Badger Basket 02234 Black Assembly Instructions Manual

Brand: Badger Basket

Model: 02234 Black

Type: Assembly Instructions Manual

This manual is also suitable for

2.0/0908/TG

MODEL NUMBERS:

SLEIGH STYLE

BABY CHANGING TABLE

Assembly

Instructions.

Adult Assembly

Required.

Save these

instructions for

future use.

Visit us online at www.badgerbasket.com

Toll-Free Customer Service: 1-800-236-1310 (Monday through Thursday 7:30 AM to 4:30 PM CST)

Web: http://www.badgerbasket.com/parts • E-mail: part[email protected]

Mail: PO Box 227, Edgar, WI 54426-0227 • Phone: 715-352-2311 • Fax: 715-352-3163

Page 1 of 6

02211 White 02212 Natural

02230 Pecan 02231 Walnut

02232 Cherry 02233 Honey

02234 Black

2.0/0908/TG

BEFORE YOU BEGIN ASSEMBLY:

Check all parts and hardware. If anything is missing or not

satisfactory, please DO NOT call the store where purchased or

return the product to them. Contact Badger Basket for assistance.

Most problems are resolved without you needing to leave home.

When contacting us, please have this instruction manual, your

product model number, and your product version code ready.

For fastest service, go to

http://www.badgerbasket.com/parts

Your Product Version Code is: 2.0/0908/TG

USE AND CARE INSTRUCTIONS:

Wipe the table, pad, and safety belt clean with a damp cloth and mild soap as needed.

READ ALL INSTRUCTIONS before use of this changing table. Keep instructions for future use.

Choking Hazard! Keep unassembled parts out of the reach of small children. Use only the parts,

hardware, and changing pad provided by Badger Basket. Do not use the changing table if it is

damaged or broken.

FALL HAZARD - To prevent death or serious injury, always keep baby within arm’s reach.

NEVER leave your baby unattended, not even for a moment, when you are changing Baby’s

diaper. ALWAYS use the safety belt provided; and as an extra precaution keep at least one hand

on your baby at all times.

DO NOT allow any children to climb or play on the table.

Periodically check to make sure all the bolts and screws remain tight.

This table is suitable for use with children weighing up to 30 lbs. (13.64 kg).

WARNING - FAILURE TO FOLLOW THESE WARNINGS

AND THE INSTRUCTIONS COULD RESULT IN

SERIOUS INJURY OR DEATH

Page 2 of 6

2.0/0908/TGPage 3 of 6

PARTS INCLUDED:

(A) 16 - Black Pegs* (one shown)

(B) 2 - Top Rails

(C1) 2 - Top Shelf Rails**

(C2) 4 - Middle/Lower Shelf Rails

(D) 2 - End Panels

(E) 16 - 1¾” Bolts (one shown)

(F1) 1 - Top Shelf Panel** (not shown)

(F2) 2 - Middle/Lower Shelf Panels

(not shown)

(G) 1 - Safety Belt

(H) 1 - Metal Support Bar

(I) 2 - 5/8” Screws (one shown)

(J) 1 - Mattress Pad (not shown)

TOOLS NEEDED:

Phillips Screwdriver (not included)

Power driver is helpful but be careful not to damage the product.

PARTS AND HARDWARE:

ASSEMBLY NOTES:

Parts & Hardware diagrams not to scale.

* Style of PEGS may vary from shown

** The two TOP SHELF RAILS have a larger

shelf groove than the other four rails. The

TOP SHELF PANEL is thicker than the

other two shelf panels.

The table can be assembled by

one person. Having a second

person available to help can

speed things along.

Don’t fully tighten the bolts

until the table is completely

assembled. Then go back and

tighten them securely, but don’t

overtighten.

C1,C2

2.0/0908/TGPage 4 of 6

STEP 1: See PICTURE 1. Insert the SIXTEEN

BLACK PEGS (A) into the 16 peg holes on the ends

of the TWO TOP RAILS (B) and the SIX SHELF

RAILS (C1, C2).

Push the thinner end of the peg (as shown by

Part B) into the hole until the wider end is flush with

the wood (as shown on Part C).

PICTURE 3

PICTURE 2

STEP 2: See PICTURE 2. Attach ONE TOP RAIL (B), ONE TOP SHELF RAIL (C1), and TWO MIDDLE/

LOWER SHELF RAILS (C2) to ONE END PANEL (D) using FOUR 1¾” BOLTS (E).

Insert the black pegs on the RAILS (B, C) into their pre-drilled holes on the END PANEL (D) to line up

the other holes for the BOLTS (E).

The shelf grooves on the SHELF RAILS (C1, C2) should face in and line up with the shelf grooves on

the END PANEL (D).

STEP 3: See PICTURE 3. Attach the second TOP RAIL (B) and the remaining THREE SHELF RAILS (C1,

C2) to the same END PANEL (D) using FOUR 1¾” BOLTS (E).

PICTURE 1

C1,C2

*You must be sure to

use the C1 rails with

the thicker grooves

in the top positions.

2.0/0908/TGPage 5 of 6

STEP 6: Note: This step can also be completed with the table upside down resting on the top which can make it

easier to position the parts and secure them with the screws.

See PICTURE 6A. Locate the SAFETY BELT (G) and slip one of the ends with the pre-made screw hole

between the TOP RAIL (B) and the TOP SHELF RAIL (C1).

See PICTURE 6B. Using the pre-drilled hole on the underside of the TOP SHELF RAIL (C1), secure the

end of the SAFETY BELT (G) and the METAL SUPPORT BAR (H) with ONE 5/8” SCREW (I).

Sandwich the end of the SAFETY BELT (G) between the metal bar and the top shelf rail as shown.

See PICTURE 6C. Repeat this step to secure the other end of the SAFETY BELT (G) and the other end of the

METAL SUPPORT BAR (H) using the second 5/8” SCREW (I).

PICTURE 4

PICTURE 5

PICTURE 6CPICTURE 6B

PICTURE 6A

*You must be sure to

use the thicker F1

shelf in the top

position.

STEP 4: See PICTURE 4. Position the table so that it’s resting on the END PANEL (D). Insert the TOP SHELF

PANEL (F1) into the shelf grooves on the TOP SHELF RAILS (C1). Insert the TWO MIDDLE/LOWER

SHELF PANELS (F2) into the shelf grooves on the MIDDLE/LOWER SHELF RAILS (C2). The white or the

colored sides of the shelves face up (depending on your model) and are seated into the grooves on all three

sides.

STEP 5: See PICTURE 5. Attach the SECOND END PANEL (D) to the TWO TOP RAILS (B) and SIX

SHELF RAILS (C1, C2) using EIGHT 1¾” BOLTS (E).

2.0/0908/TG

STEP 7: See PICTURE 7.

Put the table into its correct, upright position.

Place the MATTRESS PAD (J) onto the TOP SHELF (F1) underneath the SAFETY BELT (G).

YOUR CHANGING TABLE IS NOW ASSEMBLED!

DO NOT USE THIS PRODUCT UNTIL YOU HAVE REVIEWED

THE SAFETY INSTRUCTIONS ON PAGE 2!

The toys, accessories, and baskets shown with tables here are not included.

Page 6 of 6

PICTURE 7

Accessorize this table with our Nursery

Baskets (sold separately)!

Browse our selection of baskets at:

http://www.badgerbasket.com

Badger Basket 02234 Black Assembly Instructions Manual

Brand: Badger Basket

Model: 02234 Black

Type: Assembly Instructions Manual

This manual is also suitable for

Download PDF

report

Badger Basket 02234 Black Assembly Instructions Manual

This manual is also suitable for

Badger Basket 02234 Black Assembly Instructions Manual

Related papers

Other documents