Astral Pool SLX Installation guide

Category
Above ground pool accessories
Type
Installation guide
8/10/2015
INSTALLATION INSTRUCTIONS
Melbourne: 03 8796 8600 Gold Coast: 07 5552 2600 Perth: 08 9350 2600
North Sydney 02 9853 2100 Townsville: 07 4796 0100 [email protected].au
Brisbane: 07 3308 5400 Adelaide: 08 8152 7600 www.astralpool.com.au
South Sydney: 02 8778 9500
Bolero ND
Cleaner
INSTALLATION INSTRUCTIONS I INSTALLATION INSTRUCTIONS
Astral Pool Underwater
Niche Lights For
Fibreglass Pools
®
Rainbow Pool Products
PO Box 2388, Mansfield Qld 4122
Telephone STD 61-7-3849 5385
Facsimile STD 61-7-3849 5384
Web: www.rainbowpoolproducts.com.au
Inst.376 Astral Pool Light Niche For Fibreglass Pool Instructions V10.15
2
Installation for Fibreglass Pools
Kit Contents
Quantity
Item
1
Fibreglass Niche Assembly
1
2030058 O-ring 8mm Fibreglass
1
2030061 Fibreglass Niche Nut
1
20348 Cable - SLX Light 20m, or
20344 Cable - SLX Light 35m
Inst.376 Astral Pool Light Niche For Fibreglass Pool Instructions V10.15
3
Installation Instructions
1. Before commencing work, check the fibreglass pane surface roughness. Rough surfaces may need
to be smoothed up by hand or power tools to allow proper water-tightness and adhesion of the silicon
sealant.
2. Cut a circular and uniform hole of 152.5mm diameter in the pool shell approximately 400mm below
the expected water line. To cut the hole, use a jig saw or 6” hole saw tool (run power tool on low rpm)
Do not install deeper than 450mm, as this makes servicing the light difficult.
Note: due to the porosity of the fibreglass wall, it is recommended to use silicone along with the O-ring
provided.
3. Run a small bead of silicone around the inner edge of the niche front lip. Ensure the silicone runs as
one continuous line.
4. Fit the niche through the hole in the pool shell. Ensure the conduit connection point is facing upwards
from the niche.
5. Apply a second heavy bead of silicone to the niche on the outside of the pool wall.
6. Lightly smear silicone into the O-ring compression recess of the collar nut (item 2030061).
7. Fit the O-ring (item 2030058) to the niche and position it near the wall.
8. Fit the collar nut over the niche and begin to tighten it. As you fasten the nut, allow the silicone to be
pushed against the pool shell wall by the O-ring.
9. Tighten the nut firmly by hand only.
Pool or Spa wall
152.5mm
Hole
Small silicone bead on inside
face of pool/spa wall
Large silicone bead on outside
face of pool/spa wall
Pool or Spa wall
Conduit entry 20 / 25mm
Inst.376 Astral Pool Light Niche For Fibreglass Pool Instructions V10.15
4
10. Clean up any excess silicone from the front and rear of the niche.
11. Allow the silicone to cure for approximately 12 to 15 hours before fitting the electrical conduit.
12. Glue a length of 25mm electrical conduit to the niche conduit socket using PVC solvent cement.
Ensure the conduit extends above the water level of the pool. If a draw wire is not being used, the
cable (item 20348 or 20344) must be fitted simultaneously with the conduit installation. Starting at the
niche, run the cable though the conduit to the power supply. Leave 1m of cable surplus inside the
niche, complete with the end of the cable with the plug, and coil up inside the niche until ready to fit
the light. Ensure the cable gland inside the niche is fully tightened around the cable.
13. Install a second conduit to return below ground level and away to the power supply. Both conduits
should be glued into a draw box to allow for future service.
Pool / Spa wall
Draw box above waterline
Conduit to DC Low
Voltage power supply
Niche
Collar Nut
To stop water siphoning
from the pool, the conduit
needs to have an air gap.
Collar Nut
Pool wall
O-ring
Silicone bead
Silicone bead
O-ring
Remove the excess silicone
Remove the excess
silicone
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Astral Pool SLX Installation guide

Category
Above ground pool accessories
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI