Behringer Racktuner BTR2000 Quick start guide

Behringer
Brand
Behringer
Model
Racktuner BTR2000
Category
Supplementary music equipment
Type
Quick start guide
Quick Start Guide (Check out behringer.com for FullManual)
RACKTUNER BTR2000
Ultra-Flexible, Auto-Chromatic 2-Channel Tuner with
Metronome and Integrated Racklight
LEGAL DISCLAIMER
LIMITED WARRANTY
Important Safety
Instructions
Terminals marked with this
symbol carry electrical
current of su cient
magnitude to constitute risk of electric
shock. Use only high-quality professional
speaker cables with ¼" TS or twist-
locking plugs pre-installed. Allother
installation or modi cation should be
performed only by quali edpersonnel.
This symbol, wherever it
appears, alerts you to the
presence of uninsulated
dangerous voltage inside the enclosure -
voltage that may be su cient to
constitute a risk ofshock.
This symbol, wherever it
appears, alerts you to
important operating and
maintenance instructions in the
accompanying literature. Please read
themanual.
Caution
To reduce the risk of electric
shock, do not remove the
top cover (or the rear section). No user
serviceable parts inside. Refer servicing
to quali edpersonnel.
Caution
To reduce the risk of  re or
electric shock, do not expose
this appliance to rain and moisture.
Theapparatus shall not be exposed to
dripping or splashing liquids and no
objects  lled with liquids, such as vases,
shall be placed on the apparatus.
Caution
These service instructions
are for use by quali ed
service personnel only. Toreduce the
risk of electric shock do not perform any
servicing other than that contained in the
operation instructions. Repairshave to be
performed by quali ed servicepersonnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus
nearwater.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, stoves,
orother apparatus (including ampli ers)
thatproduceheat.
9. Do not defeat the safety purpose
of the polarized or grounding-type plug.
Apolarized plug has two blades with
one wider than the other. A grounding-
type plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
Ifthe provided plug does not  t into
your outlet, consult an electrician for
replacement of the obsoleteoutlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from theapparatus.
11. Use only attachments/accessories
speci ed by themanufacturer.
12. Use only with
the cart, stand,
tripod, bracket,
ortable speci ed by
the manufacturer,
orsold with
the apparatus. When a cart is used,
usecaution when moving the cart/
apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during
lightning storms or when unused for long
periods oftime.
14. Refer all servicing to quali ed
service personnel. Servicing is required
when the apparatus has been damaged
in any way, such as power supply cord or
plug is damaged, liquid has been spilled
or objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
orhas beendropped.
15. The apparatus shall be connected to
a MAINS socket outlet with a protective
earthingconnection.
16. Where the MAINS plug or an
appliance coupler is used as the
disconnect device, thedisconnect device
shall remain readilyoperable.
TECHNICAL SPECIFICATIONS AND
APPEARANCES ARE SUBJECT TO CHANGE
WITHOUT NOTICE AND ACCURACY
IS NOT GUARANTEED. BEHRINGER,
KLARKTEKNIK, MIDAS, BUGERA,
AND TURBOSOUND ARE PART OF THE
MUSIC GROUP MUSICGROUP.COM.
ALL TRADEMARKS ARE THE PROPERTY
OF THEIR RESPECTIVE OWNERS.
MUSICGROUP ACCEPTS NO LIABILITY
FOR ANY LOSS WHICH MAY BE
SUFFERED BY ANY PERSON WHO RELIES
EITHER WHOLLY OR IN PART UPON
ANY DESCRIPTION, PHOTOGRAPH
OR STATEMENT CONTAINED HEREIN.
COLORSAND SPECIFICATIONS MAY
VARY FROM ACTUAL PRODUCT.
MUSIC GROUP PRODUCTS ARE SOLD
THROUGH AUTHORIZED FULLFILLERS
AND RESELLERS ONLY. FULLFILLERS
AND RESELLERS ARE NOT AGENTS OF
MUSICGROUP AND HAVE ABSOLUTELY
NO AUTHORITY TO BIND MUSICGROUP
BY ANY EXPRESS OR IMPLIED
UNDERTAKING OR REPRESENTATION.
THIS MANUAL IS COPYRIGHTED.
NO PART OF THIS MANUAL MAY BE
REPRODUCED OR TRANSMITTED IN ANY
FORM OR BY ANY MEANS, ELECTRONIC
OR MECHANICAL, INCLUDING
PHOTOCOPYING AND RECORDING OF
ANY KIND, FORANY PURPOSE, WITHOUT
THE EXPRESS WRITTEN PERMISSION OF
MUSICGROUPIPLTD.
ALL RIGHTS RESERVED.
© 2013 MUSICGroupIPLtd.
Trident Chambers, Wickhams Cay,
P.O. Box 146, Road Town, Tortola,
BritishVirgin Islands
For the applicable warranty
terms and conditions and
additional information regarding
MUSICGroup’s Limited Warranty,
please see complete details online at
www.music-group.com/warranty.
Las terminales marcadas con
este símbolo transportan
corriente eléctrica de
magnitud su ciente como para constituir
un riesgo de descarga eléctrica.
Utilicesolo cables de altavoz
profesionales y de alta calidad con
conectores TS de 6,3 mm o de bayoneta
pre jados. Cualquier otra instalación o
modi cación debe ser realizada
únicamente por un técnicocuali cado.
Este símbolo, siempre que
aparece, leadvierte de la
presencia de voltaje
peligroso sin aislar dentro de la caja;
estevoltaje puede ser su ciente para
constituir un riesgo dedescarga.
Este símbolo, siempre que
aparece, leadvierte sobre
instrucciones operativas y
de mantenimiento que aparecen en la
documentación adjunta. Por favor,
leaelmanual.
Atención
Para reducir el riesgo de
descarga eléctrica, no quite
la tapa (olaparte posterior). Nohay
piezas en el interior del equipo que
puedan ser reparadas por el usuario.
Sies necesario, póngase en contacto con
personal cuali cado.
Atención
Para reducir el riesgo
de incendio o descarga
eléctrica, no exponga este aparato a la
lluvia, humedad o alguna otra fuente que
pueda salpicar o derramar algún líquido
sobre el aparato. Nocoloque ningún
tipo de recipiente para líquidos sobre
elaparato.
Atención
Las instrucciones de servicio
deben llevarlas a cabo
exclusivamente personal cuali cado.
Paraevitar el riesgo de una descarga
eléctrica, no realice reparaciones que no
se encuentren descritas en el manual
de operaciones. Lasreparaciones deben
ser realizadas exclusivamente por
personalcuali cado.
1. Lea las instrucciones.
2. Conserve estas instrucciones.
3. Preste atención a todas
lasadvertencias.
4. Siga todas las instrucciones.
5. No use este aparato cerca del agua.
6. Limpie este aparato con un pañoseco.
7. No bloquee las aberturas de
ventilación. Instale el equipo de acuerdo
con las instrucciones del fabricante.
8. No instale este equipo cerca de
fuentes de calor tales como radiadores,
acumuladores de calor, estufas u otros
aparatos (incluyendo ampli cadores)
quepuedan producir calor.
9. No elimine o deshabilite nunca la
conexión a tierra del aparato o del cable
de alimentación de corriente. Unenchufe
polarizado tiene dos polos, uno de los
cuales tiene un contacto más ancho que
el otro. Una clavija con puesta a tierra
dispone de tres contactos: dos polos y
la puesta a tierra. El contacto ancho y el
tercer contacto, respectivamente, son
los que garantizan una mayor seguridad.
Siel enchufe suministrado con el equipo
no concuerda con la toma de corriente,
consulte con un electricista para cambiar
la toma de corriente obsoleta.
10. Coloque el cable de suministro de
energía de manera que no pueda ser
pisado y que esté protegido de objetos
a lados. Asegúrese de que el cable de
suministro de energía esté protegido,
especialmente en la zona de la clavija y en
el punto donde sale del aparato.
11. Use únicamente los dispositivos o
accesorios especi cados por elfabricante.
12. Use
únicamente
la carretilla,
plataforma, trípode,
soporte o mesa
especi cados por
el fabricante o suministrados junto
con el equipo. Altransportar el equipo,
tengacuidado para evitar daños y caídas
al tropezar con algúnobstáculo.
13. Desenchufe el equipo durante
tormentas o si no va a utilizarlo durante
un periodo largo.
14. Confíe las reparaciones únicamente
a servicios técnicos cuali cados.
Launidad requiere mantenimiento
siempre que haya sufrido algún daño,
si el cable de suministro de energía o el
enchufe presentaran daños, sehubiera
derramado un líquido o hubieran caído
objetos dentro del equipo, si el aparato
hubiera estado expuesto a la humedad
o la lluvia, si ha dejado de funcionar de
manera normal o si ha sufrido algún
golpe o caída.
15. Al conectar la unidad a la toma de
corriente eléctrica asegúrese de que la
conexión disponga de una unión a tierra.
16. Si el enchufe o conector de red sirve
como único medio de desconexión, éste
debe ser accesiblefácilmente.
LAS ESPECIFICACIONES TÉCNICAS Y LA
APARIENCIA EXTERIOR ESTÁN SUJETAS
A CAMBIOS SIN PREVIO AVISO Y NO
PODEMOS GARANTIZAR LA TOTAL
EXACTITUD DE TODO LO QUE APARECE
AQUÍ. BEHRINGER, KLARK TEKNIK,
MIDAS, BUGERA, YTURBOSOUND
SON PARTE DEL GRUPOMUSIC GROUP
MUSICGROUP.COM. TODAS LAS
MARCAS REGISTRADAS SON PROPIEDAD
DE SUS RESPECTIVOS DUEÑOS.
MUSICGROUP NO ACEPTA NINGÚN TIPO
DE RESPONSABILIDAD POR POSIBLES
Instrucciones de
seguridad
NEGACIÓN LEGAL
2 3Quick Start GuideRACKTUNER BTR2000
Page is loading ...
Page is loading ...
(EN) Controls
RACKTUNER BTR2000 Controls
Operating elements on the left side of the BTR2000
(1)
(7)
(2) (3) (4) (5) (6)
(8) (9) (10) (11)
Control elements on the right side of the BTR2000
(1)
(7)
(2) (3) (4) (5) (6)
(8) (9) (10) (11)
Serial number and sockets on the rear of the BTR2000
MO DEL BT R2000
CONCE IVE D AN D DE SIG NED BY
BEHRIN GER GERMAN Y.
MAD E IN CHINA
CA UTION
REPL ACE FUS E WITH S AM E
FUS E TY PE A ND R ATIN G.
AT TENTION
UTILI SER U N FUSIB LE D E REC HANGE
DE ME ME T YP E ET C AL IBRE.
(RING = MUTE)
MUT E SEL ECT SOUND MAIN
INPUTOUTPU TFOOT SW IT CH
2 1
AC POWER
INPUT
CA UTIO N
RISK OF EL ECTRIC SHOCK!
DO NOT OPEN!
ATTENTION
RISQUE DE CHOC ELECTR IQUE!
NE PAS OUVRIR!
CA UTION
TO R EDU CE T HE RISK OF FI RE O R ELE CT RIC
SHO CK D O NO T EX PO SE T HIS E QUIP MEN T
TO R AI N OR MOI ST URE.
(12) (13) (14) (15) (16) (17)
(6) LED bar
Tuner mode: The LED bar indicates
how far the note played deviates
from the ideal during instrument
tuning. Thescaleof the display can
be toggled between ±50 cents and
±10cents.
Metronome mode: The graphical
metronome display uses the LEDbar.
(7) DISPLAY
Various values–tuner mode, pitch,
BPM–are shown in thisdisplay.
(8) MUTE/LIGHT button.
The BTR2000 comes with a
rack light. It is switched on
and o witha long tap on the
MUTE/LIGHT button.
Tuner mode: Pressing the
MUTE/LIGHT button briey mutes
the entire MAIN output.
Metronome mode: Unlike in
tuner mode, briey pressing the
MUTE/LIGHT button only mutes
the metronome click and not the
entire MAIN output; the instrument
remains audible.
(9) INPUT SELECT button.
Tuner mode: Depending on your
application, you must use and/
or select dierent inputs on the
BTR2000. You can toggle between
the two channels by pressing the
INPUT SELECT button.
Metronome mode: Pressing
this button starts or stops
the metronome (acoustic and
opticalindicator).
(10) SOUND/METRONOME button.
To switch between tuner and
metronome mode you must
press and hold the SOUND/
METRONOMEbutton.
Tuner mode: Briey pressing this
button switches the reference
tone on or o. The volume of the
reference tone can be set with
thewheel.
Metronome mode: When the
SOUND/METRONOME button is
pressed briey, you can adjust
the volume of the metronome click
using the wheel.
(11) The POWER button switches on
theBTR2000.
To disconnect the power from
the unit, unplug the power cord.
When you start up the unit,
ensure that the plug is easily
accessible. If the unit is mounted
in a rack, pleaseensure easy power
disconnection with a plug or
all-pole switch.
(12) SERIAL NUMBER
(13) MUTE
You can connect a single footswitch
(such as the BEHRINGERDUAL
A/B SWITCH AB200) to the
¼" TS MUTE connector.
(14) SELECT
You can connect a double
footswitch (such as the
BEHRINGERFS112) to the
¼" stereo SELECT connector.
(15) SOUND
The SOUND connector can output
the sounds generated by the unit
(reference tone, metronome click).
(16) MAIN
Depending on the cable
connections on the BTR2000 the
MAIN connector can either output
the sounds generated by the unit
and the instrument signal or the
instrument signal alone.
(17) INPUT 1 and INPUT 2
You can connect one or two
instruments to the unit via the
INPUT 1 and INPUT 2 connectors.
The built-in microphone is available
only when INPUT 2 is selected.
(1) The built-in microphone MIC can
be used to tune the instrument and
calibrate the standard “A”pitch To
do this, you must select INPUT 2 and
press the MUTE button.
(2) You can plug your instrument into
the INPUT 1 connector on the front
of the BTR2000. This connector takes
priority over the INPUT 1 connector
on the rear panel. Ifthere are
instruments plugged into both the
front and back INPUT1 connectors
at the same time, theunit only
evaluates the signal of the
instrument plugged into the front.
(3) MODE/FINE
[DISPLAY/MODE] button.
Tuner mode: Afterpressing this
button briey you can select a tuner
mode (e.g. guitar or bass) using the
control (5).
A long press of the button toggles
the scaling of the LED bar between
1cent/LED and 5 cents/LED.
Metronome mode: Press this button
to toggle the metronome display
between a ashing light and a
needlesimulation.
(4) TRANSPOSE/REF [TAP] button.
Tuner mode: A short tap on this
button lets you use the wheel for
transposition. Keepingthe button
pressed longer lets you calibrate the
standard “A” pitch.
Metronome mode: The BTR2000 can
recognize and save a tempo that is
entered by pressing the [TAP] button
at least 4 times in rhythm.
(5) The wheel is used to change the
parameters of the various functions.
For example, it is used to set the BPM
of the metronome or the frequency
of standard “A.” A ashing light
indicates which function can be set
using this control.
8 RACKTUNER BTR2000 9 Quick Start Guide
Page is loading ...
Page is loading ...
Specications Especicaciones técnicas
14 15Quick Start GuideRACKTUNER BTR2000
Audio Connectors
INPUT 1 ¼" TS connector on the front and back
Input impedance 1 MΩ, relay hard bypass
INPUT 2 ¼" TS connector
Input impedance 1 MΩ, buered
SOUND ¼" TS connector
Output impedance 4.5 kΩ
MAIN ¼" TS connector
Output impedance 500 Ω
Connector for Footswitch
MUTE ¼" TS connector
SELECT ¼" TRS connector
Tuner
Scale 12 equally tempered notes
Frequency range 27.5Hz to 4186Hz
Reference tone for manual or
automatic calibration
440 Hz ±12 Hz
Display scale ±50 Cent (±0.5 half steps)
Display resolution ±1cent, ±5 cents
Metronome
Tempo range 30BPM - 240BPM
Racklight
Illumination 4 x LED, 5 mm, white
Power Supply
Power Range
USA/Canada 120 V~, 60 Hz
China 220 V~, 50 Hz
Europe/U.K./Australia 240 V~, 50 Hz
Japan 100 V~, 50 - 60 Hz
Power consumption 9 W
Dimensions/Weight
Dimensions (H x W x D) approx. 1.73 x 4.45 x 19.02" / 440 x 113 x 483mm
Weight approx. 2.73 lbs / 1.24kg
Conexiones de Audio
INPUT 1 jack mono de 6,3 mm en la parte delantera y trasera
Impedancia de entrada 1 MΩ, hard bypass por relé
INPUT 2 jack mono de 6,3 mm
Impedancia de entrada 1 MΩ, amortiguada
SOUND jack mono de 6,3 mm
Impedancia de salida 4,5 kΩ
MAIN jack mono de 6,3 mm
Impedancia de salida 500 Ω
Conexiones Para Pedal
MUTE jack mono de 6,3 mm
SELECT jack mono de 6,3 mm
Anador
Escala 12 notas bien temperadas
Rango de frecuencias 27,5Hz - 4186Hz
Tono de referencia para calibración
manual o automática
440 Hz ±12 Hz
Rango ±50 Cent (pasos de ±0,5 semitonos)
Resolución ±1Cent, ±5 Cent
MetrÓnomo
Tempo 30BPM - 240BPM
Lámpara
Tipo 4 x LED, 5 mm, blanca
Suministro de Corriente
Tensión de Red
EE.UU./Canadá 120 V~, 60 Hz
China 220 V~, 50 Hz
Europa/R.U./Australia 230 V~, 50 Hz
Japón 100 V~, 50 - 60 Hz
Consumo de potencia 9 W
Dimensiones/Pesos
Dimensiones (anch. x alt. x prof.) approx. 1,73 x 4,45 x 19,02" / 440 x 113 x 483mm
Peso approx. 2,73 lbs / 1,24kg
Page is loading ...
Page is loading ...
Other important information
1. Register online. Pleaseregister
your new MUSIC Group equipment
right after you purchase it by visiting
behringer. com. Registeringyour purchase
using our simple online form helps us to
process your repair claims more quickly
and eciently. Also, read the terms and
conditions of our warranty, ifapplicable.
2. Malfunction. Should your
MUSICGroup Authorized Reseller not be
located in your vicinity, you may contact
the MUSIC Group Authorized Fulller for
your country listed under “Support” at
behringer. com. Shouldyour country not be
listed, pleasecheck if your problem can be
dealt with by our “OnlineSupport” which
may also be found under “Support” at
behringer. com. Alternatively, please submit
an online warranty claim at behringer. com
BEFORE returning theproduct.
3. Power Connections.
Beforeplugging the unit into a power
socket, please make sure you are using the
correct mains voltage for your particular
model. Faulty fuses must be replaced
with fuses of the same type and rating
withoutexception.
1. Registro online.
Lerecomendamos que registre su nuevo
aparato MUSIC Group justo después de
su compra accediendo a la página web
behringer. com. Elregistro de su compra a
través de nuestro sencillo sistema online
nos ayudará a resolver cualquier incidencia
que se presente a la mayor brevedad
posible. Además,aproveche para leer
los términos y condiciones de nuestra
garantía, siesaplicable en sucaso.
2. Averías. En el caso de que no
exista un distribuidor MUSIC Group en
las inmediaciones, puede ponerse en
contacto con el distribuidor MUSIC Group
de su país, queencontrará dentro del
apartado “Support” de nuestra página web
behringer. com. En caso de que su país no
aparezca en ese listado, acceda a la sección
“Online Support” (quetambiénencontrará
dentro del apartado “Support” de nuestra
páginaweb) y compruebe si su problema
aparece descrito y solucionado allí.
Deforma alternativa, envíenos a través
de la página web una solicitud online de
soporte en periodo de garantía ANTES de
devolvernoselaparato.
3. Conexiones de corriente.
Antes de enchufar este aparato a una salida
de corriente, asegúrese de que dicha salida
sea del voltaje adecuado para su modelo
concreto. En caso de que deba sustituir un
fusible quemado, deberáhacerlo por otro de
idénticas especicaciones, sinexcepción.
1. Enregistrez-vous enligne.
Prenezle temps d’enregistrer votre
produit MUSIC Group aussi vite que
possible sur le site Internet behringer. com.
Lefait d’enregistrer le produit en ligne
nous permet de gérer les réparations
plus rapidement et plus ecacement.
Prenezégalement le temps de lire les
termes et conditions de notregarantie.
2. Dysfonctionnement. Si vous
n’avez pas de revendeur MUSIC Group près
de chez vous, contactez le distributeur
MUSIC Group de votre pays: consultez la
liste des distributeurs de votre pays dans
la page “Support” de notre site Internet
behringer. com. Si votre pays n’est pas
dans la liste, essayez de résoudre votre
problème avec notre “aideen ligne”
que vous trouverez également dans la
section “Support” du site behringer. com.
Vouspouvez également nous faire parvenir
directement votre demande de réparation
sous garantie par Internet sur le site
behringer. com AVANT de nous renvoyer
leproduit.
3. Raccordement au secteur.
Avant de relier cet équipement au secteur,
assurez-vous que la tension secteur de
votre région soit compatible avec l’appareil.
Veillez à remplacer les fusibles uniquement
par des modèles exactement de même
taille et de même valeur électrique — sans
aucuneexception.
Important information
Aspectos importantes
Informations
importantes
1. Online registrieren.
Bitteregistrieren Sie Ihr neues
MUSICGroup-Gerät direkt nach dem Kauf
auf der Website behringer. com. WennSie
Ihren Kauf mit unserem einfachen online
Formular registrieren, könnenwir Ihre
Reparaturansprüche schneller und
ezienter bearbeiten. Lesen Sie bitte
auch unsere Garantiebedingungen,
fallszutreend.
2. Funktionsfehler. Sollte sich
kein MUSIC Group Händler in Ihrer Nähe
benden, können Sie den MUSIC Group
Vertrieb Ihres Landes kontaktieren, der auf
behringer. com unter „Support“ aufgeführt
ist. Sollte Ihr Land nicht aufgelistet sein,
prüfen Sie bitte, ob Ihr Problem von
unserem „Online Support“ gelöst werden
kann, den Sie ebenfalls auf behringer. com
unter „Support“ nden. Alternativ reichen
Sie bitte Ihren Garantieanspruch online
auf behringer. com ein, BEVOR Sie das
Produktzurücksenden.
3. Stromanschluss. Bevor Sie das
Gerät an eine Netzsteckdose anschließen,
prüfen Sie bitte, obSie die korrekte
Netzspannung für Ihr spezielles Modell
verwenden. Fehlerhafte Sicherungen
müssen ausnahmslos durch Sicherungen
des gleichen Typs und Nennwerts
ersetztwerden.
1. Registre-se online. Porfavor,
registreseu novo equipamento
MUSICGroup logo após a compra visitando
o site behringer. com Registrar sua compra
usando nosso simples formulário online
nos ajuda a processar seus pedidos de
reparos com maior rapidez e eciência.
Além disso, leia nossos termos e condições
de garantia, caso sejanecessário.
2. Funcionamento Defeituoso.
Casoseufornecedor MUSIC Group não esteja
localizado nas proximidades, vocêpode
contatar um distribuidor MUSICGroup
para o seu país listado abaixo de “Suporte”
embehringer. com. Se seu país não estiver
na lista, favor checar se seu problema pode
ser resolvido com o nosso “SuporteOnline”
que também pode ser achado abaixo
de “Suporte”em behringer. com.
Alternativamente, favorenviar uma
solicitação de garantia online em
behringer. com ANTES da devolução
doproduto.
3. Ligações. Antes de ligar a unidade
à tomada, assegure-se de que está a
utilizar a voltagem correcta para o modelo
em questão. Osfusíveis com defeito
terão de ser substituídos, sem qualquer
excepção, porfusíveis do mesmo tipo e
correntenominal.
Weitere wichtige
Informationen
Outras Informações
Importantes
21Quick Start Guide20 RACKTUNER BTR2000
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
Responsible Party Name: MUSIC Group Services USInc.
Address: 18912 North Creek Parkway,
Suite 200 Bothell, WA 98011, USA
Phone/Fax No.: Phone: +1 425 672 0816
Fax: +1 425 673 7647
RACKTUNER BTR2000
complies with the FCC rules as mentioned in the followingparagraph:
This equipment has been tested and found to comply with the limits
for a ClassB digital device, pursuant to part 15 of the FCC Rules.
Theselimits are designed to provide reasonable protection against
harmful interference in a residential installation. Thisequipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
Ifthis equipment does cause harmful interference to radio or television
reception, whichcan be determined by turning the equipment o and
on, theuser is encouraged to try to correct the interference by one or
more of the followingmeasures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician forhelp.
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
includinginterference that may cause undesired operation.
Important information:
Changes or modications to the equipment not expressly approved by
MUSIC Group can void the user’s authority to use the equipment.
RACKTUNER BTR2000
23Quick Start Guide22 RACKTUNER BTR2000
We Hear You
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Behringer Racktuner BTR2000 Quick start guide

Behringer
Brand
Behringer
Model
Racktuner BTR2000
Category
Supplementary music equipment
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents