Kozyheat Chaska XL Owner's manual

DIRECT VENT FIREPLACE INSERT

WARNING: This product must be installed by

a licensed plumber or gas fitter when installed

in the Commonwealth of Massachusetts.

IMPORTANT: Installation of a CO detector is

required in the fireplace room when installed in

the Commonwealth of Massachusetts.

◙ Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

IF YOU SMELL GAS:

◙ Do not light any appliance.

◙ Do not touch any electrical switch: do not use any phone in your building.

◙ Immediately call gas supplier from a neighbors phone. Follow the gas supplier instructions.

◙ If you cannot reach your gas supplier, call the fire department.

◙ Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

WARNING: If the information in these instructions are not followed exactly, a fire or

explosion may result, causing property damage, personal injury or loss of life.

This appliance is only for use with the type (s) of gas indicated on

the rating plate. A conversion kit is supplied with the appliance.

www.kozyheat.com

INSTALLATION

AND

OPERATION MANUAL

Quality Fireplaces for Life

DO NOT

DISCARD

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

June - 2009

CSK-335-REV-07

Shown with Young Pattern Full Door Shroud

A manufactured home (USA only) or mobile home OEM installation must conform with the Manufac-

tured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or when such a standard is

not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or Stan-

dard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4

This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home,

where not prohibited by local codes.

CONGRATULATIONS!

We welcome you as a new owner of a Kozy Heat gas fireplace. Kozy Heat

products are designed with superior components and materials and assembled by

trained craftsmen who take pride in their work. The burner and valve assembly are

100% test-fired and the complete fireplace is thoroughly inspected before packaging

to ensure that you receive a quality product. Our commitment to quality and

customer satisfaction have remained the same for over 30 years. We offer a

complete line of gas and wood fireplaces, unique cabinets and stylish accessories to

compliment any décor. Adding a fireplace is one of the best ways to increase the

value of your home and we are proud to offer a network of dealers throughout the

country to help make your experience everything you imagine. We pride ourselves in

being dedicated to not only function and reliability, but customer safety as well.

We offer our continual support and guidance to help you achieve the maximum

benefit and enjoyment from your Kozy Heat gas fireplace.

Jim Hussong Dudley Hussong

President Board Chairman

INTRODUCTION

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

Homeowner Reference Information

We recommend that you record the following information about your fireplace.

Model Name:______________________________ Date purchased/installed:____________

Serial Number:____________________________ Location on fireplace:_______________

Dealership purchased from:__________________ Dealer Phone:_____________________

Notes:_____________________________________________________________________

__________________________________________________________________________

PAGE 1

TABLE OF CONTENTS

PAGE 2

INTRODUCTION

Introduction and Homeowner Reference Information 1

CONTENTS

Table of Contents 2

SAFETY INFORMATION

Safety Information 3

FEATURES

Features 4

COMMONWEALTH OF MASSACHUSETTS INFORMATION

Commonwealth of Massachusetts Information 5

SPECIFICATIONS

Fireplace Dimensions 6

Clearances 6

Components List 7

Additional Components Required 7

Placement Clearance Requirements 7

EXISTING FIREPLACE SPECIFICATIONS

Existing Fireplace Requirements 8

PREPARE EXISTING FIREPLACE

Existing Fireplace Minimum Opening Requirements 9

Prepare Existing Fireplace 9

FAN DIRECT WIRE INSTALLATION

CSK-335 /CSK-335-RAD Fan Direct Wire Installation 10

CSK-335-RF Fan Direct Wire Installation 11

THERMOSTAT / WALL SWITCH / REMOTE - CSK-335

Thermostat / Wall Switch / Remote - CSK-335 12

GLASS FRAME ASSEMBLY

Glass Frame Assembly Removal 13

Glass Frame Assembly Installation 13

INSTALLATION

Approved Venting 14

Combustion Air Venting Options 14

Air Duct Removal 14

Kozy Heat #816-CL Co-Linear Vent System 15

Run Vent System Through Existing Chimney 16

Connect Vent System to Air Duct 17

Position Fireplace Insert 17

GAS LINE CONNECTION

Gas Line Connection 18

Check Millivolt Board Installation 18

COMPLETE FAN WIRING INSTALLATION

CSK-335 / CSK-335-RAD Complete Fan Wiring Installation 19

CSK-335-RF Complete Fan Wiring Installation 19

3 PIECE SHROUD ASSEMBLY AND INSTALLATION

3 Piece Shroud Assembly and Installation 20

LOG SET INSTALLATION

Log Set Installation 21

MILLIVOLT BOARD REMOVAL

Millivolt Board Removal 22

MILLIVOLT BOARD INSTALLATION

Millivolt Board Installation 23

CSK-335 OPERATING INSTRUCTIONS

CSK-335 / CSK-335-RAD Valve and Pilot Assembly Components 24

CSK-335 / CSK-335-RAD Lighting and Shutdown Instructions 25-27

CSK-335 / CSK-335-RAD Pressure Testing 28

CSK-335-RF OPERATING INSTRUCTIONS

CSK-335-RF Valve and Pilot Assembly Components 29

CSK-335-RF Lighting and Shutdown Instructions 30-32

CSK-335-RF Pressure Testing 33

CSK-335-RF Remote Receiver Functions 34-35

FINALIZING THE INSTALLATION

Flame Appearance 36

To Adjust Venturi 36

MAINTENANCE

Maintenance 37

TROUBLESHOOTING (CSK-335)

Troubleshooting (CSK-335 / CSK-335-RAD ) 38-40

TROUBLESHOOTING (CSK-335-RF)

RF Remote Troubleshooting (CSK-335-RF) 41

Troubleshooting (CSK-335-RF) 42-43

REPLACEMENT PARTS LIST

Replacement Parts List 44

WARRANTY

Warranty 45-46

Installation and repair should be done only by a qualified service person. The appliance should be

inspected by a qualified service person before use. Annual inspection by a qualified service person is

required to maintain warranty. More frequent cleaning may be required due to excessive lint from

carpeting, bedding materials, etc. It is imperative that control compartments, burners and

circulation air passageways of the appliance be kept clean.

If this appliance is installed directly on carpeting, tile or other combustible material other than wood

flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth

of the appliance.

Children and adults should be alerted to the hazards of high surface temperatures and should stay

away to avoid burns or clothing ignition.

Young children should be carefully supervised when they are in the same room as the appliance.

Clothing or other flammable material should not be place on or near the appliance.

Adequate accessibility clearances for servicing and proper operation must be maintained.

This appliance must not share or be connected to a chimney flue serving any other appliance.

Keep area around the appliance clear of combustible materials, gasoline and other flammable vapor

and liquids.

The flow of combustion and ventilation air must not be obstructed.

Due to high temperatures the appliance should be located out of traffic and away from furniture and

draperies.

The glass front or any part removed for servicing the appliance must be replaced prior to operating

the appliance. Work should be done by a qualified service technician.

Clean glass only when cool and only with non-abrasive cleansers.

Do not operate this appliance with the glass/frame assembly removed, cracked or broken. The glass

assembly, Part #CXL-057T, shall only be replaced as a complete unit, as supplied by Hussong Mfg.

Co., Inc. Replacement of the glass assembly must only be performed by a licensed or qualified service

person. DO NOT SUBSTITUTE MATERIALS.

Do not strike or slam glass assembly.

Any safety screen or guard removed for servicing the appliance must be replaced prior to operating

the appliance.

Under no circumstances should any solid fuel (wood, coal, paper or cardboard etc.) be used in this

appliance.

Keep burner and control compartment clean.

Do not use this fireplace if any part has been under water. Immediately call a qualified service

technician to inspect this appliance and to replace any part of the control system and any gas control

which has been under water.

This fireplace has been tested to and complies with ANSI Z21.88a-2007·CSA 2.33a-2007·CSA P.4.1-02 “VENTED GAS FIREPLACE

HEATERS” by OMNI-Test Laboratories, Portland, OR. Installation must conform with local building codes or in the absence of local

building codes, with the National Fuel Gas Code, ANSIZ223.1/NFPA 54 - Current Edition, or the Natural or Propane Installation Code,

CSAB149.1

SAFETY INFORMATION

PAGE 3

High efficiency

High quality lifetime glass

18” x 32” (457 mm x 813 mm)

Quick latch glass frame assembly

Co-linear vent system - 3” combustion air / 3” exhaust

Innovative vent connection system

Engineer-designed burner system

High - Low regulator

Modulating valve system w/ fan and flame adjustment, remote

control (Kozy Kontrol)*

**Automatic fan kit (2) - 75 CFM

Refractory brick lining

(2) hoods / lower grill (black)

Minnesota Energy Code compliant to 50 pascals

*Standard on CSK-335-RF models

**Standard on CSK-335 and CSK-335-RF models

Red brick refractory

Standard size or custom sized (3 & 4 pc.) shrouds

Surrounds

Flex vent adaptor kit

Remote control* or thermostat remote control

Wall mount thermostat / wireless wall mount thermostat

Decorative full door faces in various styles and finishes

Mission design doors in various finishes

Various cabinet & flush surrounds

Fan Kit (CSK-335-RAD Models)

Speed Control / Receptacle Assembly (CSK-335-RAD Models)

*Standard on RF models

Each unit factory tested!

Tested by OMNI - Test Laboratories

Sealed combustion chamber with standing pilot ignition

Removable millivolt board with 30-second delay pilot

Automatic pressure relief glass system

Requires no electricity to operate (excluding fan)

Bedroom and mobile home approved

Fireplace Weight (as packaged for shipment)

155 lbs. (70.31 kg)

FEATURES

STANDARD FEATURES

OPTIONAL FEATURES

WEIGHT

SAFETY FEATURES

PAGE 4

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS

NOTE: The following requirements reference

various Massachusetts and national codes not

contained in this manual.

For all sidewall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes,

including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than (7) feet above finished grade in the

area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

INSTALLATION OF CARBON MONOXIDE DETECTORS

At the time of installation of the side wall horizontally vented gas fueled equipment, the installing plumber or gas-fitter shall observe that a hard wired

carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the in-

stalling plumber or gas-fitter shall observe that a battery operated or hard wired carbon monoxide detector is installed on each additional level of the dwell-

ing, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the

services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or attic, the hard wired carbon monoxide detector with

alarm and battery back-up may be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30)

days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with

an alarm shall be installed.

APPROVED CARBON MONOXIDE DETECTORS

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS

certified.

SIGNAGE

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum of eight (8) feet above grade directly in

line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print no less the one-half

inch (1/2”) in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

INSPECTION

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the

inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08 (2) (a) 1 through 4.

EXEMPTIONS

The following equipment is exempt from 248 CMR 5.08 (2) (a) 1 through 4:The equipment listed in Chapter 10 entitled “Equipment Not Required To Be

Vented” in the most current edition of NFPA 54 as adopted by the Board; and Product Approved side wall horizontally vented gas fueled equipment in-

stalled in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system compo-

nents with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

Detailed instructions for the installation of the venting system design or the venting system components; and

A complete parts list for the venting system design or venting system.

MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED

When the manufacturer of Product Approved side wall horizontally vented gas equipment does not provide the parts for venting the flue gases, but identi-

fies “special venting systems”, the following requirements shall be satisfied by the manufacturer:

The referenced “special venting systems” instructions shall be included with the appliance or equipment installation instructions and;

The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and de-

tailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists

for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

PAGE 5

TOP

FRONT

RIGHT

LEFT

24

3

8

"

619mm

32"

813mm

18

1

8

"

460mm

23"

584mm

33

3

8

"

848mm

11"

279mm

5"

127mm

16"

406mm

17

1

4

"

438mm

5

1

8

"

130mm

9

1

2

"

241mm

1

7

8

"

48mm

TOP

FRONT

RIGHT

LEFT

24

3

8

"

619mm

32"

813mm

18

1

8

"

460mm

23"

584mm

33

3

8

"

848mm

11"

279mm

5"

127mm

16"

406mm

17

1

4

"

438mm

5

1

8

"

130mm

9

1

2

"

241mm

1

7

8

"

48mm

TOP

FRONT

RIGHT

LEFT

24

3

8

"

619mm

32"

813mm

18

1

8

"

460mm

23"

584mm

33

3

8

"

848mm

11"

279mm

5"

127mm

16"

406mm

17

1

4

"

438mm

5

1

8

"

130mm

9

1

2

"

241mm

1

7

8

"

48mm

FIREPLACE DIMENSIONS

DESCRIPTION Height Width Back Width Depth Back Height Back to Elec.

Access

Back to Gas

Line Access

Front to Vent

Center

Back to Vent

Center

FIREPLACE

DIMENSIONS

INCHES 23 33-3/8 24-3/8 16 17-1/4 9-1/2 5-1/8 11 5

MILLIMETERS 876 1038 743 406 438 241 130 279 127

SPECIFICATIONS

MINIMUM CLEARANCES TO COMBUSTIBLES

Insert to sidewall: 12” (305 mm)

Insert top to 9” (229 mm) mantel: 16” (406 mm)

Insert top to 3/4” (20 mm) trim: 12” (305 mm)

Insert bottom to combustible floor in front: 6” (152 mm)

Insert bottom to combustible floor underneath: 0” (0 mm)

PAGE 6

WARNING: FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THESE DIAGRAMS OR FAILURE TO USE

ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY DAMAGE OR

PERSONAL INJURY.

1. Fireplace insert

2. Spring-loaded latch glass assembly

3. Millivolt board with burner cover

4. Co-linear air duct

5. Log set (see page 21)

6. Refractory panels

Model CSK-335 includes 150 CFM fan with limit

switch and speed control.

Model CSK-335-RF includes modulating valve on

millivolt board, fan kit and remote control.

TOP

FRONT

RIGHT

LEFT

24

3

8

"

619mm

32"

813mm

18

1

8

"

460mm

23"

584mm

33

3

8

"

848mm

11"

279mm

5"

127mm

16"

406mm

17

1

4

"

438mm

5

1

8

"

130mm

9

1

2

"

241mm

1

7

8

"

48mm

PLACEMENT CLEARANCE REQUIREMENTS

This fireplace must be installed on a level surface capable of supporting the fireplace and venting.

Fireplace must be placed directly on wood or non-combustible surface (not linoleum or carpet) extending the entire depth and width

of fireplace.

Due to high surface temperatures, fireplace should be located out of traffic and away from furniture and draperies.

This fireplace may be installed in a bedroom.

Please be aware of the large amount of heat this fireplace will produce when determining a location.

SPECIFICATIONS

PAGE 7

MODEL #CSK-335 COMPONENTS LIST

(#CXL-770) - Millivolt Board Assembly with 18” Flexible

Gas Line attached

(#700-203) - Manual Gas Shut-off Valve

(#CXL-135) - Burner Assembly

(#CXL-G900) - Refractory Set

(#CXL-50A) - Log Package

(#CXL-057T) - Glass Frame Assembly

(#OCK-H50L) - LP Conversion Kit

(#816-CL1) - Co-Linear Air Duct

(#CSK-028) - Fan Kit (2)-75 CFM

(#500-CXL) - Grill Assembly

MODEL #CSK-335-RF COMPONENTS

(#CXL-800-RF) - Millivolt Board Assembly with 18” Flexible

Gas Line attached

(#700-203) - Manual Gas Shut-off Valve

(#CXL-135) - Burner Assembly

(#CXL-G900) - Refractory Set

(#CXL-50A) - Log Package

(#RF-028) - RF Fan Kit

(#CXL-057T) - Glass Frame Assembly

(#OCK-H50L-RF) - LP Conversion Kit

(#700-108) - Remote control

(#816-CL1) - Co-Linear Air Chute

(#500-CXL) - Grill Assembly

ADDITIONAL COMPONENTS REQUIRED

Vent System; Part # 816-CL: For use with minimum 6” x 8” I.D. masonry or 7” I.D. Class A metal chimneys - Includes 12 ft. (3.66 m)

compressed, expandable to 35 ft (10.67 m) co-linear 3” x 3” flexible chimney, and termination cap.

Other approved venting: ICC, Selkirk, American Metals, Simpson Dura-Vent

Shroud - 3 pc & 4 pc.: Standard shrouds are available for this insert and will fit most applications. Custom shrouds may be ordered on a

non-returnable basis. When ordering a custom shroud, please specify the existing fireplace front opening height and

width. An upper hood and lower grill are included with fireplace.

or

Blank Shrouds - 3 & 4 pc.: Blank shrouds are available for on-site custom fit applications and are sized to the opening after the insert has

been installed. The interior perimeter is properly sized to fit onto the insert. The outer perimeter must be cut,

formed and finished (painted). An upper hood and lower grill are included with fireplace.

or

Full Door Shrouds: Full door decorative shrouds are available for this insert and are used in place of a standard or blank shroud. An upper

hood and lower grill are included with fireplace.

MODEL #CSK-335-RAD COMPONENTS LIST

Refer to Model #CSK-335 list.

All components same with the exception of the fan kit.

Model #CSK-335-RAD does not include a fan kit.

EXISTING FIREPLACE SPECIFICATIONS

THIS INSERT IS APPROVED FOR INSTALLATION IN MASONRY AND FACTORY-BUILT SOLID FUEL BURNING FIREPLACES.

EXISTING FIREPLACE REQUIREMENTS

The existing fireplace & chimney must be clean and in good working order and constructed of non-combustible materials.

A gas line must be able to be installed to the insert.

Provisions made to provide electrical power to operate the insert fan and thermostatic control (if used).

Any chimney clean-outs must fit properly.

Existing Chimney must be comprised of one of the following: Class „A‟ metal chimney: 7” minimum inside diameter.

Masonry Chimney: 6" x 8" minimum inside diameter.

Existing Chimney Height: Minimum: 12 ft. (3.66m)

Maximum: 35 ft. (10.67m)

Determine length of your existing chimney:

1. Remove and discard existing chimney cap.

2. With one person at the fireplace and another person at the top of chimney,

measure from fireplace base to the top of chimney.

Subtract 23” (584 mm) (height of insert).

This is the total length of co-linear flexible aluminum you will require.

MEASUREMENT FROM FIREPLACE BASE TO TOP OF CHIMNEY:______________

LESS 23" (584 mm) (HEIGHT OF INSERT): -23" (584 mm) .

TOTAL CHIMNEY LENGTH REQUIRED: ______________

NOTE: It is helpful to have two people complete the

next step in determining chimney height.

MIN. 12 ft. (3.66 m)

MAX. 35 ft. (10.67 m)

CAUTION: THIS APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY

FLUE SERVING A SEPARATE SOLID-FUEL BURNING APPLIANCE.

PAGE 8

EXISTING FIREPLACE MINIMUM OPENING REQUIREMENTS

(A) Height: 23-1/2" (597 mm)

(B) Front Width : 33-1/2" (851 mm)

(C) Depth: 16-1/2" (419 mm)

(D) Back Width : 24-1/2" (622 mm)

All dimensions are minimum requirements

The firebrick (refractory), glass doors, screen rails, screen mesh and log grates can be removed in order to gain minimum gas

insert opening requirements.

Any smoke shelves, shields and baffles may be removed from firebox if attached with mechanical fasteners.

WARNING: CUTTING ANY SHEET-METAL PARTS OF THE FIREPLACE, IN WHICH THE GAS FIREPLACE IS TO BE

INSTALLED, IS PROHIBITED.

PREPARE THE EXISTING FIREPLACE

PAGE 9

1. The refractory, glass doors, screen rails, screen mesh and log grates may be removed from existing fireplace before installing this gas

fireplace insert.

2. Any smoke shelves, shields and baffles may be removed if attached by mechanical fasteners.

3. If necessary, remove firebrick on sides and back of the existing fireplace to obtain at least the minimum opening requirements listed

above.

4. The fireplace flue damper can be fully blocked open or removed for installation of this gas fireplace insert.

5. Remove existing chimney cap.

6. Clean chimney and inside of fireplace to prevent creosote smell from entering the home.

7. Place „THIS UNIT HAS BEEN MODIFIED‟ label in the bottom of existing firebox so it will be visible if this gas fireplace insert is

removed.

8. Run electrical wiring if hard wiring to the pre-installed electrical box in the insert if desired. See „FAN DIRECT WIRE INSTALLA-

TION‟ instructions on following pages.

9. Run any electrical wiring needed if insert is to be run by a thermostat.

WARNING: CUTTING ANY SHEET-METAL PARTS OF THE FIREPLACE, IN WHICH THE GAS FIREPLACE IS TO BE

INSTALLED, IS PROHIBITED.

PREPARE THE EXISTING FIREPLACE

PAGE 10

Incoming wiring

110V-120V

FAN DIRECT WIRE INSTALLATION

#CSK-335

#CSK-335-RAD OPTIONAL FAN KIT #CSK-028

CSK-335:This fireplace insert comes complete with a fan and thermostatic control switch already installed. A speed control, receptacle,

and 8 ft. (2.44 m) fan cord have been installed, wired and mounted in a removable electrical box panel on the right side of the fireplace. If

wiring to the pre-installed electrical box is desired, the wiring should be run prior to permanently setting the insert in place and connecting

the vent system.

NOTE: If this fireplace insert is being installed in the minimum opening dimensions,

the wiring may need to be completed after the fireplace insert is set in place.

WARNING: This appliance is equipped with a three-prong (grounding) plug for

protection against shock hazard and should be plugged directly into a properly

grounded three-prong receptacle. Do not cut or remove the grounding prong from

this plug. Do not allow any excess fan cord to touch the fireplace.

NOTE: Code approved line voltage wiring 14 gauge or better must be used when

wiring this assembly. Refer to your local electrical codes for specific requirements in

your area.

Speed Control / Receptacle Assembly

Temperature Switch:

Magnetically attaches to bottom of

firebox.

Electrical Box

60Hz

110V-120V

Ground Wire

DIRECT WIRE INSTALLATION:

NOTE: The cord must be removed and wiring disassembled.

Insert 110V-120V wiring (with ground) through the romex connector and

wire to speed control / receptacle assembly, matching black, white & green

(ground) wires to the corresponding wires on the speed control / receptacle

assembly.

DIRECT WIRE INSTALLATION

1. Loosen (but do not remove) screw securing removable access panel (with electrical box & romex connector installed) from the

right side of fireplace. Remove access panel.

2. Remove (2) screws securing speed control / receptacle to expose wiring.

3. Remove existing cord and insert 110V-120V wiring (with ground) through romex connector, wiring to speed control / receptacle

assembly, matching black (hot), white (neutral), and green (ground) wire to the corresponding wires on speed control / receptacle

assembly. NOTE: The (3) wire nuts obtained when removing existing cord may be used for this purpose.

4. Secure speed control / receptacle assembly into the electrical box with (2) screws provided.

Refer to page 19 for instructions on completing fan wiring after insert has been installed.

This appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes,

with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Codes, CSA C22.1

DIRECT WIRE CONNECTION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.

CSK-335-RAD: A speed control, receptacle, with 8 ft. (2.44 m) fan cord wired and mounted in an electrical box panel (#600-083C) is

available. If hardwiring to the electrical box is desired, the wiring should be run prior to permanently setting the insert in place and con-

necting the vent system.

CSK-335-RF (only) FAN DIRECT WIRE INSTALLATION

#CSK-335-RF (ONLY) INSTRUCTIONS

A receptacle and 8 ft. (2.44m) fan cord have been installed, wired, and mounted in a removable electrical box panel on the right side of the

fireplace. If direct wiring to the pre-installed electrical box is desired, wiring should be completed prior to permanently positioning insert

and connecting the vent system.