Asus 3831109820827 User manual

Brand: Asus

Model: 3831109820827

Category: Computer liquid cooling

Type: User manual

This manual is also suitable for

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on August 8

2012

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK High Flow and EK-PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASUS Rampage IV Extreme motherboard

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER.

Remove all encircled screws. There are 11 screws

on the back of the motherboard that needs to be removed in order to remove the

factory installed SB/MOSFET heatpipe cooling solution.

2. CLEANING THE PCB.

Carefully detach the original stock cooler after removing all

screws securing it to the board. Wipe off the remains (by using non–

abrasive cloth or

qtip

, as shown on sample photo) of the original thermal compound until the components

and circuit board are completely clean. EKWB recommends the use of denatured alcohol

for removing TIM leftovers.

3. APPLYING THERMAL COMPOUND.

Apply thermal compound: lightly coat the

Intel X79 PCH

(SB) with electrically non-conductive thermal grease - for example

Arctic Cooling MX-2 ™ or MX-4 ™. EKWB recommends to apply thermal grease in

cross form for best performance (see sample picture).

4. CUTTING THERMAL PADS.

Your block comes with one thermal pads

(100x16x0.5mm) which needs to be trimmed in order to fit the voltage regulation area

(VRM/MOSFET) on the motherboard’s circuit board. WARNING: DIMENSIONS ON

PICTURES BELOW ARE SCALED!

5. PLACING THERMAL PADS ON MOTHERBOARD.

Place thermal pads you cut on PCB as shown on picture bellow (PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH

SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION). EK recommends using small drops of electrically non-conductive (for example: Arctic Cooling MX-2 ™ or MX-4 ™)

thermal grease on each phase regulator (that is being covered with thermal pad; see picture below) in order to even further improve the thermal performance of the EK-FB KIT

RE4 series water block.

X79 PCH (SB)

CPU socket

Installation and mounting manual for EK-FB KIT RE4 CSQ water block:

Place 0.5mm thermal pads in larger

strips over marked area and make sure

all mosfet chips are covered.

Mosfets

Place 0.5mm thermal pads in larger strips over

the coils (inductors). This is merely to prevent

any possible short circuiting. Due to the

uneven nature of motherboard manufacturing

not all of the inductors will have contact with

the thermal pad. This is normal.

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on August 8

2012

STEP 3: PREPARING YOUR WATER BLOCK

1. PLACING SB BLOCK ON MOTHERBOARD. Place the SB part of the water block with

preinstalled 2.1mm standoffs kit gently to the motherboard or vice versa. Make sure that

mounting holes are aligned. Skip to STEP 4 on how to fasten the waterblock to the

motherboard using the enclosed screws and washers.

2. PLACING MOSFET BLOCK ON MOTHERBOARD. Place the waterblock gently to

the motherboard or vice versa. Make sure that mounting holes are aligned.

STEP 4: ATTACHING BLOCK TO MOTHERBOARD

STEP 5: CHECKING FOR CONTACTS

Prior to fastening the screws please make sure the mounting holes on the motherboard’s

circuit board are aligned with water block.

A) SB block: Use M2.5x4 DIN7985 and washers. Tighten the screws, beginning near the

southbridge, and continue evenly outwards. Do not use excessive force when tightening the

screws!

B) MOSFET block: Use ASUS factory (“stock”) backplate, two M3x8, one M3x4 DIN7985

screws and one washer. Tighten the M3x8 screws going through the backplate first and then

the remaining M3x4. Make sure you use enclosed washer underneath this screw.

Use the enclosed screws and washers as shown in picture below:

Temporarily r

emove the water block to check for uniform surface contact

between the block and the components. Note the pattern of contact on a piece

of paper. Then repeat steps 3 and 4 to reattach the block applying more or less

pressure to the areas where you have found it necessary. Note that there is no

need for perfect thermal pad imprint on the inductors/coils (mentioned in

STEP2)

6. POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

Attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. EKWB recommends using EK-PSC compression fittings with the EK-FB KIT RE4 series water

block. You can use any opening as an inlet/outlet port. Plan your tubing routing in advance!

REQUIRED TOOLS AND MOUNTING SCREWS: