Friedrich SH14J30B-A Owner's manual

Friedrich
Brand
Friedrich
Model
SH14J30B-A
Category
Split-system air conditioners
Type
Owner's manual

This manual is also suitable for

HG2003(1-03)
2004
Service & Parts Manual
HazardGard
®
Room Air Conditioner
MODELS
SH14J30B-A
SH20J30B-A
2
TABLE OF CONTENTS
Specifications ................................................................................................................................... 3
Performance Data............................................................................................................................ 3
Component Operation & Testing ...................................................................................................... 4
Compressors ................................................................................................................................... 4
Thermal Overload ............................................................................................................................ 4
Checking Compressor Efficiency..................................................................................................... 5
Fan Motor ......................................................................................................................................... 5
Solid State Relay .............................................................................................................................. 5
System Control Switch..................................................................................................................... 6
Run Capacitor .................................................................................................................................. 6
Thermostat....................................................................................................................................... 6
Low Ambient Bypass Valve .............................................................................................................. 8
Sealed Refrigeration System Repairs .............................................................................................. 8
Hermetic Component Replacement................................................................................................. 9
Special Procedure in the case of Compressor Motor Burn-Out....................................................... 9
Rotary Compressor Special Troubleshooting & Service ................................................................ 10
Refrigerant Charge......................................................................................................................... 10
Troubleshooting ......................................................................................................................... 11-13
Wiring Diagram .............................................................................................................................. 14
Cabinet Parts Diagram.................................................................................................................. 15
Chassis Parts Diagram................................................................................................................. 16
Parts List ................................................................................................................................... 17-19
PAGE
3
* Rating Conditions: 80° F. Room Air Temperature and 59% Relative Humidity with 95° F. Outside Air Temperature at 40% Relative Humidity.
PERFORMANCE EVAPORATOR AIR OPERATING ELECTRICAL R-22 COMP.
DATA * TEMP° F PRESSURES RATINGS REFRIG. OIL
DISCHARGE TEMP SUCTION DISCHARGE AMPS LOCKED CHARGE IN CHARGE IN
AIR DROP °F ROTOR AMPS OUNCES FLUID OZ.
56.78 23.22 79 296 7.8 43 28 32
8.5
52.83 27.16 79.5 282 9.8 52 39 32
10.4
SH14J30B-A
SH14J30B-A
SH20J30B-A
SH20J30B-A
BTUH 14000/14000 19000/18800
E.E.R. - Btu/watt 8.0/8.0 8.5/8.5
Volts 230/208 230/208
Hertz/Phase 60/1 60/1
Amperes 7.8/8.5 9.9/10.8
Total Watts 1750/1750 2235/2210
Fuse/Breaker Size 15 20
Fan RPM 1095 1095
Evaporator Air CFM 375 425
Dehumidification-Pts./hr. 4.0 5.7
Width 25-15/16” 25-15/16”
Height 15-15/16” 17-15/16”
Depth 27-3/8” 27-3/8”
Min. Ext. into Room 5-7/8” 5-7/8”
Min. Ext to Outside 16-15/16” 16-15/16”
Net Weight 129 Lbs. 177 Lbs.
Shipping Weight 147 Lbs. 199 Lbs.
Maximum Temperature Rating 120
0
C (248
0
F) Ignition Temperature Rating
for Class 1, Division 2, Group D
SPECIFICATIONS
SH14J30B-A SH20J30B-A
4
COMPRESSOR WINDING TEST (Figure 2.)
Remove the compressor terminal box cover and
disconnect the wires from the terminals. Using an
ohmmeter, check continuity across the following:
DISCONNECT ELECTRICAL POWER TO
THE UNIT BEFORE SERVICING OR
TESTING
COMPONENT OPERATION AND TESTING
WARNING
COMPRESSORS
Compressors are single phase, 208/230 volt. All
compressor motors are permanent split capacitor
type, using only a running capacitor across the start
and run terminal.
All compressors are internally spring mounted and
externally mounted on rubber isolators.
Line Voltage Overload
The compressor is equipped with an internal line
voltage overload. This overload is embedded in
the windings of the motor to sense the motor
temperature. The overload will open and
disconnect the power to the motor due to high
temperatures caused by:
1. A locked rotor.
2. Excessive running amps.
3. High discharge temperature.
4. Low refrigerant charge.
FIGURE 1 INTERNAL OVERLOAD
LINE BREAK
INTERNAL OVERLOAD
OHMMETER
FIGURE 2 COMPRESSOR WINDING TEST
Testing Procedures
1. Terminal "C" and "S" - no continuity -
open winding - replace compressor.
2. Terminal "C" and "R" - no continuity -
open winding - replace compressor.
3. Terminal "R" and "S" - no continuity
open winding - replace compressor.
4. Terminal "C" and the shell of the
compressor – continuity – grounded
motor – replace compressor.
5. Should continuity exist between
terminals "R" and "S", but not between
terminals "C" and "S" and "C" and "R",
the internal overload may be open. If
the compressor is extremely hot, allow
it sufficient time to cool. It may require
as long as one hour for the compressor
to cool sufficiently for the internal
overload to close.
5
FAN MOTOR (Figure 4)
A 230 volt single phase permanent split capacitor
motor is used to drive the evaporator blower and
condenser fan. A running capacitor is wired across
the start and run terminals of the motor.
The motor is totally enclosed and is protected with
a line voltage overload located internally of the
motor. The motor shaft is stainless steel to resist
corrosion.
CHECKING COMPRESSOR EFFICIENCY
The reason for compressor inefficiency is
normally due to broken or damaged suction and/
or discharge valves, reducing the ability of the
compressor to pump refrigerant gas.
This condition can be checked as
follows:
1. Install a piercing valve on the suction and
discharge or liquid process tube.
2. Attach gages to the high and low sides of the
system.
3. Start the system and run a "cooling or
heating performance test."
If test shows:
A. Below normal high side pressure.
B. Above normal low side pressure.
C. Low temperature difference across the coil.
The compressor valves are faulty -
replace the compressor.
GROUND TEST
Use an ohmmeter set on its highest scale. Touch
one lead to the compressor body (clean point of
contact, as a good connection is a must) and the
other probe in turn to each compressor terminal.
(See Figure 3.) If a reading is obtained, the
compressor is grounded and must be replaced.
FIGURE 3 TYPICAL GROUND TEST
FAN MOTOR – TEST
Disconnect power to the unit.
1. Determine that the capacitor is serviceable.
2. Disconnect the black lead from the circuit
board.
3. Apply "live" test cord leads to the common
terminal of the capacitor and the black lead.
The motor should run at high speed.
SOLID STATE RELAY (Figure 5)
Two 50 amp rated 208/230 volt solid state relays
are used to energize the compressor and fan motor.
Terminals 3 and 4 are the 208/230 volt line side.
Terminals 1 and 2 are load side contacts.
FIGURE 4 FAN MOTOR
FIGURE 5 SOLID STATE RELAY
LED indicates
contacts closed
when lit
Line side
Load side
6
RED DOT
RUN CAPACITOR
FAN
MOTOR
COMPRESSOR
FIGURE 7 RUN CAPACITOR HOOK–UP
CAPACITOR, RUN
A run capacitor is wired across the auxiliary and
main winding of a single phase permanent split
capacitor motor such as the compressor and fan
motors. A single capacitor can be used for each
motor or a dual rated capacitor can be used for
both.
The capacitor’s primary function is to reduce the
line current while greatly improving the torque
characteristics of a motor. The capacitor also
reduces the line current to the motor by improving
the power factor of the load. The line side of the
capacitor is marked with a red dot and is wired to
the line side of the circuit (see Figure 7.)
THERMOSTAT
A cross ambient
thermostat is used
to maintain the
desired comfort level.
The thermostat reacts only
to a change in temperature
at the bulb location.
Important to the
successful operation
of the unit is the position
of the sensing bulb in
relation to the evaporator
(see Figure 8).
FIGURE 8
SENSING BULB
LOCATION
CAPACITOR – TEST
1. Remove the capacitor from the unit.
2. Check for visual damage such as bulges,
cracks, or leaks.
3. For dual rated capacitors, apply an ohmmeter
lead to the common (C) terminal and the other
probe to the compressor (HERM) terminal. A
satisfactory capacitor will cause a deflection
on the pointer, then gradually move back to
infinity.
4. Reverse the leads of the probe and
momentarily touch the capacitor terminals. The
deflection of the pointer should be two times
that of the first check if the capacitor is good.
5. Repeat steps 3 and 4 to check the fan motor
capacitor.
NOTE: A shorted capacitor will indicate a low
resistance and the pointer will move more to the
“0” end of the scale and remain there as long as
the probes are connected. An open capacitor
will show no movement of the pointer when
placed across the terminals of the capacitor.
SYSTEM CONTROL SWITCH (Figure 6)
This switch is double pole, single throw. Check for
continuity between terminals 2 and 3, and 5 and 6.
FIGURE 6 SWITCH, ON-OFF
RANGE:
Thermostat
(Part No. 618-225-02)
60° F ( ± 2° ) to 90° F( ± 4° )
7
Note: The temperature must be within the
range listed to check the thermostat. Refer to
the troubleshooting section in this manual for
additional information on thermostat testing.
TEST
Remove the wires from the thermostat. Turn the
thermostat to its coldest position. Check to see if
there is continuity between the two terminals. Turn
the thermostat to its warmest position. Check
continuity to see if the thermostat contacts open.
8
LOW AMBIENT BYPASS VALVE (Figure 9)
The HazardGard unit is designed to operate at low
outside ambient temperatures. This is
accomplished by the use of a bypass valve installed
in the refrigeration circuit. The valve is connected
between the discharge line at the compressor and
the suction process tube. The valve responds to
suction pressure which, when reduced in the
system, causes the valve to open and bypass hot
gas from the high pressure side to the low pressure
side of the system. The hot gas entering the
compressor mixes with the cool gas returned
through the suction line, thus increasing the suction
pressure. The valve is preset to open when the
suction pressure reaches 50 psig. This pressure
setting cannot be altered. The system can be
operated at outdoor temperatures as low as 45°
F
before the evaporator coil will begin to accumulate
frost.
To determine if the valve operates, block the return
air to the evaporator coil. Turn on the unit and touch
the tube at the bypass valve outlet which connects
to the suction process tube. When the low side
pressure reaches approximately 50 psig, the valve
will begin to open and the tube will get hot. This
method will determine if the valve is responding to
the suction pressure change.
FIGURE 9
LOW AMBIENT Bypass
VALVE
EQUIPMENT REQUIRED:
1. Voltmeter
2. Ammeter
3. Ohmmeter
4. E.P.A Approved Refrigerant Recovery System
5. Vacuum Pump (capable of 200 microns or less
vacuum).
6. Acetylene Welder
7. Electronic Halogen Leak Detector G.E. Type
H-6 or equivalent).
8. Accurate refrigerant charge measuring device
such as:
a. Balance Scales - 1/2 oz. accuracy
b. Charging Board - 1/2 oz. accuracy
9. High Pressure Gauge - (0-400 lbs.)
10. Low Pressure Gauge - (30" - 150 lbs.)
11. Vacuum Gauge - (0-1000 microns)
EQUIPMENT MUST BE CAPABLE OF:
1. Recovering CFC’s as low as 5%.
2. Evacuation from both the high side and low side
of the system simultaneously.
3. Introducing refrigerant charge into the high side
of the system.
4. Accurately weighing the refrigerant charge
actually introduced into the system.
5. Facilities for flowing nitrogen through the
refrigeration tubing during all brazing
processes.
SEALED REFRIGERATION SYSTEM REPAIRS
9
NOTE: This procedure can be speeded up by
the use of heat lamps, or by breaking the
vacuum with refrigerant or dry nitrogen at 5,000
microns. Pressure system to 5 PSIG and leave
in the system a minimum of 10 minutes.
Recover refrigerant, and proceed with
evacuation to a pressure of 200 microns or a
minimum of 10%.
11. Break the vacuum by charging the system from
the high side with the correct amount of
refrigerant specified. This will prevent boiling
the oil out of the crankcase.
NOTE: If the entire charge will not enter the high
side, allow the remainder to enter the low side in
small increments while operating the unit.
12.Restart the unit several times after allowing
pressures to stabilize. Pinch off the process
tubes, cut and solder the ends. Remove the
pinch off tool, and leak check the process tube
ends.
SPECIAL PROCEDURES IN THE CASE OF
COMPRESSOR MOTOR BURNOUT
1. Recover all refrigerant and oil from the system.
2. Remove the compressor, capillary tube and
filter drier from the system.
3. Flush the evaporator, condenser and all
connecting tubing with dry nitrogen, or
equivalent, to remove all contamination from the
system. Inspect the suction and discharge lines
for carbon deposits. Remove and clean if
necessary.
4. Reassemble the system, including a new drier-
strainer and capillary tube.
5. Proceed with processing as outlined under
hermetic component replacement.
HERMETIC COMPONENT REPLACEMENT
The following procedure applies when replacing
components in the sealed refrigeration circuit or
repairing refrigerant leaks. (Compressor,
condenser, evaporator, capillary tube, refrigerant
leaks, etc.)
1. Recover the refrigerant from the system at the
process tube located on the high side of the
system by installing a line tap on the process
tube. Apply the gauge from the process tube to
EPA approved gauges from the process tube
to the EPA approved recovery system. Recover
the CFC’s in the system to at least 5%.
2. Cut the process tube below the pinch off in the
suction side of the compressor.
3. Connect the line from the nitrogen tank to the
suction process tube.
4. Drift dry nitrogen through the system and
unsolder the more distant connection first. (Filter
drier, high side process tube, etc.)
5. Replace the inoperative component, and always
install a new filter drier. Drift dry nitrogen through
the system when making these connections.
6. Pressurize the system to 30 PSIG with proper
refrigerant and boost the refrigerant pressure
to 150 PSIG with dry nitrogen.
7. Leak test the complete system with the electric
halogen leak detector, correcting any leaks
found.
8. Reduce the system to zero gauge pressure.
9. Connect the vacuum pump to the high side and
low side of the system with deep vacuum hoses,
or copper tubing. (Do not use regular hoses.)
10.Evacuate the system to an absolute holding
pressure of 200 microns or less.
10
NOTE:
All inoperative compressors returned to
Friedrich must have all lines properly plugged
with the plugs from the replacement
compressor.
REFRIGERANT CHARGE
1. The refrigerant charge is extremely critical.
Measure the charge carefully and as exactly as
possible to the nameplate charge.
2. The correct method for charging the rotary is to
introduce liquid refrigerant into the high side of
the system with the unit off. Then start the
compressor and enter the balance of the
charge, gas only, into the low side.
The introduction of liquid into the low side,
without the use of a capillary tube, will cause
damage to the discharge valve of the rotary
compressor.
ROTARY COMPRESSOR SPECIAL
TROUBLESHOOTING AND SERVICE
Basically, troubleshooting and servicing rotary
compressors is the same as on the reciprocating
compressor with only a few exceptions.
1. Because of the spinning motion of the rotary,
the mounts are critical. If vibration is present,
check the mounts carefully.
2. The electrical terminals on the rotary are in a
different order than the reciprocating
compressors. The terminal markings are on the
cover gasket. Use your wiring diagram to insure
the correct connections.
11
PROBLEM POSSIBLE CAUSE TO CORRECT
Unit does not
run.
PROBLEM POSSIBLE CAUSE TO CORRECT
Dirty Filter.
Restricted air flow.
Inoperative thermostat.
Short of refrigerant.
Partially restricted capillary.
Inoperative fan motor.
Evaporator
coil freezes
up.
PROBLEM POSSIBLE CAUSE TO CORRECT
Test cooling performance of unit. Unit undersized.
Check for partially iced coil. Check temperature split across
coil.
Check for presence of oil on silver soldered connections.
Check for partially iced coil. Check split across coil. Check
for low running amperage.
Check operation of thermostat. Replace if contacts remain
closed.
Compressor
runs
continually.
Does not
cycle off.
PROBLEM POSSIBLE CAUSE TO CORRECT
Place jumper across thermostat terminals. If unit operates,
replace thermostat.
Check as above.
Connect per wiring diagram.
Test for continuity at switch terminals 2 and 3.
Loss of charge in thermostat bulb.
Loose or broken parts in
thermostat.
Incorrect wiring.
System switch open.
Thermostat
does not turn
unit on.
Excessive heat load.
Restriction in line.
Refrigerant leak.
Thermostat contacts stuck.
PROBLEM POSSIBLE CAUSE TO CORRECT
Turn to highest temperature setting to see of unit will cycle off.
Disconnect power to the unit. Remove cover of thermostat
and check if contact is stuck, if so replace thermostat.
Test switch for open contacts at terminals 2 and 3 with switch
in “Off” position.
Thermostat set at coldest point
Thermostat contacts stuck.
Switch (On - Off) shorted.
Thermostat
does not
turn unit off.
Power disconnected.
System switch in “Off” position.
Branch circuit fuse blown or
circuit breaker tripped.
Inoperative system switch.
Loose or disconnected wiring at
switch.
Inoperative switch (On-Off).
Clean as recommended in Owner’s Manual.
Check for dirty or obstructed coil - clean as required.
Test for shorted thermostat or stuck contacts.
Deice coil and check for leak.
Deice coil. Check temperature differential across coil. Touch
test coil return bends for same temperature. Test for low
running current.
Test and replace if inoperative.
Check power source.
Set switch correctly.
Replace fuse, reset breaker. If repeats, check fuse or breaker
size. Check for shorts in unit wiring and components.
Test for continuity.
Check wiring and connections. Connect per wiring diagram.
Test for continuity, 3 and 2, 5 and 6.
TROUBLESHOOTING
12
PROBLEM POSSIBLE CAUSE TO CORRECT
Compressor
attempts to
start, or runs
for short
periods only.
Cycles on
overload.
Allow a minimum of two (2) minutes to allow pressures to
equalize before attempting to start.
Check voltage with unit operating. Check for other appliances
on the circuit. Unit should be on separate circuit for proper
voltage, and be fused separately.
Connect per wiring diagram.
Check by substituting a known good capacitor of correct rating.
Check for proper fan speed or blocked condenser.
Check for kinked discharge line or restricted condenser. Check
amperage.
Change compressor if all other corrections above are normal.
Compressor attempts to start
before system pressures are
equalized.
Low or fluctuating voltage.
Incorrect wiring.
Shorted or incorrect capacitor.
Restricted or low air flow through
condenser coil.
Compressor running abnormally
hot.
Overload opens too soon.
PROBLEM POSSIBLE CAUSE TO CORRECT
Compressor
does not
start - fan
motor
runs.
Check continuity of thermostat at coldest setting. Jump
contacts, if compressor runs, replace thermostat.
Check for nameplate voltage.
Test for continuity.
Check by substituting a known good capacitor of correct rating.
Check voltage at compressor terminals. If voltage is satisfactory,
replace compressor.
Replace relay
Check windings for continuity and resistance. Direct test
compressor. If direct test fails, replace compressor.
Thermostat contacts not closing.
Low voltage supply.
Switch (On-Off) inoperative.
Open capacitor.
Internal overload open.
Relay open
Open or shorted compressor
windings
PROBLEM POSSIBLE CAUSE TO CORRECT
Set to coldest position. Test thermostat and replace if
necessary.
Clean as recommended in Owner’s Manual.
Use steam or detergents to clean.
Adjust air louvers.
Clean, check for leak and make repair.
Check amperage draw against nameplate. If not conclusive,
make pressure test.
Thermostat open or inoperative.
Dirty air filter.
Dirty or plugged condenser or
evaporator coil.
Poor air circulation in area being
cooled.
Low capacity - undercharge.
Compressor not pumping
properly.
Does not
cool, or
cools only
slightly
Fan motor
does not
run.
PROBLEM POSSIBLE CAUSE TO CORRECT
Check continuity across terminals 2 and 3.
Check by substituting a known good capacitor of the same
rating.
Direct test fan motor.
Connect per wiring diagram.
Replace Relay.
Rotate by hand, add oil, if noisy, replace.
Adjust for proper clearance.
Defective switch (On-Off).
Fan capacitor open.
Inoperative fan motor.
Incorrect wiring of fan circuit.
Relay open.
Check for seized motor bearings.
Bound fan blade or blower wheel.
TROUBLESHOOTING (Continued)
13
PROBLEM POSSIBLE CAUSE TO CORRECT
Replace selector switch. Replace relay.
Selector Switch Relay
PROBLEM POSSIBLE CAUSE TO CORRECT
Refer to Installation Instructions for proper installation.
Adjust motor mount to attain proper fan blade and blower
wheel clearance.
Check for deteriorated compressor grommets, or missing
mounting parts.
Adjust and tighten as required.
Poor installation.
Fan blade striking chassis.
Compressor vibrating.
Loose cabinet parts, improperly
mounted components, tubing
rubbing.
Outside water
leaks.
Repair and clean, or replace as required.
Remove condenser shroud, Clean and remove old sealer from
base pan and shroud. Apply new sealer, reinstall and check.
Clean with steam or detergent.
Adjust fan blade to 1/2" clearance from condenser coil.
Evaporator drain pan cracked or
obstructed.
Water in center section of base
pan (compressor area).
Dirty Condenser coil.
Fan blade and slinger ring
improperly positioned.
Clean obstructed drain trough.
Evaporator drain pan broken or cracked. Reseal or replace.
Dirty evaporator coil, or extremely high humidity conditions.
Clean coil with steam or detergent.
Evaporator drain pan
overflowing.
Condensation forming on
bottom of base pan.
Water dripping from discharge
air grilles.
PROBLEM POSSIBLE CAUSE TO CORRECT
Water leaks
into room.
Switch (On-Off)
does not cut fan
motor off.
Noisy and/or
vibration.
PROBLEM POSSIBLE CAUSE TO CORRECT
TROUBLESHOOTING (Continued)
14
WIRING DIAGRAM FOR SH14J30B-A & SH20J30B-A
15
HazardGard Cabinet Parts
16
HazardGard Chassis Parts
17
HAZARDGARD PARTS LIST
REF. PART NO. DESCRIPTION APPLICATION
SS
HH
12
40
JJ
33
00
BB
--
AA
1 611-935-49 Compressor, Tecumseh, 230/208V; 60 Hz 1 Ph, Model AWG5515EXN ..................... 1
1 611-935-50 Compressor, Tecumseh, 230/208 V; 60 Hz 1 Ph, Model AWG5519EXN .................... 1
2 618-714-26 Motor, Fan 1/8 HP ......................................................................................................... 1
2 618-714-27 Motor, Fan 1/4 HP ......................................................................................................... 1
3 617-682-00 Box, Electrical Wiring.................................................................................................... 1 1
4 613-892-00 Cover, Assembly Box .................................................................................................... 1 1
5 609-353-00 Switch, On-Off DPST .................................................................................................... 1 1
* 618-297-00 Insulator, Electrical ....................................................................................................... 1 1
* 611-088-00 Relay, Solid state Haz 50 Amp ..................................................................................... 2 2
6 618-225-02 Thermostat ................................................................................................................... 1 1
7 610-805-46 Capacitor 20/7.5 MFD, 440 Volt.................................................................................... 1
7 610-805-46 Capacitor 25/7.5 MFD, 440 Volt.................................................................................... 1
8 618-298-00 Holder, Thermostat ...................................................................................................... 1 1
* 613-891-00 Connector, E.M.T........................................................................................................... 1 1
* 618-213-07 Harness, Wire, Compressor ....................................................................................... 1 1
* 618-208-01 Harness wire, Fan Motor.............................................................................................. 1 1
REFRIGERATION SYSTEM COMPONENTS
9 618-501-00 Coil, Evaporator............................................................................................................ 1
9 618-500-01 Evaporator .................................................................................................................... 1
10 620-504-00 Condenser ................................................................................................................... 1
10 620-504-01 Condenser ................................................................................................................... 1
* 013-900-05 †Capillary Tube .064 I.D. x 25” Long............................................................................ 1
* 037-605-18 †Capillary Tube .054 I.D. x 27 3/8” Long...................................................................... 2
* 608-095-00 Valve, By-Pass .............................................................................................................. 1
* 608-095-00 Valve, By-Pass .............................................................................................................. 1
* 603-081-01 Filter Drier (Install during sealed system repairs) ...................................................... 1 1
CHASSIS PARTS
11 614-939-05 Knob, Control ............................................................................................................... 1 1
12 618-294-02 Panel, Control Mounting............................................................................................... 1
12 618-294-01 Panel, Control Mounting............................................................................................... 1
* 600-713-12 Bushing, Snap.............................................................................................................. 1 1
* 600-713-11 Bushing, Snap.............................................................................................................. 1 1
* 618-293-01 Panel Plate ................................................................................................................... 1 1
* 618-299-00 Block, Insert.................................................................................................................. 11
13 618-120-06 Panel Assembly, left side ............................................................................................. 1 1
13 618-120-07 Panel Assembly, left side ............................................................................................. 1 1
ELECTRICAL PARTS
* NOT SHOWN
† CAPILLARY LENGTH MAY VARY, FLOW RATE IS THE SAME.
18
HAZARDGARD PARTS LIST
REF. PART NO. DESCRIPTION
SS
HH
12
40
JJ
33
00
BB
--
AA
APPLICATION
14 618-028-02 Partition, Control Box......................................................................................................... 1
14 618-043-02 Partition, Control Box......................................................................................................... 1
15 618-204-00 Bracket, Capacitor Mounting. ............................................................................................ 1 1
16 618-207-01 Strap, Capacitor.................................................................................................................1 1
17 618-226-02 Decorative Panel ............................................................................................................... 11
* 618-306-00 Plate, Inner Wall ................................................................................................................ 1 1
18 618-172-00 Cover, Top.......................................................................................................................... 1 1
19 618-167-00 Insulation, Top Cover ........................................................................................................ 1 1
* 618-168-00 Insulation, Left Side Deck ................................................................................................. 1 1
20 618-171-00 Deck .................................................................................................................................. 1 1
* 608-658-08 Filter, Air ............................................................................................................................. 1 1
* 608-658-09 Filter, Air ............................................................................................................................. 1 1
* 618-230-00 Holder, Filter ...................................................................................................................... 2 2
21 618-202-00 Airfoil .................................................................................................................................. 1 1
* 618-206-00 Bracket, Resistor Block..................................................................................................... 1 1
* 915-003-01 Clamp, Supply Cord .......................................................................................................... 1 1
22 605-420-03 Fan Blade .......................................................................................................................... 1
22 605-420-04 Fan Blade .......................................................................................................................... 1
23 606-106-05 Blower Wheel ....................................................................................................................1
23 606-106-01 Blower Wheel ....................................................................................................................1
24 618-033-00 Inner Wall .......................................................................................................................... 1 1
24 618-047-00 Inner Wall .......................................................................................................................... 1 1
25 618-025-00 Mount, Motor ...................................................................................................................... 1
25 618-041-00 Mount, Motor ...................................................................................................................... 1
26 618-036-01 Shroud............................................................................................................................... 1
26 618-049-00 Shroud............................................................................................................................... 1
27 618-026-00 Brace, Shroud ...................................................................................................................3 3
28 618-169-00 Insulation, Inner Wall ........................................................................................................ 1 1
28 618-169-01 Insulation, Inner Wall ........................................................................................................ 1 1
29 618-173-00 Blower Front ...................................................................................................................... 1 1
29 618-174-00 Blower Front ...................................................................................................................... 1 1
30 618-149-02 Scroll.................................................................................................................................. 1
30 618-175-01 Scroll.................................................................................................................................. 1
31 618-215-00 Door, Slide Assembly ........................................................................................................ 1 1 1
32 618-034-14 Base Pan........................................................................................................................... 1
32 618-034-14 Base Pan........................................................................................................................... 1
* 618-038-00 Drain Pan .......................................................................................................................... 1 1
* 618-188-00 Rear Grille ......................................................................................................................... 1 1
* 618-188-01 Rear Grille ......................................................................................................................... 1 1
33 610-289-00 Grommet, Compressor .................................................................................................... 3 3
34 914-004-00 Bolt, Compressor Mounting .............................................................................................. 3 3
35 618-310-00 Plenum Assembly ............................................................................................................. 1 1
* 618-093-00 Knob, Fresh Air & Exhaust................................................................................................. 1 1
* NOT SHOWN
CHASSIS PARTS (Cont.)
19
* 618-092-00 Lever, Fresh Air & Exhaust .................................................................................................. 1 1
* 618-062-00 Connector, Louver ...............................................................................................................22
* 618-063-00 Louver, Grille........................................................................................................................ 20 20
* 618-063-01 Louver with Handle ............................................................................................................. 22
36 618-032-03 Outer Shell........................................................................................................................... 1 1
36 618-046-00 Outer Shell........................................................................................................................... 1 1
37 618-089-00 Grille, Intake ........................................................................................................................ 1 1
37 618-111-00 Grille, Intake ........................................................................................................................ 1 1
* 618-199-00 Latch, Intake Grille............................................................................................................... 2 2
38 602-944-08 Wingboard........................................................................................................................... 1 1
38 602-944-09 Wingboard........................................................................................................................... 1 1
* 611-050-04 Accessory Package............................................................................................................. 1 1
* 611-050-05 Accessory Package............................................................................................................. 1 1
39 611-095-03 Bracket, Support.................................................................................................................. 2 2
40 618-197-01 Angle, Wingboard (Top) ...................................................................................................... 1 1
41 618-198-01 Angle, Wingboard (Side) ..................................................................................................... 2 2
41 618-198-03 Angle, Wingboard (Side) ..................................................................................................... 2 2
42 606-103-03 Gasket (Vinyl) ...................................................................................................................... 1 1
* 608-460-16 Bag (Assembly Hardware).................................................................................................. 1 1
* 617-173-01 Gasket, Chassis (Foam) .................................................................................................... 1 1
* 618-116-20 Carton, Shipping ................................................................................................................. 1 1
* 618-116-21 Carton, Shipping ................................................................................................................. 1 1
* 618-139-00 Pad, Shipping...................................................................................................................... 1 1
* 618-118-00 Pad, Shipping...................................................................................................................... 2 2
* 618-118-01 Pad, Shipping...................................................................................................................... 2 2
* 618-141-01 Pad, Shipping (Top) ............................................................................................................ 11
43 600-733-00 Gasket, Window (Foam) ..................................................................................................... 1 1
* Not Shown
OPTIONAL ACCESSORIES
* 01900-235 Drain – Condensate Connection Kit, DC–2 ....................................................................... x x
* 01900-312 Start Kit, Capacitor/Relay (Pow–R–Pak)............................................................................. x x
* HG2001 Parts Manual (7/01).............................................................................................................xx
* 92002403 Installation Manual .............................................................................................................. x x
HAZARDGARD PARTS LIST
REF. PART NO. DESCRIPTION
SS
HH
12
40
JJ
33
00
BB
--
AA
APPLICATION
CHASSIS PARTS (Cont.)
* NOT SHOWN
20
HG2003(1-03)
Use Factory Certified Parts.
FRIEDRICH AIR CONDITIONING CO.
Post Office Box 1540 · San Antonio, Texas 78295-1540
4200 N. Pan Am Expressway · San Antonio, Texas 78218-5212
(210) 357-4400 · FAX (210) 357-4480
www.friedrich.com
Printed in the U.S.A.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Friedrich SH14J30B-A Owner's manual

Friedrich
Brand
Friedrich
Model
SH14J30B-A
Category
Split-system air conditioners
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents