Whirlpool is a registered trademark of Whirlpool USA
1
GB
Before using the dishwasher, read the
installation and maintenance instructions carefully!
5019 396 01180
ADGR 8507
1) Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to
different loads, extra functions, sensor settings (only with sensor programmes), water supply temperatures, water hardness
and power supply voltage.
2) Energy label programme in compliance with EN 50242. - Information for Test Laboratories:
for more detailed information on
the EN comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of
November 2001.
1. OVERVIEW
Programme selector
START button
The indicator lights up during operation, flashes when a fault
occurs, and goes off at the end of the programme.
START button RESET function:
Press this button for at least 2 seconds; the selected programme and
options are cancelled. Main failure displays (repeated flashing of the
START indicator lamp) can be cancelled by RESETTING. Detailed
instructions are given in chapter 5 “What to do if...”.
Salt level indicator and rinse aid level indicator
These indicator lamps light up when salt or rinse aid need to be added.
Add just before starting a wash cycle.
Fault indication and wash time display
In normal operation it indicates the remaining time (h:mm),
whereas with “Delayed start” selected it indicates the time
remaining until programme start (hh).
If “F..” appears on the display, see chapter 5 “What to do if...”.
“Delayed start” button
Press the button (repeatedly) to delay the start of the programme.
Adjustable from 1 to 24 hours. With each press of the button, the
delayed start indicator increases by one hour and after 24 restarts
from 00. Then press the START button. The dishwasher will start
after the set time.
Detergent setting upon initial use and when using a different type of detergent
1. Select the third programme in the relative table.
2. Press the START button for approx. 7 sec. to change the display.
3. Using the START button, select the desired detergent:
Display shows: 2 -1 = 2 in 1, 3 -1 = 3 in 1, 4 -1 = other combined action
detergents (in this way, the rinse aid and/or salt indicator is deactivated).
Display shows OFF = Powder detergent (factory setting).
(rinse aid level and salt level indicator activated).
4. Switch the appliance off and then switch it on again. The selected detergent
type will be indicated for approx. 3 sec.
Half Load/Multizone button
The half load cycle can be used for the upper or lower rack. Select the
required programme then press the “Half load” button. The light
comes on and goes off at the end of the programme.
This function can be used with the programmes indicated in table 1.1.
Antibacterial rinse
3)
This function activates an antibacterial rinse at the end of the wash
cycle, guaranteeing a further reduction of bacteria. Press the button to
activate or deactivate the function. This function can be used with those
programmes marked with the relative symbol in table 1.1.
The dishwasher door must be kept shut for the entire duration of
the programme in order to guarantee reduction of bacteria. If the
door is opened the indicator lamp starts flashing.
On / Off button
Table 1.1.
Table of programmes
Detergent
dispenser
Consumption
1)
P
Programmes
Selectable
extra
functions
Loading instructions large small Litres kWh Minutes
1
Pre-Rinse cold
—
Crockery to be washed later.
— — 4.0 0.03 14 ±
1)
2
Quickwash 45°C
—
Lightly soiled crockery, without dry
residuals.
X — 11.0 0.80 30 ±
1)
3
Eco
2)
50°C
Normally soiled crockery.
Energy-saving programme.
X X 11.0 1.05 155 ±
1)
4
Daily 60°C
Normally to heavily soiled
crockery.
X X 13.0 1.25 120 ±
1)
5
Intensive 70°C
Recommended programme for
heavily soiled crockery, especially
suitable for pans and saucepans.
X X 14.0 1.55 155 ±
1)
/