displayed during LAN communication.

• If

LAN

is displayed in red, there is a duplicate IP address.

3. MODE (Color mode selection)

Each time you press this button, the color mode changes in

the following order:

STD (Standard) → VIVID → sRGB → STD...

• sRGB applies to PC input only.

sRGB is international standard of color representation

specied by IEC (International Electrotechnical

Commission). Color conversion is made in taking account

of liquid crystal’s characteristics and represents color tone

close to its original image.

4. SIZE (Screen size selection)

The menu is displayed.

Press

or to select the screen size. (See page 6.)

5. MUTE

Turns off the volume temporarily.

Press the MUTE button again to turn the sound back to the

previous level.

6. MENU

Displays and turns off the menu screen (see page 7).

7. VOL +/- (Volume adjustment)

Pressing

or displays the VOLUME menu when the

menu screen is not displayed.

V OLUME 15

Press or to adjust the volume of the sound.

* If you do not press any buttons for about 4 seconds, the

VOLUME menu automatically disappears.

8. BRIGHT +/- (Backlight adjustment)

Pressing

or displays the BRIGHT menu when the menu

screen is not displayed.

BRIGHT 15

Press or to adjust the brightness.

* If you do not press any buttons for about 4 seconds, the

BRIGHT menu automatically disappears.

Basic Operation

Switching the screen size

Even when the screen size is changed, the display may remain the same depending on the input signal.

WIDE PC input Displays image so it lls the entire screen.

AV input An image with a 4:3 aspect ratio is stretched to ll the entire

screen.

ZOOM 1

PC input An image with a 4:3 aspect ratio is enlarged to ll the entire screen

without changing the aspect ratio. The edges of the image may be

cut off.

AV input

ZOOM 2

PC input Use this size if ZOOM 1 cuts off the subtitles.

AV input

NORMAL

PC input Displays image so it lls the screen without changing the aspect

ratio of the input signals.

AV input Displays the entire image of the aspect ratio of 4:3 without

changing the aspect ratio.

Dot by Dot

PC input Displays the dots of the signals input from the connected PC as

the corresponding dots on the screen. *

AV input Displays the dots of the input signals as the corresponding dots on

the screen.

*: With a monitor of screen resolution 1600 x 1200 or 1920 x 1200, selecting Dot by Dot displays the NORMAL screen.

TIPS

• Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial

or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright

Law, so please be careful.

• When “Enlarge” is set, the screen size is xed to “WIDE” mode.

• When dual-screen display is selected, the screen size cannot be changed.

• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original

image (e.g. TV broadcast or video input from external equipment).

• When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this

monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen

size to “NORMAL”.

• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen

size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the

edges of the screen. This is due to the characteristics of the software, and is not a malfunction.

• Depending on the original image size, black bands may remain at the edges of the screen.

Menu Items

Displaying the menu screen

Video and audio adjustment and settings of various functions

are enabled. This section describes how to use the menu

items. See pages 10 to 13 for details of each menu items.

Caution

• Do not turn the main power switch off while the menu items

are being displayed. Doing so may initialize the settings.

Example of operation

(Adjusting CONTRAST in the PICTURE menu)

1. Press

to display the menu screen.

1920x1080

V: 60 Hz H: 67.5 kHz

AUTO

CLOCK

PHASE

H-POS

V-POS

H-SIZE

V-SIZE

H-RESOLUTION

V-RESOLUTION

RESET

SCREEN

PICTURE

AUDIO

SETUP

OPTION

ENLARGE

PIP/PbyP

600

610

1920

1080

SCREEN 1/1

END···[MENU]

PC D-SUB

2. Press or to select PICTURE, and press .

PICTURE menu is displayed.

3. Press

or to select CONTRAST.

AUTO

CONTRAST

BLACK LEVEL

TINT

COLORS

SHARPNESS

1/2

PICTURE

SCREEN

PICTURE

AUDIO

SETUP

OPTION

ENLARGE

PIP/PbyP

OK···[MENU]

1920x1080

V: 60 Hz H: 67.5 kHz

PC D-SUB

4. Press or to adjust the setting.

AUTO

CONTRAST

BLACK LEVEL

TINT

COLORS

SHARPNESS

1/2

PICTURE

SCREEN

PICTURE

AUDIO

SETUP

OPTION

ENLARGE

PIP/PbyP

OK···[MENU]

V: 60 Hz H: 67.5 kHz

1920x1080

PC D-SUB

For items that have , press , make settings and then

press

5. Press

twice to close the menu screen.

TIPS

• The menu will differ depending on the input mode.

• The menu screen will close automatically if no operation is

performed for about 15 seconds. (DATE/TIME SETTING,

SCHEDULE and LAN SETUP screens will close in about 4

minutes.)

Menu screen display

AUTO

CONTRAST

BLACK LEVEL

TINT

COLORS

SHARPNESS

1/2

PICTURE

SCREEN

PICTURE

AUDIO

SETUP

OPTION

ENLARGE

PIP/PbyP

OK···[MENU]

V: 60 Hz H: 67.5 kHz

1920x1080

PC D-SUB

1 3 2

1 Name of the menu

2 Input mode

3 An item being selected (highlighted)

4 Screen resolution of input signal, and other data.

TIPS

• Items that cannot be selected appear in gray.

(e.g. Function not supported by the current input signal)

Menu Items

List of menu items

The displayed menu items vary depending on whether or not the PN-ZB01 (optional) is attached.

○: Item is available, -: Item is not available.

Menu Item

PN-ZB01 (optional)

Not attached Attached

SCREEN AUTO ○ ○

CLOCK ○ ○

PHASE ○ ○

H-POS ○ ○

V-POS ○ ○

H-SIZE ○ ○

V-SIZE ○ ○

H-RESOLUTION ○ ○

V-RESOLUTION ○ ○

RESET ○ ○

PICTURE AUTO ○ ○

CONTRAST ○ ○

BLACK LEVEL ○ ○

TINT ○ ○

COLORS ○ ○

SHARPNESS ○ ○

ADVANCED FLESH TONE ○ ○

3D-NR ○ ○

MPEG-NR ○ ○

3D-Y/C - ○

C.M.S.-HUE ○ ○

C.M.S.-SATURATION ○ ○

C.M.S.-VALUE ○ ○

COLOR MODE ○ ○

WHITE BALANCE ○ ○

PRESET ○ ○

R-CONTRAST ○ ○

G-CONTRAST ○ ○

B-CONTRAST ○ ○

COPY TO USER ○ ○

GAMMA ○ ○

RESET ○ ○

AUDIO TREBLE ○ ○

BASS ○ ○

BALANCE ○ ○

RESET ○ ○

SETUP OSD H-POSITION ○ ○

OSD V-POSITION ○ ○

MONITOR ○ ○

MONAURAL AUDIO ○ ○

LANGUAGE ○ ○

POWER ON DELAY ○ ○

STANDBY MODE ○ ○

HDMI SETTING HDMI AUTO VIEW ○ ○

HDMI RGB INPUT RANGE ○ ○

HOT PLUG CONTROL HDMI ○ ○

DVI - ○

RS-232C/LAN SELECT - ○

ID No. SET ○ ○

BAUD RATE ○ ○

LAN SETUP - ○

SPEAKER SELECT - ○

OPTION DC OUT SETTING ○ ○

Menu Item

PN-ZB01 (optional)

Not attached Attached

OPTION DATE/TIME SETTING ○ ○

SCHEDULE ○ ○

INPUT SELECT DVI - ○

BNC - ○

HDMI ○ ○

AUDIO SELECT PC DVI-D - ○

PC HDMI ○ ○

PC D-SUB - ○

PC RGB - ○

AV DVI-D - ○

AV HDMI ○ ○

AV COMPONENT - ○

AV S-VIDEO - ○

AV VIDEO - ○

INPUT SIGNAL 480 LINES ○ ○

768 LINES ○ ○

1050 LINES ○ ○

ZOOM2 SPECIAL SETTING ○ ○

SCAN MODE ○ ○

POWER MANAGEMENT ○ ○

COLOR SYSTEM - ○

AUDIO OUTPUT ○ ○

AUDIO INPUT LEVEL ○ ○

SELF ADJUST ○ ○

AUTO INPUT CHANGE ○ ○

ENLARGE ENLARGE H ○ ○

ENLARGE V ○ ○

ENLARGE-POS H ○ ○

ENLARGE-POS V ○ ○

BEZEL H ○ ○

BEZEL V ○ ○

H-POS ○ ○

V-POS ○ ○

PIP/PbyP PIP MODES ○ ○

PIP SIZE ○ ○

PIP H-POS ○ ○

PIP V-POS ○ ○

PIP BLEND ○ ○

PIP SOURCE - ○

SOUND CHANGE ○ ○

MAIN POS ○ ○

PbyP2 POS ○ ○

AUTO OFF ○ ○

TIPS

• Some items may not be displayed depending on the input mode.

Menu Items

Menu item details

The menu will differ depending on the input mode.

SCREEN

AUTO (PC D-SUB/PC RGB)

The CLOCK, PHASE, H-POS, and V-POS are automatically

adjusted.

Pressing

performs adjustment.

Use this automatic adjustment when you use the PC D-sub

input terminal or PC RGB input terminals to display a PC

screen for the rst time or when you change the setting of

the PC. (See page 16.)

CLOCK (PC D-SUB/PC RGB)

Adjusts frequency for sampling clock for applicable video.

Adjust when there is ickering in the form of vertical stripes.

When using the adjustment pattern (see page 16), make

adjustments so that no vertical stripe noise appears in it.

PHASE (PC D-SUB/PC RGB)

Adjusts sampling clock phase for applicable video.

Useful when small characters appear with low contrast and/

or there are ickers at corners.

When using the adjustment pattern (see page 16), make

adjustments so that no horizontal stripe noise appears in it.

* Adjustments to PHASE should be made only after CLOCK

has been correctly set.

H-POS

Adjust the horizontal position of the image.

V-POS

Adjust the vertical position of the image.

H-SIZE

Adjust the horizontal size of the image.

V-SIZE

Adjust the vertical size of the image.

H-RESOLUTION (PC D-SUB/PC RGB)

Sets proper horizontal resolution when the resolution of

input signals is not recognized properly. (Adjustment may be

impossible with some signals.)

V-RESOLUTION (PC D-SUB/PC RGB)

Sets proper vertical resolution when the resolution of input

signals is not recognized properly. (Adjustment may be

impossible with some signals.)

RESET

Resets the values of the SCREEN menu items to the factory

preset values.

Select “ON” and then press

PICTURE

AUTO (PC D-SUB/PC RGB)

The CONTRAST and BLACK LEVEL are automatically

adjusted.

Pressing

performs adjustment.

CONTRAST

Adjusts the brightness of the image.

BLACK LEVEL

Adjusts the entire brightness of the video signals.

TINT

Adjusts the hue. Selecting + changes the color towards

green, and selecting - changes it towards magenta.

COLORS

Adjusts the color intensity.

SHARPNESS

Adjusts the sharpness of the image.

ADVANCED (AV input)

You can adjust more specically. (See page 16.)

COLOR MODE

Changes the color mode on the screen. The color mode on

the screen can also be changed using a remote control unit.

(See page 5.)

* sRGB is PC input only. See page 5 for details.

WHITE BALANCE

THRU .............. Displays the input signal level as is. (for PC

DVI-D/PC HDMI only)

PRESET ......... Selects the color temperature using PRESET.

USER .............. Used for adjusting R-CONTRAST,

G-CONTRAST, and B-CONTRAST

respectively.

PRESET

Selects the color temperature when the WHITE BALANCE is

set to PRESET.

The setting values are shown for reference. The color

temperature of the screen varies over time.

This function is not intended to keep the color temperature

constant.

R-CONTRAST

Adjusts red component when the WHITE BALANCE is set to

USER.

G-CONTRAST

Adjusts green component when the WHITE BALANCE is set

to USER.

B-CONTRAST

Adjusts blue component when the WHITE BALANCE is set

to USER.

COPY TO USER

Copies the value set for PRESET to the USER setting.

Select “ON” and then press

GAMMA

Select a gamma value. USER sets the gamma value

transferred by the user. (See page 21.)

RESET

Resets the values of the PICTURE menu items to the factory

preset values.

Select “ON” and then press

Menu Items

AUDIO

TREBLE

Adjusts the volume of treble-level sound.

BASS

Adjusts the volume of bass-level sound.

BALANCE

Adjusts the balance of the audio sound between right and left.

RESET

Resets the values of the AUDIO menu items to the factory preset values.

Select “ON” and then press .

SETUP

OSD H-POSITION

Adjusts the horizontal display position of menu screen.

OSD V-POSITION

Adjusts the vertical display position of menu screen.

MONITOR

Select the installation direction of the monitor.

LANDSCAPE ............Horizontal orientation

PORTRAIT ...............Vertical orientation

MONAURAL AUDIO

Outputs audio signals as monaural.

LANGUAGE

Sets the display language for the menu screen.

POWER ON DELAY

You can delay the screen display after the monitor is turned

on. The period can be set up to 60 seconds in units of one

second. When this function is activated, the power LED

ashes (at approx. 1 second interval) in orange. This function

is disabled when 0 is specied.

STANDBY MODE

When STANDARD is selected, startup time from standby

mode is reduced. Note, however that, more power will be

consumed in standby mode.

When LOW POWER is selected, current consumption

is reduced while the monitor is in standby mode. Note,

however, that the startup time from standby mode becomes

longer. Also, certain RS-232C commands cannot be used

in standby mode, and control via LAN will be disabled. (See

pages 22 and 29.)

HDMI SETTING

HDMI AUTO VIEW

......................... When ON is selected, the screen size is

adjusted automatically according to the

screen size control signal included in the

video signal input from the AV HDMI input

terminal.

HDMI RGB INPUT RANGE

......................... Sets the type of HDMI signals when using

the AV HDMI input mode.

When AUTO is selected, the type is set

automatically.

HOT PLUG CONTROL

Sets whether to use hot plug control for the PC/AV HDMI

and PC/AV DVI-D input terminals.

RS-232C/LAN SELECT

Selects the method with which to control the monitor from

the computer.

ID No. SET

Assigns ID numbers to monitors connected in a daisy chain

(see page 19), using RS-232 cables.

The numbers 1 to 255 are available for ID numbers.

If “0” is set, the system regards this as the state where no ID

number is set.

BAUD RATE

Selects the communication speed used for RS-232C

communication.

LAN SETUP

Congures the settings to control the monitor from the

computer via LAN. (See page 29.)

SPEAKER SELECT

Selects the speaker to be used.

OPTION DC OUT SETTING

Normally, leave this setting as OFF.

When using an optional part, if instruction appears, change

the setting accordingly.

Menu Items

AUTO INPUT CHANGE

Specify whether to change inputs automatically. When ON is

selected and no signal is present in the selected input mode,

AUTO INPUT CHANGE automatically changes the selected

mode to another mode where a video signal is present.

When video signals exist in multiple input modes, the

switching priority is as follows:

PC D-SUB, PC HDMI and AV HDMI

When the PN-ZB01 (optional) is attached:

PC DVI-D, PC HDMI, PC D-SUB, PC RGB, AV DVI-D, AV

HDMI, AV COMPONENT, AV S-VIDEO and AV VIDEO

(Input mode switching may take 15 seconds or more,

depending on the connected equipment. Input signals

may not be detected properly and a priority may change,

depending on the connected equipment or video signals.)

ENLARGE (PC input)

ENLARGE H

Sets the number of screen splits (number of monitors) in the

horizontal direction used for the enlargement. (See page 14.)

ENLARGE V

Sets the number of screen splits (number of monitors) in the

vertical direction used for the enlargement. (See page 14.)

ENLARGE-POS H / ENLARGE-POS V

Specify the split screen to be displayed when the

enlargement function is used. (See page 14.)

BEZEL H / BEZEL V

Sets the frame width of the display when the enlargement

function is used.

H-POS

Adjust the horizontal position of the enlarged screen.

V-POS

Adjust the vertical position of the enlarged screen.

OPTION

DATE/TIME SETTING

Set the date and time. Press

or to select the date and

time, and press

or to change the numerical values.

Set the date in “Year/Month/Day” order.

Set the time on a 24-hour basis.

SCHEDULE (See page 15.)

You can set the time to switch the monitor on and off.

INPUT SELECT

Select the input mode to be used in PC/AV DVI-D input

terminal, PC/AV HDMI input terminal and PC RGB/AV

component input terminals.

AUDIO SELECT

Selects the terminal used to input audio signals in each input

mode.

INPUT SIGNAL (PC D-SUB/PC RGB)

If a computer connected to the PC D-sub/PC RGB input

terminal outputs any of the following resolutions, make a

selection from the following options.

480 LINES .......... AUTO, 640x480 or 848x480

768 LINES ..........AUTO, 1024x768, 1280x768, or 1360x768

1050 LINES ........1400x1050 or 1680x1050

ZOOM2 SPECIAL SETTING (See page 14.)

SCAN MODE (AV input)

Sets the scan mode used for AV mode input.

MODE1 ............... Over-scan display

MODE2 ...............Under-scan display

MODE3 ............... Under-scan display when the input signal

is 1080i/p. Otherwise, over-scan display

Even when MODE1 is selected, under-scan display is used when

the input signal is 1080i/p and the screen size is Dot by Dot.

POWER MANAGEMENT

POWER MANAGEMENT determines whether or not to

switch modes from no signal to the input signal standby

mode.

COLOR SYSTEM (AV S-VIDEO/AV VIDEO)

Select the color system of the AV equipment which is

connected to AV S-video and AV video input terminal. (AUTO

/ PAL / PAL-60 / SECAM / NTSC3.58 / NTSC4.43)

When AUTO is selected, the color system is automatically

set according to the input signal.

AUDIO OUTPUT

Sets the volume of sound output from the audio output

terminals.

VARIABLE .......... You can adjust the volume using VOLUME.

FIXED .................Fixes the sounds.

AUDIO INPUT LEVEL

Selects the maximum audio input level of the audio input

terminal.

SELF ADJUST

On a PC D-SUB/PC RGB screen, specify whether to

perform screen adjustment automatically or not. When ON

is selected, the screen is automatically adjusted when its

resolution is 800 x 600 or higher and the timing of input

signals changes. “ADJUSTING” appears on the screen

during the adjustment. Depending on the signal, adjustment

may not be possible. In this case select OFF. (Perform

manual adjustment of the screen.)

Menu Items

PIP/PbyP

PIP MODES

Sets the display method.

OFF .........Displays one screen.

PIP ...........Displays a sub screen inside a main screen.

PbyP ........Displays a main screen and a sub screen in a line.

PbyP2 ......

Displays a main screen which measures 1280 pixels

in the longest direction and a sub screen in a line.

PIP SIZE

Sets the size of the sub screen in PIP mode.

PIP H-POS

Adjusts the horizontal position of the sub screen in PIP mode.

PIP V-POS

Adjusts the vertical position of the sub screen in PIP mode.

PIP BLEND

In PIP mode, use this menu item to display the sub screen

transparently.

PIP SOURCE

Selects the input signal of the sub screen in PIP, PbyP, or

PbyP2 mode.

SOUND CHANGE

Sets the sound which is output in PIP, PbyP, or PbyP2 mode.

If the main screen is displayed as a full screen by the AUTO

OFF function, the sound for the main screen is output even

when the sound for the sub screen is specied.

MAIN POS

Sets the position of the main screen in PbyP or PbyP2 mode.

PbyP2 POS

Sets the position of the sub screen in PbyP2 mode.

AUTO OFF

Sets the display method when no signals for the sub screen

are input in PIP, PbyP, or PbyP2 mode.

MANUAL .......

Displays a main screen and a black sub screen.

AUTO ............Displays the main screen as a full screen.

TIPS

• When WHITE BALANCE is set to THRU, BLACK LEVEL,

CONTRAST, TINT, COLORS and GAMMA cannot be set.

• If COLOR MODE is set to sRGB or VIVID, the following

items cannot be set.

WHITE BALANCE, PRESET, R-/G-/B-CONTRAST, COPY

TO USER, and GAMMA

• If GAMMA is set to USER, the following items cannot be

set.

WHITE BALANCE, PRESET, R-/G-/B-CONTRAST, and

COPY TO USER

• STANDBY MODE cannot be set to LOW POWER when

SCHEDULE is effective or when OFF is selected for LED in

FUNCTION.

Dual screen display

You can display the screens of the PC input signal and AV

input signal simultaneously.

Set this function with “PIP MODES” in the PIP/PbyP menu.

PIP

Main screen

Sub

screen

A sub screen is displayed

inside a main screen.

PbyP

Main

screen

Sub

screen

A main screen and a sub

screen are displayed in a

line.

PbyP2

Main screen

Sub

screen

Displays a main screen

which measures 1280

pixels in the longest

direction and a sub

screen in a line.

* The currently selected input signal is displayed on the main

screen.

* You cannot simultaneously display the screens of signals

of the same type, such as two types of PC input signals or

two types of AV input signals.

* The dual screen display cannot be used with the

combination of PC DVI-D and AV HDMI or of AV DVI-D and

PC HDMI.

TIPS

• You might infringe on a copyright of the author which is

protected by copyright law when you display the images of

the computer screen and television/VCR simultaneously for

prot-making or to show the image to the public.

• The screen size for dual-screen display is the same as

the screen size for single-screen display. The Dot by Dot

screen is displayed in NORMAL size except when it is set

as the PIP main screen.

• When dual-screen display is selected, the AUTO INPUT

CHANGE function is disabled.

• When dual-screen display is selected, the screen cannot

be enlarged.

• When dual-screen display is selected, the INPUT SELECT

options cannot be set.

Menu Items

Enlarge

• You can align several monitors and integrate them into a

single large screen to display.

• Up to ve monitors can be aligned in both the horizontal

and vertical directions.

• Each monitor displays enlarged views of separated images.

(Example)

Horizontal direction: 2 monitors

Vertical direction: 2 monitors

Horizontal direction: 3 monitors

Vertical direction: 2 monitors

Setting procedure

In the ENLARGE menu, set ENLARGE H/V and

ENLARGE-POS H/V. (See page 12.)

1. Set the number of monitors aligned in the horizontal

direction in ENLARGE H.

2. Set the number of monitors aligned in the vertical

direction in ENLARGE V.

3. Set the section of the separated image to be displayed

on each monitor in ENLARGE-POS H and

ENLARGE-POS V.

In horizontal orientation

ENLARGE H

(1,2)

(1,3)

(1,4)

(2,2)

(2,3)

(2,4)

(3,2)

(3,3)

(3,4)

(4,2)

(4,3)

(4,4)

(1,1)

(2,1)

(3,1)

(5,2)

(5,3)

(1,5)(2,5) (3,5)(4,5) (5,5)

(5,4)

(5,1)

(4,1)

ENLARGE V

In vertical orientation

ENLARGE V

(2,1)(3,1)(4,1)

(2,2)(3,2)(4,2)

(2,3)(3,3)(4,3)

(2,4)(3,4)(4,4)

(1,1)

(1,2)

(1,3)

(2,5)(3,5)

(5,1)

(5,2)

(5,3)

(5,4)

(5,5) (4,5

)(

1,5)

(1,4)

ENLARGE H

* The numbers in parentheses are the setting values in

(ENLARGE-POS H, ENLARGE-POS V) format.

TIPS

• AV input signals cannot be used for the Enlarge function.

• When Enlarge is used, the AUTO INPUT CHANGE function

is disabled.

• To cancel the enlargement, set 1 for ENLARGE H and

ENLARGE V respectively.

ZOOM2 SPECIAL SETTING

If you connect a laptop computer with any of the following

screen resolutions and black bands appear around the

screen, set ZOOM2 SPECIAL SETTING of INPUT SIGNAL on

the OPTION menu to ON and then select ZOOM2 in the SIZE

setting.

This displays the area inside the black band.

Laptop computer

resolution

Corresponding signal*

1280x800 1280x1024, 1280x960, 1400x1050*

1280x600 1280x720

1024x600 1024x768

*1: This setting is effective only when the screen resolution,

including the black band, is one of the resolutions listed

above.

*2: Use the automatic screen adjustment.

SCHEDULE

You can set the time to switch the monitor on and off.

Set this function with “SCHEDULE” in the OPTION menu. (See

page 12.)

SCHEDULE

No. POWER DAY OF THE WEEKTIME INPUT

XXXX/XX/XX XXX XX:XX:XX

(2)

…

[MENU]

1920x1080

V: 60 Hz H: 67.5 kHz

(1)

(3) (4) (5)

PC D-SUB

1. Press or to select the SCHEDULE number, and

press

2. Set the SCHEDULE. (See the description below.)

Press

or to select items, and press or to

change the setting.

3. Press

SCHEDULE becomes effective.

(1)

●: SCHEDULE effective

: SCHEDULE not effective

(2) POWER

ON : Switches the monitor on at the specied time.

OFF : Switches the monitor off at the specied time and puts

the monitor in standby mode.

(3) DAY OF THE WEEK

Species the day of the week to execute the SCHEDULE.

ONLY ONCE:

Executes the SCHEDULE once on the specied day.

Specify the day of the week to execute the SCHEDULE.

EVERY WEEK:

Executes the SCHEDULE on the specied day of the week

every week. Specify the day of the week to execute the

SCHEDULE.

Periodic setting such as “Monday through Friday” is also

possible.

EVERY DAY:

Executes the SCHEDULE every day regardless of the day

of the week.

(4) TIME

Species the time to execute the SCHEDULE.

Set the time on a 24-hour basis.

(5) INPUT

Species the input mode at power-on. When not specifying,

the screen at the previous power-off appears.

Input modes displayed on DVI, HDMI and BNC depend on

INPUT SELECT settings.

Menu Items

Caution

• Do not switch off the main power after setting the

SCHEDULE.

• Specify the correct date and time. (See page 12.)

SCHEDULE does not function unless the date and time are

specied.

• Check regularly that the set date and time are correct.

• When STANDBY MODE is LOW POWER, SCHEDULE

cannot be set.

TIPS

• Up to 8 SCHEDULE items can be registered.

• Setting the SCHEDULE ashes the power LED alternately

in red and orange in standby mode.

• A SCHEDULE that has a large number has precedence

over that of a small number when schedules overlap.

ADVANCED items (AV input) (See page 10

for additional Menu item details.)

FLESH TONE

Adjust the hue control.

3D-NR

Reduce the noise of playback images on video.

Setting a higher level reduces more noise. However, it may

cause blurring on an image.

MPEG-NR

Reduce block noise caused by digital compression.

3D-Y/C (AV VIDEO)

Specify whether to perform 3-dimension Y/C separation.

If dot interference or cross-color is occurring in fast-motion

scenes, selecting “OFF” may improve the image quality.

C.M.S.-HUE

Adjusts color tone with 6 colors of R (red), Y (yellow), G

(green), C (cyan), B (blue), and M (magenta).

C.M.S.-SATURATION

Adjusts color vividness with 6 colors of R (red), Y (yellow), G

(green), C (cyan), B (blue), and M (magenta).

C.M.S.-VALUE

Adjusts color brightness with 6 colors of R (red), Y (yellow),

G (green), C (cyan), B (blue), and M (magenta).

TIPS

• When FLESH TONE is set to LOW or HIGH, C.M.S.-HUE/

-SATURATION/-VALUE cannot be set.

Adjustments for PC screen display

Automatic adjustment

When you use the PC D-sub input terminal or PC RGB input

terminals to display a PC screen for the rst time, or when

you change the setting of the PC, use the automatic screen

adjustment.

1. Switch the input to PC D-SUB or to PC RGB and display

the adjustment pattern. (See the description below.)

2. Press

and use or to display the SCREEN

menu.

3. Press

and select “AUTO”.

4. Press

The automatic adjustment is complete in several seconds.

5. Press

twice to close the menu screen.

TIPS

• If the screen cannot be adjusted properly with one

automatic adjustment, repeat the automatic adjustment two

or three times. Try manual adjustment if necessary.

Screen display for adjustment

Before making adjustments in the SCREEN menu or

PICTURE menu, display an image to brighten the entire

screen. If you are using a Windows PC, use the adjustment

pattern on the supplied CD-ROM.

Opening the adjustment pattern

The following example is performed in Windows XP.

1. Load the supplied CD-ROM into the computer’s CD-

ROM drive.

2. Open the CD-ROM in [My Computer].

3. Double-click [Adj_uty.exe].

The adjustment pattern will appear.

Adjust the screen automatically or manually.

4. Whenadjustmentisnished,pressthe[Esc]onthe

computer’s keyboard to quit the adjustment program.

5. Eject the CD-ROM from the CD-ROM drive.

TIPS

• If the display mode on the computer you are using is

65,000 colors, the color levels in the color pattern may

appear differently or grayscale may appear to be colored.

(This is due to the specications of the input signal and is

not a malfunction.)

Menu Items

You can return the settings to their factory-preset values and

restrict operations.

1. After pressing

for about 5 seconds, press , ,

, and in that order.

OFF

UNLOCKED

LED

OFF

MONITOR

FUNCTION

1/1

ALL RESET

ADJUSTMENT LOCK

RS-232C

OSD DISPLAY

LED

TEMPERATURE ALERT

STATUS ALERT

POWER BUTTON

CONTROLLER INPUT

END

…

[MENU]

2. Select and set the items.

ALL RESET

Resets the settings to the factory default settings.

Press

, select ALL RESET, and then press .

After initialization, turn the main power switch off and

then back on.

When the PN-ZB01 (optional) is attached, press

select the resetting method, and then press

ALL RESET1 ....Resets all the settings to the factory

default settings.

ALL RESET2 ....Returns all settings to the factory default

settings except for the following items:

LAN SETUP, RS-232C/LAN SELECT,

ID No. SET, BAUD RATE, NETWORK,

MAIL, SERVICE & SUPPORT, and

SNMP (See page 11, and pages 33 to

36.)

ADJUSTMENT LOCK

You can disable operations on the monitor and the

remote control unit that use buttons.

OFF ...Enables operation.

1.........Disables all operations other than turning power

on/off and FUNCTION.

2.........Only the FUNCTION operation is enabled.

Disables all operations other than FUNCTION (not

even power on/off).

RS-232C

(RS-232C/LAN when the PN-ZB01 (optional) is

attached)

Species whether to allow control via RS-232C or LAN

(see pages 18 and 29).

OSD DISPLAY

Hides/shows menus.

The FUNCTION screen cannot be hidden.

LED

Species whether to light the power LED.

OFF cannot be selected when STANDBY MODE is LOW

POWER.

Initialization (Reset)/Functional Restriction Setting (FUNCTION)

TEMPERATURE ALERT

Selects the notication method for an abnormal

temperature.

OFF ..............Do not notify about an abnormal

temperature.

OSD & LED ..When an abnormal temperature is

detected, the power LED ashes in red

and green alternately and the screen

displays a message: TEMPERATURE.

LED...............When an abnormal temperature is

detected, the power LED ashes in red

and green alternately.

STATUS ALERT

Selects the notication method for a hardware error.

OFF ..............Do not notify about the error.

OSD & LED ..When a hardware error is detected, the

power LED ashes in red and the screen

displays a message: STATUS [xxxx].

LED...............When a hardware error is detected, the

power LED ashes in red.

POWER BUTTON

Normally, leave this setting as MONITOR.

When using an optional part, if instruction appears,

change the setting accordingly.

CONTROLLER INPUT

Normally, you do not need to change this setting.

When using an optional part, if instruction appears,

change the setting accordingly.

3. Press

to return to the normal screen.

TIPS

• When both abnormal temperature and hardware error are

detected, the hardware error notication overrides.

Controlling the Monitor with a PC (RS-232C)

You can control this monitor from a PC via RS-232C (COM

port) on the PC.

You can also connect multiple monitors via a daisy chain by

using a PC. By assigning ID numbers to each monitor (see

page 19), you can make input mode selection/adjustment or

can check the status of a specic monitor.

Precautions when the PN-ZB01 (optional) is attached

• To control the monitor via RS-232C, set RS-232C/LAN

SELECT to RS-232C.

• You cannot use RS-232C and LAN control simultaneously.

PC connection

One-to-one connection with a PC

Connect with RS-232 straight cable between the PC’s COM

port (RS-232C connector) and the RS-232C input terminal on

the monitor.

RS-232 straight cable

(commercially available)

To COM port

RS-232C input terminal

Daisy chain connection…

Advanced operation

Connect with RS-232 straight cable between the PC’s COM

port (RS-232C connector) and the RS-232C input terminal on

the rst monitor.

Next, connect RS-232 straight cable to the rst monitor’s

RS-232C output terminal and to the second monitor’s

RS-232C input terminal. Connect in the same way to the third

and subsequent monitors.

Up to 25 monitors can be connected. (Depending on the

length of the cable used and the surrounding environment.)

RS-232 straight cables

(commercially available)

First monitor Second monitor

To COM port

RS-232C

input terminal

RS-232C

output terminal

Communication conditions

Set the RS-232C communication settings on the PC to match

the monitor’s communication settings as follows:

Baud rate *

Stop bit

1 bit

Data length 8 bits Flow control None

Parity bit None

* Set to the same baud rate as the BAUD RATE setting of

SETUP menu. (Initial setting: 9600 bps)

* When connecting multiple monitors in a daisy chain, set all

monitors to the same BAUD RATE.

Communication procedure

Command format

When a command is sent from the PC to the monitor, the

monitor operates according to the received command and

sends a response message to the PC.

C1 C2 C3 C4 P1 P2 P3 P4

Return code

Command field

(4 prescribed

alphanumerical characters

)

Parameter field

(4 character string comprised of:

0-9, +, -, space, ?)

Example: VOLM0030

VOLM

* Be sure to input 4 characters for the parameter. Pad with

spaces (“

”) if necessary.

(“

” is a return code (0D

, 0A

or 0D

))

Wrong : VOLM30

Right : VOLM 30

When inputting a negative value, specify a numerical value in

three digits.

Example: AUTR-009

Do not use spaces for MPOS, DATE, and SC01 through

SC08. Specify parameters using a specied number of

characters.

Example: MPOS010097

If a command has “R” listed for “DIRECTION” in the

“RS-232C command table” on page 22, the current value can

be returned by using “?” as the parameter.

Example:

VOLM ? ? ? ? ←

From PC to monitor (How much

is current volume setting?).

30 ←

From monitor to PC (Current

volume setting: 30).

* If an ID number (see page 19) has been assigned

(For example, ID number = 1).

VOLM

? ←

From PC to monitor.

30 001 ←

From monitor to PC.

Controlling the Monitor with a PC (RS-232C)

Response code format

When a command has been executed correctly

O K

Return code

(0DH, 0AH)

A response is returned after a command is executed.

* If an ID number has been assigned

O K SPC 0 0 1

ID number of respondin

monitor

Space (20

Return code

(0DH, 0AH)

When a command has not been executed

R R E

Return code

(0DH, 0AH)

* If an ID number has been assigned

R R E SPC 0 0 1

ID n

Space (20H)

Return code

(0DH, 0AH)

TIPS

• “ERR” is returned when there is no relevant command or

when the command cannot be used in the current state of

the monitor.

• If communication has not been established for reasons

such as a bad connection between the PC and monitor,

nothing is returned (not even ERR).

• If no monitor has been assigned the designated ID number

(e.g. if the command IDSL0002

is used, but no monitor

with ID number: 2 is found), no response is returned.

If execution of the command is taking some time

I W T A

Return code

(0DH, 0AH)

When the following commands are used, “WAIT” is returned.

In this case, a value will be returned if you wait a while. Do not

send any command during this period.

No ID number is attached to WAIT response.

• Commands which return WAIT:

1. When repeater control is used

2. When an IDSL or IDLK command is used

3. When one of the following commands is used: RSET,

INPS, ASNC, WIDE, EMAG, EPOS, PXSL, POWR,

AGIN, MWIN, MWIP, MWPP, ESTG, EMHV, EPHV,

ESHV

When control via RS-232C is locked (to prevent use)

using the operation lock function (see page 17)

E C D K O L

Return code

(0D

, 0A

)

When RS-232C/LAN SELECT is set to LAN

U N S E L E C T E D

Return code

(0D

H, 0AH)

Communication interval

• After OK or ERR is returned, you must send the following

commands.

To set a timeout for the command response, specify 10

seconds or longer.

When connecting multiple monitors in a daisy chain, set the

timeout to at least the product of the monitor’s position from

the computer multiplied by 10 seconds.

Example) 3rd monitor from computer: 30 seconds or longer.

• Provide an interval of 100 ms or more between the

command response and the transmission of the next

command.

LM0020

INPS0001

WAIT

Interval of 100 ms or more

TIPS

• When executing ALL RESET, set the timeout period to 30

seconds or longer.

• When turning the power on while the POWER ON DELAY

function is in use, set the timeout period to the POWER ON

DELAY period + 10 seconds or longer.

Advanced operation

This section explains commands for daisy chain connection.

The basic communication procedure is the same as in the

“One-to-one connection with a PC” section.

ID numbers

You can assign a unique ID number to each monitor (see

page 11). This allows you to control a particular monitor in a

daisy chain of monitors.

You can assign ID numbers either from the menu screen (using

the remote control) or from the PC using RS-232 cable.

xamp

]

ID number: 1 ID number: 2 ID number: 3 ID number:

If monitors are connected as shown above, you can

execute commands like “Set the volume of the monitor with

ID 4 to 20”.

When controlling monitors linked in a daisy chain by

designating ID numbers, you should basically avoid any

duplication of ID numbers.

ID numbers do not have to be assigned in ascending order

starting from the PC. They can also be connected as shown

below.

xamp

]

ID number: 3 ID number: 2 ID number: 4 ID number:

Controlling the Monitor with a PC (RS-232C)

Commands for ID control

The command examples shown on this page assume the

following connection and ID number set up.

ID number: 1 ID number: 2 ID number: 3 ID number: 4

IDST ......... A monitor receiving this command sets its own ID

number in the parameter eld.

Example:

IDST0001

001 ←

The ID number of this monitor is set to 1.

TIPS

You can automatically assign ID numbers by using the IDST

command with the Repeater control (see “Repeater control”

on page 21).

For example, using the command “IDST001+” automatically

sets the ID numbers, as shown below.

xamp

]

ID number: 1 ID number: 2 ID number: 3 ID number:

IDST001 + ←

ID setting command with repeater control

WAIT

001 ←

“OK” response from ID number: 1

OK 002 ←

“OK” response from ID number: 2

OK 003 ←

“OK” response from ID number: 3

OK 004 ←

“OK” response from ID number: 4 (End)

IDSL ........The parameter of this command sets the ID number

of the monitor. The monitor is subject to the next

command.

Example:

IDSL0002 ←

The next command is for the monitor

with ID number: 2.

WAIT ←

Searching for monitor with ID number:

OK 002 ←

Found monitor with ID number: 2

VOLM0030 ←

Sets volume of monitor with ID

number: 2 to 30.

WAIT ←

Processing

OK 002 ←

OK response from monitor with ID

number: 2

VOLM0020 ←

Sets volume to 20.

OK 001 ←

The volume of the monitor with ID

number: 1 (the one directly connected

to the PC) is set to 20.*

* The IDSL command is effective only once, for the

immediately succeeding command.

IDLK ........

The parameter of this command sets the ID

number of the monitor. The monitor is subject to all

subsequent commands.

Example:

IDLK0002 ←

Following commands are for the monitor

with ID number: 2.

WAIT ←

Searching for monitor with ID number:

OK 002 ←

Found monitor with ID number: 2

VOLM0030 ←

Sets volume of monitor with ID

number: 2 to 30.*

WAIT ←

Processing

OK 002

VOLM0020 ←

Sets volume of monitor with ID

number: 2 to 20.*

WAIT

002

IDLK0000 ←

Canceling xed ID number setting

WAIT ←

Canceling IDLK

OK 002 ←

Cancelation complete

VOLM0010

001 ←

The volume of the monitor with ID number:

1 (the one directly connected to the PC) is

set to 10. (IDLK is canceled.)

* The IDLK command remains effective until it is

canceled, or power is shut off.

IDCK ........Provides screen display of the ID number currently

assigned to a monitor, and the ID number currently

set for IDLK (if any).

Example:

(After executing IDLK0002)

IDCK0000

←

(Parameter has no meaning.)

ID : 001 IDLK : 002

←

Returned response. The ID

number is also displayed on the

monitor screen.

IDCK000 +

←

Repeater control. (If a command

is used with repeater control, ID

designation using IDSL or IDLK

is canceled.)

WAIT

ID : 001 IDLK : 000

ID : 002 IDLK : 000

ID : 003 IDLK : 000

ID : 004 IDLK : 000

Page is loading ...

Sharp PN-E471R Specification

Brand: Sharp

Model: PN-E471R

Category: LED displays

Type: Specification

This manual is also suitable for

PNE471R

Download PDF

report

Sharp PN-E471R Specification

This manual is also suitable for

Sharp PN-E471R Specification

Related papers

Other documents