WIRELESS N
ACCESS POINT
USER
MANUAL
MODELS:
525404, 524728,524735
INT-525404/524728/524735-UM-0214-04
Federal Communications Commission
Interference Statement
FCC Part 15
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This equipment must be installed and operated in accordance with provided
instructions, and a minimum of 20 cm of space (approx. 8 inches) must be
provided between any computer-mounted antenna and a person’s body
(excluding hands, wrists and feet) during wireless modes of operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference;
and (2) This device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate the equipment.
Federal Communications Commission (FCC) Radiation Exposure
Statement
This equipment complies with FCC radiation exposure set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 20 cm (8 inches) during normal operation.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
The equipment version marketed in the U.S. is restricted to usage of
channels 1-11 only.
R&TTE Compliance Statement
This equipment complies with all the requirements of Directive 1999/5/EC of
the European Parliament and the Council of March 9, 1999, on radio
equipment and telecommunication terminal equipment and the mutual
recognition of their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station
Equipment) as of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who
install and use it. However, special attention must be paid to the dangers of
electric shock and static electricity when working with electrical equipment. All
guidelines of this and of the computer manufacturer must therefore be allowed
at all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria,
Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy,
Luxembourg, the Netherlands, Portugal, Spain, Sweden and the United
Kingdom.
The ETSI version of this device is also authorized for use in EFTA member
states Iceland, Liechtenstein, Norway and Switzerland.
EU Countries Not Intended for Use
None.
Table of Contents
Chapter I: Product Information ................................................... 1
1-1 Product Introduction............................................................................1
1-2 Safety Information...............................................................................2
1-3 System Requirements.........................................................................3
1-4 Package Contents...............................................................................4
1-5 Connections and Indicators.................................................................5
Chapter II: System and Network Setup ...................................... 7
2-1 Installing the access point to your Network.........................................7
2-2 Connecting to wireless access point by web browser.........................8
2-2-1 Windows 95/98/Me IP address setup .................................................. 8
2-2-2 Windows 2000 IP address setup ....................................................... 10
2-2-3 Windows XP IP address setup .......................................................... 12
2-2-4 Windows Vista IP address setup ....................................................... 14
2-2-5 Connecting to Web Management Interface ....................................... 17
2-3 View System Status and Information ................................................19
2-4 Select an Operating Mode for Wireless Access Point.......................21
2-4-1 AP Mode ............................................................................................ 23
2-4-1-1 Multiple ESSID ........................................................................ 25
2-4-2 Station-Infrastructure ......................................................................... 26
2-4-2-1 Wireless Site Survey ............................................................... 28
2-4-3 AP Bridge-Point to Point Mode .......................................................... 29
2-4-4 AP Bridge-Point to Multi-Point Mode ................................................. 32
2-4-5 AP Bridge-WDS Mode ....................................................................... 34
2-4-6 Universal Repeater............................................................................ 36
2-5 WPS Setting......................................................................................39
2-6 Advanced Wireless Settings..............................................................42
2-7 Wireless Security ..............................................................................45
2-7-1 Disable Security................................................................................. 47
2-7-2 WEP................................................................................................... 48
2-7-3 WPA Pre-shared Key ......................................................................... 50
2-7-4 WPA RADIUS .................................................................................... 52
2-7-5 802.1x Authentication ........................................................................ 54
2-8 Radius Server ...................................................................................56
2-9 MAC Filtering ....................................................................................59
2-10 System Utilities................................................................................61
2-10-1 Change Password ........................................................................... 61
2-10-2 IP Address of the Wireless Access Point......................................... 62
2-10-3 DHCP Server ................................................................................... 64
Chapter III: Advanced Configuration........................................ 66
3-1 Configuration Backup and Restore ...................................................66
3-2 Firmware Upgrade ............................................................................67
3-3 System Reset....................................................................................68
Chapter IV: Troubleshooting..................................................... 69
Chapter V: Glossary................................................................... 71
1
Chapter I: Product Information
1-1 Product Introduction
Thank you for purchasing this INTELLINET NETWORK
SOLUTIONS
TM
Wireless 150N Access Point, Model 525404;
Wireless 300N Access Point, Model 524728; or Wireless 300N PoE
Access Point, Model 524735. With this cost-efficient wireless
access point, computers and wireless devices that are compatible
with 802.11 Draft-N can be connected to an existing wired Ethernet
network at speeds of up to 150 Mbps (Model 525404) or 300 Mbps
(Models 524728 and 524735).
Easy install procedures allow computer users to set up a network
environment in a relatively short time.
Other features of this access point include:
Compatible with IEEE 802.11b/g/Draft-N wireless network
standard — works with other 802.11b/g/Draft-N wireless
devices.
Allows wireless devices to connect to existing wired network and
share network resources.
Supports DHCP server function.
Supports 64/128-bit WEP, WPA, and WPA2 wireless data
encryption.
Supports MAC address filtering: only allows specific wireless
devices of your choice to connect to this access point.
Supports RADIUS server: only allows users listed in your
authorization server to use wireless network.
Supports WPS (Wi-Fi Protected Setup): simplifies wireless client
setup procedures. Even inexperienced users can set up a
wireless network without a network technician’s help.
Easy-to-use Web-based user interface for network configuration
and management purposes.
Three-Year Warranty
2
1-2 Safety Information
To maintain the safety of users and property, follow these safety
instructions:
1. This access point is designed for indoor use only; DO NOT
place this access point outdoors.
2. DO NOT put this access point in or near hot or humid places,
like a kitchen or bathroom. Also, do not leave this access point
in your car in hot weather.
3. DO NOT pull any connected cable with force; disconnect it from
the access point first.
4. If you want to place this access point at any significant height or
hang it on a wall, make sure it’s firmly secured. Falling from any
height would damage the access point and its accessories.
5. Accessories of this access point, like the antennas and power
supply, are dangers to small children under 3 years of age.
They may put the small parts in their nose or mouth, possibly
causing injury. KEEP THIS ACCESS POINT OUT THE REACH
OF CHILDREN!
6. The access point will become hot when in use for long time.
This is normal and is not a malfunction. DO NOT put this
access point on paper, cloth or other flammable materials.
7. There’s no user-serviceable part inside the access point. If the
access point is not working properly, contact your dealer and
ask for help. DO NOT disassemble the access point.
8. If the access point falls into water when it’s powered, DO NOT
use your hands to pick it up. Switch the electrical power off
before you do anything, or contact an experienced electrical
technician for help.
9. If you smell something strange or even see some smoke
coming from the access point or power supply, remove the
power supply or switch the electrical power off immediately and
call the dealer for help.
3
1-3 System Requirements
Computer or network devices with a wired or wireless network
interface card.
Web browser (Microsoft Internet Explorer 4.0 or above,
Netscape Navigator 4.7 or above, Opera Web browser or Safari
Web browser).
An available AC power socket (100 – 240 V, 50/60 Hz).
4
1-4 Package Contents
Before you start to use this access point, check to see if there’s
anything missing in the package. If so, contact your dealer of
purchase.
Wireless Access Point (main body, 1 pc.)
3dBi Dipole Antenna (Model 525404; 1 pc.; Models 524728 and
5
24
735: 2 pcs.)
Quick Install Guide (1 pc.)
User Manual on CD (1 pc.)
A/C Power Adapter (1 pc.)
5
1-5 Connections and Indicators
Front Panel
LED Name
Light
Status
Description
PWR
On
The access point is switched on and correctly
powered.
On
Wireless WPS mode is enabled.
Off
Wireless network is switched off.
WLAN
Flashing
Wireless LAN activity (transferring or receiving
data).
On
LAN port is connected.
Off
LAN port is not connected.
LAN
Flashing
LAN activity (transferring or receiving data).
6
Back Panel
Item Name
Description
Antennas
One or two reserve SMA antenna connectors for attaching
3 dBi detachable antennas enclosed with the product.
Power
Power connector; connects to A/C power adapter.
LAN
Local area network (LAN) port.
Reset / WPS
Reset the router to factory default settings (clear all settings)
or start the WPS function. Press this button and hold it in for
10 seconds to restore all settings to factory defaults; press
this button for less than 5 seconds to start the WPS function.
7
Chapter II: System and Network Setup
2-1 Installing the access point to your Network
Follow these instructions to build the network connection between
your new wireless access point and your computer’s network
devices:
1. Connect the access point to the router or switch/hub in your
network through the LAN port of the access point using Ethernet
cable.
2. Connect the A/C power adapter to the wall socket, then connect
it to the Power jack of the access point.
3. Check all LEDs on the front panel. The PWR LED should be
steadily on; the LAN LED should be on if the access point is
correctly connected to the ADSL modem, router or switch/hub. If
the PWR LED is not on, or if any LED you expect to be on isn’t,
recheck the cabling or refer to 4-2 Troubleshooting for possible
causes and solutions.
8
2-2 Connecting to wireless access point by Web browser
After the network connection is made, the next step is to set up the
access point with proper network parameters so it can work
properly in your network environment.
Before you can connect to the access point and start configuration
procedures, your computer must be able to get an IP address
automatically (use a dynamic IP address). If it’s set to use a static
IP address, or if you’re unsure, follow the instructions below to
configure your computer to use a dynamic IP address:
If the operating system of your computer is….
Windows 95/98/Me - Go to section 2-2-1
Windows 2000 - Go to section 2-2-2
Windows XP - Go to section 2-2-3
Windows Vista - Go to section 2-2-4
2-2-1 Windows 95/98/Me IP address setup
1. Click the Start button (it should be located at lower-left corner of
your computer), then click Control Panel. Double-click the
Network icon to display the Network window. Select “TCP/IP,”
then click “Properties.”
9
2. Select “Specify an IP address,” then enter the following settings
in their respective fields:
IP address: 192.168.2.2
Subnet Mask: 255.255.255.0
Click “OK when finished.
10
2-2-2 Windows 2000 IP address setup
1. Click the Start button (it should be located at lower-left corner of
your computer), then click Control Panel. Double-click the
Network and Dial-up Connections icon, then double-click
Local Area Connection. The Local Area Connection
Properties window will appear. Select “Internet Protocol
(TCP/IP),” then click “Properties.”
11
2. Select “Use the following IP address,” then enter the following
settings in their respective fields:
IP address: 192.168.2.2
Subnet Mask: 255.255.255.0
Click “OK when finished.
12
2-2-3 Windows XP IP address setup
1. Click the Start button (it should be located at lower-left corner of
your computer), then click Control Panel. Double-click the
Network and Internet Connections icon, click Network
Connections, then double-click Local Area Connection. The
Local Area Connection Status window will appear. Click
“Properties.”
13
2. Select “Use the following IP address,” then enter the following
settings in their respective fields:
IP address: 192.168.2.2
Subnet Mask: 255.255.255.0
Click “OK when finished.
14
2-2-4 Windows Vista IP address setup
1. Click the Start button (it should be located at lower-left corner of
your computer), then click Control Panel. Click View Network
Status and Tasks, then click Manage Network Connections.
Right-click Local Area Netwrok, then select “Properties.” The
Local Area Connection Properties window will appear. Select
“Internet Protocol Version 4 (TCP / IPv4),” then click
“Properties.”
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI