5019 401 05249
Add the detergent as described in the chapter
“Detergent and Additives” in the instructions for use.
1. Turn the
programme selector knob
to the
desired programme.
2. The
remaining time display
shows the duration
of the chosen programme (in hours and minutes),
and the lamp over the
“Start”
button flashes.
3. The
programme sequence indicator
and the
predefined spin speed indication corresponding
to the selected programme lights up.
The recommended temperature (see the
indicator) can be altered by pressing the
temperature selection button under the
temperature display.
• Wash your laundry in the desired Cotton
programme, adding an appropriate amount of
chlorine bleach to the SOFTENER chamber
(close the detergent dispenser carefully).
• IMMEDIATELY after end of programme, start
the “Rinse and Spin” programme: if you want,
you can add softener.
“Eco +” button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption can be achieved.
“Prewash” button
• Only for heavily soiled laundry (e.g. sand or
granular dirt). Programme duration is increased
by some 15 min.
“Intensive Rinse” button
• An additional rinse cycle is carried out.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with detergent allergies.
“Rinse Hold” button
• The laundry remains in the last rinse water
without being spun: discoloration of the laundry
and additional creasing are prevented.
• This option is particularly recommended for the
programme “Synthetic” or “Delicate”.
• This function is particularly useful if you want to
postpone spinning to a later time.
Note:
The programme has reached the “Rinse
Hold” when the corresponding light flashes.
Terminate the “Rinse Hold” option:
• Press the “Rinse Hold” button again; the
programme will terminate automatically with the
appropriate spin cycle for the current programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to “Drain” and press
the
“Start”
button again.
“Spin Speed Reduction” button
• A maximum spin speed is assigned to each
programme.
• Press the button to set another speed for the
spin cycle.
• If no light goes on, the final spin is cancelled.
The water is only drained out.
CONSUMPTION DATA
*
Programme Temperature
(°C)
Wash
(kg)
Water
(l)
Energy
(kWh)
Programme duration
approx.**
(hours : minutes)
Cotton White/Hygiene+
95 6.0 49
***
1.90 2:00
Cotton Colours
60 6.0 44 1.14 2:20
Cotton with “Eco +” ****
60 6.0 44 1.02 2:30
Cotton Colours
40 5.0 42 0.70 2:05
Synthetics
60 2.5 60
***
0.90 1:45
Synthetics
40 2.5 55 0.60 1:30
Daily Load
40 3.0 48 0.55 1:00
Quick Wash
30 3.0 37 0.30 0:30
Delicate
30 1.5 60 0.50 0:45
Wool
40 1.0 60 0.50 0:40
Dessous / Handwash
30 1.0 45 0.40 0:35
Easy ironing
40 3.0 60 0.60 1:30
*
The
consumption values
were measured in normalized conditions in compliance with Standard IEC/EN 60456.
**
The
programme duration
may also vary from the chart values. The washing machine is able to allow for particular
household conditions and to adapt the programme run time accordingly.
***
To reduce the
water temperature
, some cold water is added at the end of the main wash cycle, before the pump
drains the water out.
****
Reference programme for energy label.
POUR IN DETERGENT, CLOSE THE
DOOR AND SELECT A PROGRAMME
USING CHLORINE BLEACH
SELECT SPECIAL OPTIONS -
The corresponding lights go on (if not
selectable: rapid flashing for 3 seconds)
With the “Start Delay” function the appliance can be run
cheaply e.g. at night, when the electricity is cheaper.
• Press the “Start Delay” button. Select the
programme start from 1 to 24 hours ahead by
pressing the button again.
• Press the
“Start”
button.
The Start Delay indicator light flashes until the
programme starts.
“Start Delay” correction.
• Before “Start” has been pressed:
The preset number of hours can be altered by
continuously pressing the “Start Delay” button.
By pressing the Start Delay button again after the
“24” setting, the time delay can be deleted again
or set again.
After “Start” has been pressed:
The preset number of hours can be reduced by
pressing the “Start Delay” button again; please
note, however, that the washing programme
starts IMMEDIATELY, as soon as you operate it
again with the Start Delay switch 01 setting.
To increase the number of hours preselected,
first turn the programme selector switch to the
“Off” position. Then set the programme and the
additional options again and select the desired
number of hours.
After you have selected the programme and eventually
the additional options, the indicator light over the
“Start”
button flashes. Turn on the tap and start the
programme by pressing the
“Start”
button. Now the
indicator light over the button goes on.
In addition, all programme phases are indicated by the
associated lights. After the end of a programme phase,
the associated indicator light goes out. Thus the
programme sequence indicator moves from left to
right across the wash, rinse and spin phases. At the end
of the programme, only the “End” indicator is still on.
As long as a washing programme is running, the lamp
lights up to show that the door cannot be opened.
When the lamp goes off, the door can be opened again.
If
“Start”
has been pressed, but the door is not latched,
the “Door Locked” indicator flashes for 10 seconds.
The door must be pushed shut within this time.
After the 10 seconds, the “Door Locked” indicator
goes out and the
“Start”
button flashes. The door
must then be opened and closed again and the
“Start”
button must be pressed.
“Pump”
Waste water is not pumped out. Check wether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
“Water Tap”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide" in the
Instructions for Use.
“Aquastop”
Lighting up of the Aquastop indication can be caused
by a leak in the appliance or hose. Please refer to the
“Troubleshooting Guide" in the Instructions for Use.
• The “End” indicator goes on.
1. Switch the washing machine off by turning the
programme selector to the “
O
”-position.
2. Turn off the tap.
3. Open the door and unload the machine.
A newly-selected programme will continue in the
same programme section during which the current
programme was interrupted. Therefore do not add
any more detergent.
1. Press the
“Start”
button to interrupt the
programme. The light flashes.
2. Select the new programme (with temperature),
any additional options and - if you wish - another
spin speed.
3. Press the
“Start”
button again to restart the
programme.
• If you are in the “Prewash” programme step, this
additional option cannot be deselected as
described (to do this see “Cancel/Reset a
running programme before the end”).
Press the
“Reset”
button for at least 2 seconds.
Any existing water is drained out before the door
can be opened.
START DELAY
PROGRAMME START
“DOOR LOCKED” INDICATOR
“TROUBLE” INDICATORS
PROGRAMME END
RESELECT AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
40105249GB.fm Page 2 Monday, September 12, 2005 3:21 PM
Black process 45.0° 100.0 LPI