Audio Technica ATW-RM1 Installation And Operation

Audio Technica
Brand
Audio Technica
Model
ATW-RM1
Type
Installation And Operation

Audio Technica ATW-RM1 is a rack mount hardware kit designed for use with Audio-Technica 2000 and 3000 Series wireless systems and the ATW-DA49 antenna distribution system. This kit allows you to mount a half-rack receiver or distribution system in a 19" audio equipment rack, and also brings antennas to the front for improved reception.

The ATW-RM1 includes the following parts:

  • Long rack ear
  • Short rack ear
  • Two BNC bulkhead connectors with mounting hardware
  • Two 34" BNC-to-BNC cables
  • Six rack ear screws

To assemble the ATW-RM1, simply follow these steps:

  1. Remove the nut and lock-washer from each bulkhead connector.

Audio Technica ATW-RM1 is a rack mount hardware kit designed for use with Audio-Technica 2000 and 3000 Series wireless systems and the ATW-DA49 antenna distribution system. This kit allows you to mount a half-rack receiver or distribution system in a 19" audio equipment rack, and also brings antennas to the front for improved reception.

The ATW-RM1 includes the following parts:

  • Long rack ear
  • Short rack ear
  • Two BNC bulkhead connectors with mounting hardware
  • Two 34" BNC-to-BNC cables
  • Six rack ear screws

To assemble the ATW-RM1, simply follow these steps:

  1. Remove the nut and lock-washer from each bulkhead connector.
Professional UHF
Wireless Systems
ATW-RM1 Rack Mount Hardware Kit
Installation and Operation
Assembly Instructions/ATW-RM1 Rack-mount Hardware Kit
For use with Audio-Technica 2000 and 3000 Series wireless
systems and for the ATW-DA49 antenna distribution system.
This kit contains the hardware necessary for mounting a half-rack
receiver or distribution system in a 19" audio equipment rack; also
brings antennas to the front for improved reception.
The following parts are included:
• Long rack ear
• Short rack ear
• Two BNC bulkhead connectors with mounting hardware
• Two 34" BNC-to-BNC cables
• Six rack ear screws
Figure 1
How to assemble the ATW-RM1 Rack Mount Hardware Kit (see Fig. 1)
1. Remove the nut and lock-washer from each bulkhead connector.
Install the connectors from the front into the two holes in the long
rack ear (see Fig. 1). Note that the flat on the threaded section
must be aligned with the flat in each panel hole.
2. Install the lock-washer and nuts (included) over the back of each
bulkhead connector. Secure each connector from the back with its
lock-washer and nut, tightening the nut firmly.
3. Connect one end of each provided BNC-BNC cable to the rear
antenna input jacks on the back of the receiver (or antenna distribution
system amplifier). Attach the other end of each cable to the back of
the BNC bulkhead connectors. Make certain the bayonet twist-rings
are fully latched on the connectors at both ends.
4. Finally, mount the receiver's antennas to each of the BNC bulkhead
connectors.
Bulkhead Connector
Rubber Washer
Lock-Washer
Nut
BNC-BNC Cables
Long Rack Ear
Short Rack Ear
Antennas (not included)
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224 330/686-2600 www.audio-technica.com
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England 0113 277 1441 www.audio-technica.co.uk
P51840 ©2006 Audio-Technica U.S., Inc. Printed in U.S.A.
One-Year Limited Warranty
Audio-Technica brand products purchased in the U.S.A. are warranted for one year from date of purchase by Audio-Technica U.S., Inc. (A.T.U.S.)
to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at our option,
replaced with a new product of equal or superior value if delivered to A.T.U.S. or an Authorized Service Center, prepaid, together with the sales
slip or other proof of purchase date.
Prior approval from A.T.U.S. is required for return. This warranty excludes defects due to normal wear,
abuse, shipping damage, or failure to use product in accordance with instructions. This warranty is void in the event of unauthorized repair or
modification, or removal or defacing of the product labeling.
For return approval and shipping information, contact the Service Dept., Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law,
A.T.U.S. will have no liability for any consequential, incidental, or special damages; any
warranty of merchantability or fitness for particular purpose expires when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer for warranty details.
  • Page 1 1
  • Page 2 2

Audio Technica ATW-RM1 Installation And Operation

Audio Technica
Brand
Audio Technica
Model
ATW-RM1
Type
Installation And Operation

Audio Technica ATW-RM1 is a rack mount hardware kit designed for use with Audio-Technica 2000 and 3000 Series wireless systems and the ATW-DA49 antenna distribution system. This kit allows you to mount a half-rack receiver or distribution system in a 19" audio equipment rack, and also brings antennas to the front for improved reception.

The ATW-RM1 includes the following parts:

  • Long rack ear
  • Short rack ear
  • Two BNC bulkhead connectors with mounting hardware
  • Two 34" BNC-to-BNC cables
  • Six rack ear screws

To assemble the ATW-RM1, simply follow these steps:

  1. Remove the nut and lock-washer from each bulkhead connector.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents