Paradyne Hotwire 7976 User manual

Category
Networking
Type
User manual
HOTWIRE
7974, 7975, 7976,
7984, 7985, AND 7986
STANDALONE
TERMINATION UNIT
USER’S GUIDE
Document No. 7970-A2-GB20-00
August 1999
Printed on recycled paper
A
7970-A2-GB20-00
August 1999
Copyright E 1999 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be copied or distributed,
transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form
or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the
express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.
Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation
reserves the right to revise this publication and to make changes from time to time in the contents hereof without
obligation of Paradyne Corporation to notify any person of such revision or changes.
Changes and enhancements to the product and to the information herein will be documented and issued as a new
release to this manual.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor directly for any help needed. For
additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor
locations, or Paradyne worldwide office locations, use one of the following methods:
H Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty
at www.paradyne.com/warranty.)
H Telephone: Call our automated system to receive current information by fax or to speak with a company
representative.
Within the U.S.A., call 1-800-870-2221
Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them to Technical Publications,
Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to [email protected]. Include
the number and title of this document in your correspondence. Please include your name and phone number if you
are willing to provide additional clarification.
Trademarks
All products and services mentioned herein are the trademarks, service marks, registered trademarks or registered
service marks of their respective owners.
Important Information
B
7970-A2-GB20-00 August 1999
!
Important Safety Instructions
1. Read and follow all warning notices and instructions marked on the product or included in the manual.
2. Input power to this product must be provided by one of the following: (1) a UL Listed/CSA Certified power source
with a Class 2 or Limited Power Source (LPS) output for use in North America; or (2) a 24 Vdc National Electric
Code (NEC) ANSI/NFPA 70/Canadian Electric Code (CEC) Class 2 circuit installed in accordance with articles
110-16, 110-17, and 110-18 of the NEC, and articles 2-308, 2-310, 2-312, 2-314, 2-200, and 2-202 of the CEC, or
(3) a Safety Extra Low Voltage (SELV) power source with a maximum available output of less than 240 VA,
certified for use in the country of installation.
3. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to
protect it from overheating, these slots and openings must not be blocked or covered.
4. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the
power cord.
5. Do not attempt to install or service this product yourself, as opening or removing covers may expose you to
dangerous high voltage points or other risks. Refer all installation and servicing to qualified service personnel.
6. General purpose cables are provided with this product. Special cables, which may be required by the regulatory
inspection authority for the installation site, are the responsibility of the customer.
7. When installed in the final configuration, the product must comply with the applicable Safety Standards and
regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory
agencies and inspection authorities to ensure compliance.
8. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If
products installed in separate buildings are interconnected, the voltage potential may cause a hazardous
condition. Consult a qualified electrical consultant to determine whether or not this phenomenon exists and, if
necessary, implement corrective action prior to interconnecting the products.
9. In addition, if the equipment is to be used with telecommunications circuits, take the following precautions:
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the
network interface.
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of
electric shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak.
Important Information
C
7970-A2-GB20-00
August 1999
EMI Warnings
!
WARNING:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
The authority to operate this equipment is conditioned by the requirements that no modifications will be
made to the equipment unless the changes or modifications are expressly approved by Paradyne
Corporation.
!
WARNING:
To Users of Digital Apparatus in Canada:
This Class A digital apparatus meets all requirements of the Canadian interference-causing equipment
regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du règlement sur le matérial
brouilleur du Canada.
i
7970-A2-GB20-00
August 1999
Contents
About This Guide
Document Purpose and Intended Audience vii. . . . . . . . . . . . . . . . . . . . . . . . .
Document Summary vii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product-Related Documents viii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 About the Hotwire 79xx Standalone Termination Unit
M/SDSL and M/HDSL Overview 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hotwire 79xx Standalone Termination Unit Features 1-2. . . . . . . . . . . . . . . . .
Network Configuration 1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel LED Status Indicators 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Panel Interface Connections 1-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP Management Capabilities 1-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management Information Base (MIB) Support 1-6. . . . . . . . . . . . . . . . . . .
SNMP Trap Support 1-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Using the Asynchronous Terminal Interface
User Interface Access 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communication Port Settings 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initiating an ATI Session 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen Work Areas 2-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigating the Screens 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard Keys 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen Function Keys 2-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching Between Screen Work Areas 2-8. . . . . . . . . . . . . . . . . . . . . . . .
Ending an ATI Session 2-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents
ii
7970-A2-GB20-00
August 1999
3 Initial Startup and Configuration
Overview 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Power 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to an Optional External +24 Vdc Power Source 3-2. . . . . . .
Connecting to the Network 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to a DTE 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ferrite Choke (Model 7975 Only) 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to a System Terminal 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering Identity Information 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Choosing a Configuration Method 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the Unit Using the Configuration Menus 3-7. . . . . . . . . . . . . . . . .
Accessing and Displaying Configuration Options 3-8. . . . . . . . . . . . . . . . . . . .
Configuration Edit/Display 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration Loader 3-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving Configuration Options 3-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Download Code 3-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Configuring the Unit Using the Internal Switches
Overview 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the Unit Using the Internal Switches 4-2. . . . . . . . . . . . . . . . . . . .
Switchpack Locations 4-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switchpack Definitions for Models 7974 and 7984 4-4. . . . . . . . . . . . . . .
Switchpack Definitions for Models 7975 and 7985 4-6. . . . . . . . . . . . . . .
Switchpack Definitions for Models 7976 and 7986 4-9. . . . . . . . . . . . . . .
5 Monitoring the Unit
What to Monitor 5-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing System and Test Status 5-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Health and Status Messages 5-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Self-Test Results Messages 5-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test Status Messages 5-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Network Error Statistics 5-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Network Performance Statistics 5-9. . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing DSX-1 Performance Statistics (Models 7974, 7984) 5-11. . . . . . . . . .
Viewing G.703 Performance Statistics (Models 7976, 7986) 5-13. . . . . . . . . .
Using the Display LEDs Screen 5-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hotwire 79xx Standalone Termination Unit LEDs 5-16. . . . . . . . . . . . . . . . . . . .
Contents
iii
7970-A2-GB20-00
August 1999
6 Testing
Accessing the Test Menu 6-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Running Network Tests 6-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Line Loopback 6-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Network Send Line Loopback 6-4. . . . . . . . . . . . . . . . . . . . . . . . .
Send and Monitor 511 6-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSX-1 Tests (Models 7974, 7984) 6-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSX-1 Repeater Loopback 6-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSX-1 DTE Loopback 6-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SYNC Data Port Tests (Models 7975, 7985) 6-9. . . . . . . . . . . . . . . . . . . . . . . .
Data Terminal Loopback 6-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Channel Loopback 6-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Send Remote Data Channel Loopback 6-12. . . . . . . . . . . . . . . . . . . . . . . . .
G.703 Tests (Models 7976, 7986) 6-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G.703 Repeater Loopback 6-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G.703 DTE Loopback 6-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Tests 6-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lamp Test 6-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ending an Active Test 6-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Telco-Initiated Tests (Models 7974, 7984) 6-18. . . . . . . . . . . . . . . . . . . . . . . . . .
Telco-Initiated Line Loopback 6-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Telco-Initiated Payload Loopback 6-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Telco-Initiated Remote Line Loopback 6-19. . . . . . . . . . . . . . . . . . . . . . . . . .
7 Messages and Troubleshooting
Overview 7-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring SNMP Traps 7-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Messages 7-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 7-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents
iv
7970-A2-GB20-00
August 1999
8 Security
Overview 8-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ATI Access Levels 8-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating a Login 8-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deleting a Login 8-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting the Unit’s COM Port or Factory Defaults 8-6. . . . . . . . . . . . . . . . . . .
Controlling SNMP Access 8-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assigning SNMP Community Names and Access Types 8-7. . . . . . . . . .
Limiting SNMP Access through the IP Addresses of the Managers 8-7.
9 IP Addressing
Selecting an IP Addressing Scheme 9-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configurations Not Running IP Conservative Software 9-1. . . . . . . . . . .
All Configurations 9-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IP Addressing Example 9-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A Configuration Option Tables
Overview A-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Interface Options Menu A-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSX-1 Interface Options (Models 7974, 7984) A-4. . . . . . . . . . . . . . . . . . . . . .
Synchronous Data Port Options (Models 7975, 7985) A-6. . . . . . . . . . . . . . . .
G.703 Interface Options (Models 7976, 7986) A-10. . . . . . . . . . . . . . . . . . . . . . .
System Options Menu A-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communication Port A-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management and Communication Options Menu A-17. . . . . . . . . . . . . . . . . . . .
Telnet Session Options A-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communication Protocol Options A-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General SNMP Management Options A-22. . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP NMS Security Options A-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP Traps Options A-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents
v
7970-A2-GB20-00
August 1999
B Standards Compliance for SNMP Traps
SNMP Traps B-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
warmStart B-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
authenticationFailure B-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
linkUp and linkDown B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enterprise-Specific Traps B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C Cables and Pin Assignments
Overview C-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSL Network Interface Cable C-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COM Port Interface Cable C-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Input Connector C-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Power Cable C-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSX-1/G.703 Network Interface C-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EIA-530-A Port C-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EIA-530-A-to-X.21 Interface C-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EIA-530-A-to-RS-449 Interface C-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EIA-530-A-to-V.35 Interface C-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D Technical Specifications
Glossary
Index
Contents
vi
7970-A2-GB20-00
August 1999
This page intentionally left blank.
vii
7970-A2-GB20-00
August 1999
About This Guide
Document Purpose and Intended Audience
This guide contains information needed to set up, configure, and operate the
Hotwire 7974, 7975, 7976, 7984, 7985, and 7986 Multirate Symmetric Digital
Subscriber Line (M/SDSL) and Multirate High-bit-rate DSL (M/HDSL) Standalone
Termination Units, and is intended for installers and operators.
Document Summary
Section Description
Chapter 1
About the Hotwire 79xx Standalone Termination Unit.
Describes the unit’s features and capabilities.
Chapter 2
Using the Asynchronous Terminal Interface.
Provides
instructions for accessing the user interface and navigating
through the screens.
Chapter 3
Initial Startup and Configuration.
Provides procedures for
setting up the user interface and for configuring the unit
using the asynchronous terminal interface.
Chapter 4
Configuring the Unit Using the Internal Switches.
Provides
procedures for configuring the unit using the internal
switches instead of the asynchronous terminal interface.
Chapter 5
Monitoring the Unit.
Describes using the LEDs, status, and
network statistics to monitor the unit.
Chapter 6
Testing.
Provides information about available tests and test
setup.
Chapter 7
Messages and Troubleshooting.
Provides information on
SNMP traps, device messages, and troubleshooting.
Chapter 8
Security.
Presents procedures for creating a login, setting
the effective access levels, and controlling SNMP access.
Chapter 9
IP Addressing.
Provides information and examples
regarding IP addresses.
About This Guide
viii
7970-A2-GB20-00
August 1999
Section Description
Appendix A
Configuration Option Tables.
Contains all configuration
options, possible settings, and default settings.
Appendix B
Standards Compliance for SNMP Traps.
Contains SNMP
trap compliance information.
Appendix C
Cables and Pin Assignments.
Contains connector and
interface information.
Appendix D
Technical Specifications.
Contains physical and regulatory
specifications, network and port interfaces, power
consumption values, and accessory part numbers.
Glossary Defines acronyms and terms used in this document.
Index Lists key terms, acronyms, concepts, and sections in
alphabetical order.
Product-Related Documents
Document Number Document Title
7970-A2-GN10
Hotwire 7974, 7975, 7976, 7984, 7985, and 7986
Standalone Termination Unit Installation Instructions
8774-A2-GB20
Hotwire 8774 M/SDSL Termination Unit, with DSX-1
Interface, User’s Guide
8775-A2-GB20
Hotwire 8775 M/SDSL Termination Unit User’s Guide
8776-A2-GB20
Hotwire 8776 M/SDSL Termination Unit, with G.703
Interface, User’s Guide
8784-A2-GB20
Hotwire 8784 M/HDSL Termination Unit, with DSX-1
Interface, User’s Guide
8786-A2-GB20
Hotwire 8786 M/HDSL Termination Unit, with G.703
Interface, User’s Guide
Contact your sales or service representative to order additional product
documentation.
Paradyne documents are also available on the World Wide Web at
www.paradyne.com. Select
Library
Technical Manuals.
1-1
7970-A2-GB20-00
August 1999
About the Hotwire 79xx
Standalone Termination Unit
1
M/SDSL and M/HDSL Overview
Hotwire Multirate Symmetric Digital Subscriber Line (M/SDSL) and Multirate
High-bit-rate Digital Subscriber Line (M/HDSL) products maximize customer
service areas by varying the DSL line rate. This ensures symmetric DSL
connectivity over a wide range of telephone line distances and transmission line
qualities.
Hotwire M/SDSL products can transport data at full or fractional payload rates
over a 2-wire, full-duplex circuit over varying distances based on the conditions of
the 2-wire loop. Examples include support for router, multiplexer and PBX
connections on 24 gauge (.5 mm) cable at greater than 14,000 feet (4.6 km)
delivered at up to 2.048 Mbps (depending on model).
Hotwire M/HDSL products can transport at full or fractional payload rates over a
4-wire, full-duplex circuit over varying distances based on the conditions of the
4-wire loop. Examples include support for router, multiplexer and PBX
connections on 24 gauge (.5 mm) cable up to 21,000 feet (6.4 km) delivered at
up to 2.048 Mbps (depending on model).
Hotwire 79xx Standalone Termination Units are equipped with an automatic
configuration capability that reduces the installation process to a simple plug and
play mode. Simply connecting the units to the line automatically configures the
customer for the maximum data rate supported by the local loop. Units can also
be configured at fixed line speeds to achieve maximum distances.
About the Hotwire 79xx Standalone Termination Unit
1-2
7970-A2-GB20-00
August 1999
Hotwire 79xx Standalone Termination Unit Features
The Hotwire 79xx Standalone Termination Unit is an endpoint for the
chassis-mounted Hotwire 87xx Termination Unit housed in the Hotwire 8600
Series or 8800 Series Digital Subscriber Line Access Multiplexer (DSLAM).
Two Hotwire 79xx Standalone Termination Units can also be configured to
operate in a central office line termination unit (LTU) to customer premises
network termination unit (NTU) environment.
The termination unit offers these standard features:
H Embedded Operations Channel (EOC). Provides remote SNMP Traps,
Telnet session capability over the M/SDSL link, and download capabilities.
H Asynchronous Terminal Interface (ATI). Provides a menu-driven
VT100-compatible terminal interface for configuring and managing the
termination unit locally or remotely by Telnet session.
H Local Management (standalone unit). Provides local management using a:
Terminal or equivalent through the COM port of the unit
Network Management System (NMS) connection through the 10BaseT
port
Telnet through the COM port of the unit
H Remote Management (DSLAM card). Provides remote management using:
VT100-compatible Terminal or PC via the Management Serial port of the
DSLAM
NMS through the COM port or MCC port of the DSLAM
NMS through the 10BaseT port
Telnet over the EOC
SNMP or Telnet through the 10BaseT port or the Internal Management
Channel (IMC).
H Alarm Indication. Provides front panel status LEDs.
H Diagnostic Testing. Provides the capability to diagnose device and network
problems and perform digital loopbacks, pattern tests, and self-test.
H Device and Performance Monitoring. Provides the capability of tracking
and evaluating the unit’s operation, including health and status, and error-rate
monitoring.
H SNMP (Simple Network Management Protocol) Management. Provides
network management via an industry-standard SNMP management system.
About the Hotwire 79xx Standalone Termination Unit
1-3
7970-A2-GB20-00
August 1999
Network Configuration
Figure 1-1 shows a network application using a termination unit in a central office
(CO). In this configuration, a frame relay switch and a router are connected
through the termination unit to partner units supporting a host or router, and
frame relay encapsulated or unframed data. The figure also shows a
standalone-to-standalone configuration.
Frame
Relay
Switch
Router
T1 Host
(Frame Relay
Encapsulated
Data)
99-16486
Router
(Frame Relay
Encapsulated
Data)
Router
87xx Termination Unit
in DSLAM
CO Site
79xx
79xx
79xx
79xx 79xx
CP
NTU
CO Site
LTU
DSL
Customer Premises (CP)
DSL
DSL
G.703, DSX-1 or V.35
DSL
Figure 1-1. Sample Configurations
About the Hotwire 79xx Standalone Termination Unit
1-4
7970-A2-GB20-00
August 1999
Front Panel LED Status Indicators
Figures 1-2 through 1-4 show the front panel of the Hotwire 79xx Standalone
Termination Units. For more information on front panel LEDs, refer to Chapter 5,
Monitoring the Unit
.
POWER
ALARM
TEST
DSL
DSX-1
98-16116
7974 M/SDSL
TM
TM
Figure 1-2. Hotwire DSX-1 Interface Standalone Termination Unit Front Panel
POWER
ALARM
TEST
DSL
DTE
98-15856
7975 M/SDSL
TM
TM
Figure 1-3. Hotwire Synchronous Interface Standalone Termination Unit Front
Panel
POWER
ALARM
TEST
DSL
G.703
98-16003
7976 M/SDSL
TM
TM
Figure 1-4. Hotwire G.703 Interface Standalone Termination Unit Front Panel
About the Hotwire 79xx Standalone Termination Unit
1-5
7970-A2-GB20-00
August 1999
Rear Panel Interface Connections
Figures 1-5 through 1-7 show the physical interfaces of the termination units.
POWER DSLCOM DSX-1
98-16117
O
I
Figure 1-5. Hotwire 7974 and 7984 Standalone Termination Unit Rear Panel
POWER
DSLCOM
98-15880
PORT
O
I
Figure 1-6. Hotwire 7975 and 7985 Standalone Termination Unit Rear Panel
POWER DSLCOM
TX RX
G.703
75120
98-16005
O
I
Figure 1-7. Hotwire 7976 and 7986 Standalone Termination Unit Rear Panel
About the Hotwire 79xx Standalone Termination Unit
1-6
7970-A2-GB20-00
August 1999
SNMP Management Capabilities
The Hotwire 79xx Termination Units support SNMP Version 1, and can be
managed by any industry-standard SNMP manager and accessed using SNMP
by external SNMP managers.
Management Information Base (MIB) Support
For a detailed description of the supported MIBs, visit Paradyne’s Web site at
www.paradyne.com. Select
Service & Support
MIBs.
The following MIBs are supported:
H MIB II (RFC 1213 and RFC 1573) – Defines the general objects for use with
a network management protocol in TCP/IP internets and provides general
information about the unit. MIB II is backward-compatible with MIB I.
H DS1/E1 MIB (RFC 1406) – Models 7974, 7976, 7984, and 7986. Reports the
performance status of the DSX-1 or G.703 interface and supports the
features found on the DSX-1 or G.703 Performance Statistics screen.
H RS-232-Like MIB (RFC 1659) – Defines objects for managing RS-232-type
interfaces (e.g., V.35, RS-422, RS-423, etc.) and supports the synchronous
data port on the DSU.
H Entity MIB (RFC 2037) – Stores information about each device connected to
the DSLAM card. This enables the NMS to display graphical information
about each one of the endpoints.
H Paradyne Enterprise MIB – Supports configuration, status, statistics, and
tests.
H Generic Interface MIB Extensions (RFC 1229) — Models 7976 and 7986.
Supports control of tests on the E1 interface not supported by the previous
MIBs.
About the Hotwire 79xx Standalone Termination Unit
1-7
7970-A2-GB20-00
August 1999
SNMP Trap Support
Hotwire 79xx Standalone Termination Units support traps as defined in
RFC 1215.
Figure 1-8 illustrates a typical DSL SNMP configuration. Figure 1-9 illustrates an
DSL SNMP configuration connected directly to the Communications Port. Refer
to Chapter 9,
IP Addressing
and Appendix B,
Standards Compliance for SNMP
Traps
.
99-16487
DSLAM
Network
79xx
AC
INPUT
AC
48VDC CLASS 2 OR
LIMITED PWR SOURCE
RTN48V
AAB B
T5A
2
46
A
B
.
.
.
3
.
1
2
POSITION
STACK
ALM
A
IN
B
DC FUSES
T4A, MIN. 48V
5
DC PWR
FAN
OUT SERIAL
MCC 1
3
1
2
3
SYSTEM
OK
Alrm
Test
250V
SYSTEM
OK
Alrm
Test
1
2
3
4
G.703 ALRM
DSL PORT
LINK-UP
1
2
3
4
SYSTEM
OK
Alrm
Test
1
2
3
4
G.703 ALRM
DSL PORT
LINK-UP
SDSL
8715
1
2
3
4
Router
SNMP NMS
Ethernet
Interface
DSL
EOC
Data
Operation, Maintenance
and Provisioning Center
Ethernet
LAN
1
2
3
4
G.703 ALRM
DSL PORT
LINK-UP
1
2
3
4
87xx
Figure 1-8. DSL SNMP Configuration
99-16488
79xx
SNMP NMS
DSL
EOC
Router
Router
79xx
COM
Figure 1-9. DSL Local SNMP Configuration
About the Hotwire 79xx Standalone Termination Unit
1-8
7970-A2-GB20-00
August 1999
This page intentionally left blank.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165

Paradyne Hotwire 7976 User manual

Category
Networking
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI