Definitive Technology IW Sub 10/10 User manual

Brand: Definitive Technology

Model: IW Sub 10/10

Category: Soundbar speakers

Type: User manual

GET READY TO ROCK YOUR HOUSE!

Congratulations on your purchase of the remarkable

Deﬁnitive Technology in-wall subwoofer IWSub

Reference and its matching Deﬁnitive Technology

SubAmp 600. This extraordinary In-Wall Subwoofer

incorporates Deﬁnitive Technology’s exclusive and effec-

tive SuperCube

™

technology for spectacular bass perfor-

mance, the kind of musically accurate low end that’s

never before been available in a compact, nearly invisible

in-wall subwoofer. The IWSub Reference is speciﬁcally

designed to be powered by the matching Deﬁnitive

Technology SubAmp 600, which features two discrete

high power ampliﬁers to provide optimal power when

driving one or two IWSubs in your installation, whether

it is for whole-house distributed audio or dedicated music

or home theater applications.

IWSub Reference

™

& SubAmp 600

Ultra High-Performance In-Wall Subwoofer

and Separate Ampliﬁer Module

Owner’s Manual

CAUTION! To reduce the risk of electric shock and ﬁre, do not remove the cover or back

plate of this device. There are no user serviceable parts inside. Please refer all servicing to

licensed service technicians. Avis: Risque de choc electricque, ne pas ouvrir.

CAUTION! The international symbol of a lightning bolt inside a triangle is intended to alert

the user to uninsulated “dangerous voltage” within the device’s enclosure. The international

symbol of an exclamation point inside a triangle is intended to alert the user to the presence

of important operating, maintenance and servicing information in the manual accompanying

the device.

CAUTION! To prevent electrical shock, match wide blade of plug to wide slot, fully insert.

Attention: Pour eviter les chocs electriques, introduire la lame la plus large de la ﬁche dans

la borne correspondante de la prise et pousser jusqu'au fond.

CAUTION! To reduce the risk of electrical shock, do not expose this equipment to rain

or moisture.

1. Read Instructions—All safety and operating instructions should be read before operating the device.

2. Retain Instructions—The safety and operating instructions should be retained for future reference.

3. Heed Warnings—All warnings on the device and in the operating instructions should be adhered to.

4. Follow Instructions—All operating and safety instructions should be followed.

5. Water & Moisture—The device should never be used in, on or near water for risk of fatal shock.

6. Carts & Stands—The device should only be used on carts or stands recommended by the manufacturer.

7. Wall & Ceiling Mounting—The device should be mounted on a wall or ceiling only as recommended

by the manufacturer.

8. Ventilation—The device should always be located in such a way that it maintains proper ventilation. It

should never be placed in a built-in installation or anywhere that may impede the ﬂow of air through its

heat sink.

9. Heat—Never locate the device near heat sources such as radiators, ﬂoor registers, stoves or other

heat-generating devices.

10. Power Supply—The device should only be connected to a power supply of the type described in the

operating instructions or as marked on the device.

11. Power Cord Protection—Power cables should be routed so they are not likely to be stepped on or

crushed by items placed on them or against them. Special attention should be paid to areas where the

plug enters a socket or fused strip and where the cord exits the device.

12. Cleaning—The device should be cleaned in accordance with manufacturer’s instructions.

13. Periods Of Non-Use—The device should be unplugged when not being used for extended periods.

14. Dangerous Entry—Care should be taken that no foreign objects or liquids fall or are spilled inside

the device.

15. Damage Requiring Service—The device should be serviced by licensed technicians when:

• The plug or power supply cord has been damaged.

• Objects have fallen or liquid spilled inside of the device.

• The device has been exposed to moisture.

• The device does not appear to be operating properly or exhibits a marked change in performance.

• The device has been dropped or the cabinet becomes damaged.

16. Service—The device should always be serviced by licensed technicians. Only replacement parts

speciﬁed by the manufacturer should be used. The use of unauthorized substitutions may result in

ﬁre, shock, or other hazards.

Safety Precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Unpacking Your IWSub Reference

and SubAmp 600

• Please inspect your new equipment carefully. Notify your Deﬁnitive

Technology dealer immediately if you notice any damage or missing items.

• Record the serial numbers of your new equipment (usually found on the

rear panels). Note this information in the appropriate place on your Warranty

Card. Mail in your Warranty Card within 10 days of purchase.

• Keep the cartons and packing material. They will do the best job of

protecting your speakers if they need to be transported.

Important Note Concerning In-Wall Installation

The IWSub Reference is designed to be installed inside the walls of your home

quickly and easily. Because of its superb sonic performance, its installation

location within your room is very ﬂexible. But your room is not like anyone

else’s room, and because of its unique size and shape will have its own require-

ments for optimal sonic performance. We recommend that you consult with the

Custom Installation Specialist at your Deﬁnitive Technology dealer regarding

your special needs or if you are at all uncertain about the best and safest way

to install your subwoofer.

• Before starting construction or modiﬁcation of your walls or ceilings, you

should familiarize yourself with any applicable local ﬁre and building codes.

• Speaker wire must be run inside your wall as part of the installation process

of in-wall loudspeakers. Plan the connection before you start your loud-

speaker installation.

• Make sure the locations you select do not conceal studs, electrical wiring or

plumbing. Prior to installation, hold the speaker in your chosen location to

make sure it safely clears obstacles such as studs, corners, beams, lighting

ﬁxtures and door/window frames. Your cutout must be at least 1" (25mm)

from adjoining walls or ceiling, internal studs or plumbing, and a minimum

of 5" above the ﬂoor or 1" above the top of the baseboard (whichever is

higher). Note that the frame around the inset loudspeaker extends 1" beyond

your cutout.

• It is highly recommended that you take advantage of the expertise

of a professional installation specialist.

Important Note Concerning Your

IWSub Reference and SubAmp 600

Your IWSub Reference is speciﬁcally designed to be used in conjunction with

the Deﬁnitive Technology SubAmp 600 and should never be used with another

ampliﬁer. You will not achieve optimal performance, and you may cause dam-

age to your IWSub Reference if you attempt to power it using another ampliﬁer

or receiver. BECAUSE OF THIS, THE IWSUB Reference WARRANTY IS

VOIDED IF AN AMPLIFIER OR RECEIVER OTHER THAN THE DEFINI-

TIVE TECHNOLOGY SUBAMP 600 IS USED TO DRIVE THIS SUB-

WOOFER.

Installation

Mounting Your SubAmp 600 In An Audio Rack

Your SubAmp 600 features side mounting brackets for use in professional audio

racks. When installing the SubAmp 600 in either professional audio racks or

in AV rack furniture, be sure to leave adequate ventilation space around the

SubAmp 600 unit.

Tools Required for IWSub Reference In-Wall

Installation

• Pencil for marking the location of installation.

• Keyhole saw or utility knife for cutting drywall.

• Level.

• Screwdriver, preferably powered, with Phillips head bit.

• Power drill with appropriate bit (optional, for starting wall cut).

• Template (included: 14

/8" x 19

/8").

• Gasket material (included).

The IWSub Reference is designed to be located between two vertical studs,

inside a space of 14

/2"–15

/2", with the long dimension of the speaker

oriented vertically. If your studs are spaced wider than this, you will have to

shim one side of the inner wall space to properly secure the speaker in a

/2"–15

/2" space.

Mounting Bracket Mounting Bracket

2. Make certain to incorporate at least 1

/4" of space above and below the area

within the inner wall space to make room for the IWSub’s locking arms.

3. With these measurement requirements in mind, place the template against

the inside edge of one of the studs. (Do not “center” the template if your

studs are wider than 14

/2"–15

/2".) Use a level to make certain the

template is straight and plumb. The outside edge of the template will

be your exact cutout size. [Figure 1]

Carefully cut the hole with the appropriate cutting tool for your wall mater-

ial. Start the hole by drilling a hole on the inside of the template line (with

the drill bit touching the line). Use this hole to insert your saw or knife

and begin cutting. [Figur

e 2]

5. Before installing the speaker in the hole, apply the four long strips of

gasket material to the speaker: two pieces on each side of the speaker that

will come into contact with the studs. [Figure 3] Use the three shorter strips

of gasket material to pad the rear of the speaker against the back of the

exposed wall. [Figure 4]

Figure 3 Figure 4

Figure 2

Figure 1

6. Once you have cut the hole, ﬁsh your previously positioned wiring out

of the hole and connect your speaker. See the next section for detailed

hookup instructions. Make certain that you connect the wire from the

red terminal (+) of your SubAmp 600 to the red terminal (+) on your

speaker and the wire from the black terminal (-) of your SubAmp 600

to the black terminal (-) on your speaker. Be sure to maintain channel

consistency (use either channel one or channel two).

7. Place the subwoofer carefully into the hole [Figure 5]. Secure the sub

enclosure using the 6 screws provided. These screws go into the holes

in the front of the enclosure and angle back into the studs (or

, if the space

between your studs was wider than 14

/2"–15

/2", into the shims). [Figure

6] Tighten all the screws on one side before installing and tightening the

screws on the other side.

8. Secure the locking arms at the top and bottom of the plastic frame

by turning the screws clockwise, taking care not to over tighten.

Making System Connections With Your

SubAmp 600

Recommended Hookup Method One

1. Use a Low (Line) Level RCA connection from your receiver’s LFE Out in

to the LFE Input of the SubAmp 600.

2. Use Speaker Wire to connect the top set of Sub Out Jacks on the SubAmp

600 to the terminals on the IWSub Reference.

3. The SubAmp 600 features an Adjustable Crossover setting on its

front panel. This hookup bypasses the SubAmp 600’s Adjustable

Crossover feature.

Figure 6

Figure 5

Hookup Method Two

RCA from Receiver

To Subwoofer

Hookup Method One

RCA from Receiver

To Subwoofer

Hookup Method Two

1. Use a Low (Line) Level RCA connection from your receiver’s L and R

Line Level Outputs in to the L and R Input of the SubAmp 600. This

connection is “summed” within the SubAmp 600.

2. Use Speaker Wire to connect the top set of Sub Out Jacks on the SubAmp

600 to the terminals on the IWSub Reference.

3. The SubAmp 600 features an Adjustable Crossover setting on its front

panel. This setting will work with this connection, giving you extra control

over your subwoofer settings.

Hookup Method Three—High Level Speakerwire

Connection

When using the IWSub Reference for stereo applications, you can feed it either

Low Level signals as described in Hook Up Methods One and Two, or use

Hookup Method Three described here.

1. Connect Speaker Wire from your receiver’s Left and Right outputs to the

Speaker Level Inputs on the SubAmp 600.

2. Use Speaker Wire to connect the Speaker Level Outputs of the SubAmp

600 to your loudspeakers.

3. Use Speaker Wire to connect the top set of Sub Out Jacks on the SubAmp

600 to the terminals on the IWSub Reference.

Hookup Method Three

To Subwoofer

From Receiver

To Speakers

4. The SubAmp 600 features an Adjustable Crossover setting on its front

panel. This setting will work with this connection, giving you extra control

over your subwoofer settings.

Making Adjustments to Your SubAmp 600

The rear panel of your SubAmp 600 features a Remote Mini Plug Input and

Auto/Remote Slider Switch.

• Use this feature to connect your SubAmp 600 to the Remote Out of your

receiver. Moving the Slider Switch to “Remote” will enable your SubAmp

600 to then switch on when you power up your other equipment.

• If a remote connection is not used, this slider MUST be switched to “Auto”

in order for the SubAmp 600 to operate properly.

The front panel of your SubAmp 600 features Volume, Crossover and Phase

Adjustment controls.

Volume Adjustment

Use this setting to control the level (volume) of bass response. Begin with

the volume set at about the 11 o’clock position, and, once you have made all

your other settings, modify this setting for optimum volume and low distortion.

Remember: damage can occur to loudspeakers when an ampliﬁer, regardless of

its wattage, is made to play at higher listening levels than its power can clearly

produce. This is usually beyond the “noon or 1 o’clock” position on the volume

control. If you hear distortion, TURN IT DOWN.

Crossover Adjustment

This control adjusts the frequency range over which your subwoofer operates. In

most situations, the middle range (11 – 2 o’clock) of this control will sound best.

Experiment and let your ears be the ﬁnal judge. Turning the setting higher will

tend to add more “warmth” to the bass and lower midrange, possibly at the sacri-

ﬁce of bass “tightness” and midrange clarity. Turning the setting down from the

recommended setting will make the bass and lower midrange sound “leaner.”

Phase Adjustment

Adjusting the Phase can be a little tricky. If you're in doubt, just leave the Phase

at 0 (zero). The best way to adjust the Phase is to get a friend to help you out.

Play music that features a good combination of bass notes and deep male vocals

at different frequencies. Have one person sit in the normal listening position

while the other person slowly rotates the Phase control until it reaches the posi-

tion that produces the fullest bass sound across the bass spectrum.

Installing More Than One IWSub In Your Room,

Or One Each in Each of Two Rooms

Installing two IWSub References into the walls of your room, or one each in

each of two rooms, will allow you to achieve a mind-blowing amount of bass

from subwoofers that take up no ﬂoor space! The SubAmp 600 has two separate

high power ampliﬁers for just this purpose. It is designed to drive one or two

IWSub References with full performance and maximum power delivered to each

subwoofer.

1. Connect inputs to the sub as described in Hookup Methods One, Two

or Three.

2. Use Speaker Wire to connect the top set of Sub Out Jacks on the SubAmp

600 to the terminals on one IWSub Reference.

3. Use Speaker Wire to connect the bottom set of Sub Out Jacks on

the SubAmp 600 to the terminals on the other IWSub Reference.

Multi-Sub Hookup

Sub 2

RCA from Receiver

Sub 1

Painting Your IWSub Reference

The IWSub Reference is easy to paint. It virtually disappears into your room

when it is the same color as your wall. For best results, paint the grille and frame

separately prior to in-wall installation.

You Will Need:

• Paint of your choice (to make the job easier, we recommend spray painting

the grille).

• A paperclip (for removing the paintable grille).

• Masking tape.

• Paint mask (to cover unpaintable parts, supplied).

Preparing to Paint:

1. Separate the parts of the speaker. The grille can be removed simply by

carefully hooking it with a bent paperclip and pulling it gently away from

the frame. [Figure 7]

When painting the frame of the speaker

, use the supplied paint mask to

carefully mask off the front of the speakers to protect the drivers and bafﬂes

while painting [Figure 8]. You can do this while the speaker is already

installed in the wall (if, for instance, you’re repainting the room). If you do

not have the paint masks, carefully mask the speaker components using

paper and masking tape.

Painting the Frame:

1. Apply paint to exposed (unmasked) parts. Use two or more thin coats.

Spray painting is recommended.

2. When the paint is completely dry, remove the masking material.

Figure 8

Figure 7

Painting the Grille:

1. The grille of the IWSub Reference features an even, protective powder

coating. This powder coating is an ideal primer.

2. Grilles must be spray painted. Do not use a brush and paint. Thick, brushed

paint may clog the grille holes and impair performance.

3. After removing the grille by care-

fully hooking it with a bent paper

clip and pulling it gently away

from the frame, spray on two thin

coats of ﬁnish color. [Figure 9]

If you’re using a compressor and

spray gun, use the ﬁnest, most dif-

fuse setting. Be careful not to ﬁll

the holes in the grille with paint.

When paint is completely dry

carefully reinstall the grille.

Troubleshooting Your IWSub

• If, after following these hookup and installation directions, you

experience difﬁculty, please double-check all wire connections.

• Check the setting of the “Auto/Remote” slider switch on the rear panel of

the SubAmp 600. If no remote connection is made, this switch MUST be

set to “Auto” in order for the SubAmp 600 to operate properly.

• Many ampliﬁers and receivers have sophisticated internal protection

circuitry. If for some reason your protection circuitry is tripped, turn

down your system’s volume level and wait ﬁve minutes before restarting

the system.

• If you are still having problems, please contact your authorized Deﬁnitive

Technology dealer for assistance.

Figure 9

Service

Service and warranty work on your Deﬁnitive Technology audio equipment will

be performed by your authorized Deﬁnitive Technology dealer. If, however, you

wish to return your equipment directly to us, please contact us ﬁrst to describe

the problem you may be having and to allow us to give you return authorization

or suggest the location of the nearest factory service center. The address below is

the address of the Deﬁnitive Technology ofﬁce only. UNDER NO CIRCUM-

STANCES SHOULD EQUIPMENT BE SHIPPED TO OUR OFFICE OR

RETURNED WITHOUT CONTACTING DEFINITIVE TECHNOLOGY

FIRST TO OBTAIN RETURN AUTHORIZATION.

Deﬁnitive Technology

1433 Cr

onridge Drive

Suite K

Owings Mills, Maryland, USA 21117

410-363-7148

Email Deﬁnitive Technology at info@deﬁnitivetech.com.

isit us at www

.deﬁnitivetech.com for more information and to

see the whole exciting line of Deﬁnitive Techno

logy products.

Visit us at www.deﬁnitivetech.com

and learn about all our exciting products.

IWSub Reference

Outer Dimensions: 15

" W x 26

" H

Cut-out Size: 14

" W x 25

" H

Rec. Assoc. Amp: SubAmp 600

Frequency Response: 14 Hz – 200 Hz

Nominal Impedance: 4 ohms

Driver Complement:

One

13" long-excursion woofer

coupled to a 13" infrasonic radiator

Enclosure: Non-resonant sealed medite

enclosure

Net Weight: 26 lbs.

SubAmp 600

One Channel Operation: 275 Watts

Two Channels Driven: 230 Watts each

With Brackets, Feet removed: 3

" H x 19

" W x 9

" D

Without Brackets, including Feet: 3

" H x 17

" W x 9

" D

When installing the SubAmp 600 in either professional audio racks or in

AVrack furniture, be sure to leave adequate ventilation space around the

SubAmp 600 unit. Ideally, we recommend leaving a single rack unit open

above and below the product.

IWSub Reference & SubAmp 600 Speciﬁcations

This product complies with the essential requirements of

EMC directives 89/336/EEC and 73/23/EEC (inclusive of

93/68/EEC) and carries the CE mark accordingly.

CXAT012809

Deﬁnitive Technology warrants to the original retail purchaser only that this Deﬁnitive

Technology Loudspeaker Product (the “Product”) will be free from defects in materials and

workmanship for a period of ﬁve (5) years covering the drivers and cabinets, and three (3) years

for the electronic components from the date of the original purchase from a Deﬁnitive

Technology Authorized Dealer. However, this warranty will automatically terminate prior to

the expiration of ﬁve (5) years for the drivers and cabinets and three (3) years for the electronic

components if the original retail purchaser sells or otherwise transfers the Product to any other

party. The original retail purchaser shall hereinafter be referred to as “you.” Defective Products

must be shipped, together with proof of date of purchase, prepaid insured to the Authorized

Dealer from whom you purchased the Product, or to the nearest factory service center.

Product(s) must be shipped in the original shipping container or its equivalent; in any case the

risk of loss or damage in transit is to be borne by you. If, upon examination at the Factory or a

Deﬁnitive Technology Authorized Dealer, it is determined that the unit was defective in

materials or workmanship at any time during this Warranty period, Deﬁnitive Technology or

the Deﬁnitive Technology Authorized Dealer will, at its option, repair or replace this Product at

no additional charge, except as set forth below. All replaced parts and Product(s) become the

property of Deﬁnitive Technology. Product(s) replaced or repaired under this Warranty will be

returned to you, within a reasonable time, freight collect.

This Warranty does not include service or parts to repair damage caused by accident, mis-

use, abuse, negligence, inadequate packing or shipping procedures, commercial use, voltage in

excess of the rated maximum of the unit, cosmetic appearance of cabinetry not directly

attributable to defects in materials or workmanship, or service, or repair or modiﬁcation of the

Product which has not been authorized by Deﬁnitive Technology. Deﬁnitive Technology makes

no Warranty with respect to its Products purchased from dealers or outlets other than

Deﬁnitive Technology Authorized Dealers. This Warranty is in lieu of all other expressed

Warranties. If this Product is defective in material or workmanship as warranted above, your

sole remedy shall be repair or replacement as provided above. In no event will Deﬁnitive

Technology be liable to you for any incidental or consequential damages arising out of the use

or inability to use the Product, even if Deﬁnitive Technology or a Deﬁnitive Technology

Authorized Dealer has been advised of the possibility of such damages, or for any claim by any

other party. Some states do not allow the exclusion or limitation of consequential damages, so

the above limitation may not apply to you.

All implied warranties on the Product are limited to the duration of this expressed

Warranty. Some states do not allow limitation on how long an implied Warranty lasts, so the

above limitations may not apply to you. This Warranty gives you speciﬁc legal rights, and you

also may have other rights which vary from state to state.

Limited Warranty:

5-Years for Drivers and Cabinets,

3-Years for Electronic Components

Definitive Technology IW Sub 10/10 User manual

Brand: Definitive Technology

Model: IW Sub 10/10

Category: Soundbar speakers

Type: User manual

Download PDF

report

Definitive Technology IW Sub 10/10 User manual

Definitive Technology IW Sub 10/10 User manual

Related papers

Other documents