Paradyne 9161 Single T1 Reference guide

AREA CODE CHANGE

Please note that the area code for

Paradyne Corporation in Largo, Florida

has changed from 813 to 727.

For any Paradyne telephone number that

appears in this manual with an 813 area

code, dial 727 instead.

MODEL 916x/926x

T1 ACCESS MUX

TECHNICAL REFERENCE

Document No. 9161-A2-GH30-20

September 1997

Printed on recycled paper

A

9161-A2-GH30-20

September 1997

Copyright  1997 Paradyne Corporation.

Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of this publication may be copied or distributed,

transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form

or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the

express written permission of Paradyne Corporation, 8545 126th Avenue North, P.O. Box 2826, Largo,

Florida 33779-2826.

Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically

disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation

reserves the right to revise this publication and to make changes from time to time in the contents hereof without

obligation of Paradyne Corporation to notify any person of such revision or changes.

Changes and enhancements to the product and to the information herein will be documented and issued as a new

release to this manual.

Warranty, Sales, and Service Information

Contact your sales or service representative directly for any help needed. For additional information concerning

warranty, sales, service, repair, installation, documentation, or training, use one of the following methods:

 Via the Internet: Visit the Paradyne World Wide Web site at http://www.paradyne.com

 Via Telephone: Call our automated call system to receive current information via fax or to speak with a

company representative.

— Within the U.S.A., call 1-800-870-2221

— International, call 813-530-2340

Trademarks

All products and services mentioned herein are the trademarks, service marks, registered trademarks or registered

service marks of their respective owners.

Important Regulatory Information

B

9161-A2-GH30-20 September 1997

EMI Warnings

!

WARNING:

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the requirements that no modifications will be

made to the equipment unless the changes or modifications are expressly approved by Paradyne.

!

WARNING:

To Users of Digital Apparatus in Canada:

This Class A digital apparatus meets all requirements of the Canadian interference-causing equipment

regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du règlement sur le matériel

brouilleur du Canada.

Important Regulatory Information

C

9161-A2-GH30-20

September 1997

Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product or included in the manual.

2. This product is intended to be used with a 3-wire grounding type plug – a plug which has a grounding pin. This is

a safety feature. Equipment grounding is vital to ensure safe operation. Do not defeat the purpose of the

grounding type plug by modifying the plug or using an adapter.

Prior to installation, use an outlet tester or a voltmeter to check the ac receptacle for the presence of earth

ground. If the receptacle is not properly grounded, the installation must not continue until a qualified electrician

has corrected the problem.

If a 3-wire grounding type power source is not available, consult a qualified electrician to determine another

method of grounding the equipment.

3. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to

protect it from overheating, these slots and openings must not be blocked or covered.

4. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the

power cord.

5. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous

high voltage points or other risks. Refer all servicing to qualified service personnel.

6. General purpose cables are provided with this product. Special cables, which may be required by the regulatory

inspection authority for the installation site, are the responsibility of the customer.

7. When installed in the final configuration, the product must comply with the applicable Safety Standards and

regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory

agencies and inspection authorities to ensure compliance.

8. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If

products installed in separate buildings are interconnected, the voltage potential may cause a hazardous

condition. Consult a qualified electrical consultant to determine whether or not this phenomenon exists and, if

necessary, implement corrective action prior to interconnecting the products.

9. In addition, if the equipment is to be used with telecommunications circuits, take the following precautions:

— Never install telephone wiring during a lightning storm.

— Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

— Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the

network interface.

— Use caution when installing or modifying telephone lines.

— Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of

electric shock from lightning.

— Do not use the telephone to report a gas leak in the vicinity of the leak.

i

9161-A2-GH30-20

September 1997

Contents

About This Guide

 Document Purpose and Intended Audience ix. . . . . . . . . . . . . . . . . . . . . . . . .

 Document Summary ix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Conventions Used x. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Product-Related Documents xi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Reference Documents xii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 About the T1 Access Mux

 Overview 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Components 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Features 1-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 Management and IP Addressing

 Overview 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Configuring Local Management Control 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Creating a Management Link Through the COM Port 2-2. . . . . . . . . . . . .

Configuring an External Device (Connected to the COM Port) 2-3. . . . .

 Configuring End-to-End Management Control 2-4. . . . . . . . . . . . . . . . . . . . . . .

Management Control Using the ESF FDL 2-4. . . . . . . . . . . . . . . . . . . . . . .

Management Control Using an EDL 2-5. . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Selecting an IP Addressing Scheme 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 IP Addressing Scheme Examples 2-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Direct Management Links to Remote T1 Access Units 2-7. . . . . . . . . . . .

Routing to Remote T1 Access Units on the Same Subnet 2-8. . . . . . . . .

Routing to Remote Access Units Using Different Subnets 2-9. . . . . . . . .

Routing to Remote T1 Access Units Using Routers 2-10. . . . . . . . . . . . . .

Assigning IP Addresses and Subnet Masks 2-11. . . . . . . . . . . . . . . . . . . . .

Contents

ii

9161-A2-GH30-20

September 1997

3 Applications

 Overview 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 T1 Access Unit with High Speed Data 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 T1 Access Unit with High Speed Data and E&M 3-3. . . . . . . . . . . . . . . . . . . . .

 T1 Access Unit with High Speed Data and APL 3-4. . . . . . . . . . . . . . . . . . . . .

 T1 Access Unit with High Speed Data, FXS and E&M 3-5. . . . . . . . . . . . . . . .

 T1 Access Unit with High Speed Data and Drop & Insert 3-6. . . . . . . . . . . . .

 Channel Bank Replacement and Additions 3-7. . . . . . . . . . . . . . . . . . . . . . . . .

 Off-Premises Extension (OPX) 3-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Direct Inward Dial (DID) 3-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 Setting Up

 Considerations When Setting Up 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Selecting a Management Interface 4-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Logins 4-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Adding System Identity Information 4-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Setting Date and Time 4-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Configuring the T1 Access Unit 4-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Recommended Order of Configuration 4-5. . . . . . . . . . . . . . . . . . . . . . . . .

Configuration Option Areas 4-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Accessing and Displaying Configuration Options 4-5. . . . . . . . . . . . . . . .

Changing Configuration Options 4-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Saving Configuration Options 4-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Configuring T1 and DSX-1 Interfaces 4-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring the Network Interface 4-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring the DSX-1 Interface 4-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Configuring Ports 4-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring Sync Data Ports 4-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring Voice Ports 4-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Copying Port Configurations 4-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Assigning Cross Connections 4-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Assigning DSX-1 Timeslots to the Network Interface 4-36. . . . . . . . . . . . .

DSX-1 Signaling Assignments and Trunk Conditioning 4-37. . . . . . . . . . .

Assigning Network 2 Timeslots to Network 1 Interface Timeslots 4-40. . .

Network to Network Signaling Assignments and

Trunk Conditioning 4-40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Assigning Voice Ports to DSX-1 or Network Interface Timeslots 4-41. . . .

Assigning Sync Data Ports 4-41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Clearing Port Assignments 4-43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents

iii

9161-A2-GH30-20

September 1997

 Setting System Options 4-44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Setting User Interface Options 4-48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setting Up the Communication Port 4-48. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setting Up the Communication Port to Support an

External Device 4-53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setting Up to Support a Telnet or FTP Session 4-57. . . . . . . . . . . . . . . . . .

 Configuring for Alarms and Traps 4-60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Setting Management and Communication Options 4-63. . . . . . . . . . . . . . . . . .

Setting Communication Protocol 4-63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setting Up for SNMP Management 4-66. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setting Up SNMP NMS Security 4-68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setting Up for SNMP Traps 4-70. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Setting Up and Placing a Call 4-74. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 Troubleshooting and Maintenance

 What Are the Troubleshooting and Maintenance Features? 5-1. . . . . . . . . . .

 How Do I Know There Is a Problem? 5-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 LEDs 5-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Alarms 5-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Viewing Alarm Messages 5-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Automatic Dialing Out When an Alarm Occurs 5-3. . . . . . . . . . . . . . . . . . .

Manual Dialing Out When an Alarm Occurs 5-4. . . . . . . . . . . . . . . . . . . . .

Displaying Directory Numbers 5-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Changing Directory Numbers 5-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Changing Device Name 5-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Supported SNMP Traps 5-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Dialing Out and Sending SNMP Traps 5-6. . . . . . . . . . . . . . . . . . . . . . . . . .

 Troubleshooting 5-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Test Jacks 5-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9161 Single T1 NAM Test Jack Functions 5-10. . . . . . . . . . . . . . . . . . . . . . .

9261 Dual T1 NAM Test Jack Functions 5-11. . . . . . . . . . . . . . . . . . . . . . . .

9109 Dual DSX APM Test Jack Functions 5-12. . . . . . . . . . . . . . . . . . . . . .

 Resetting the T1 Access Unit 5-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Resetting the T1 Access Unit from the Control Menu 5-13. . . . . . . . . . . . .

Restoring Access to the User Interface 5-13. . . . . . . . . . . . . . . . . . . . . . . . .

Contents

iv

9161-A2-GH30-20

September 1997

 Tests Available 5-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Interface Tests 5-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Line Loopback 5-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Payload Loopback 5-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Repeater Loopback 5-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Remote Loopbacks 5-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sending and Monitoring Pattern Tests 5-21. . . . . . . . . . . . . . . . . . . . . . . . . .

 Data Port Tests 5-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DTE Loopback (DTLB) 5-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DTE Payload Loopback (DTPLB) 5-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Data Channel Loopback (DCLB) 5-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

V.54 Remote Loopback 5-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Remote FT1 Data Channel Loopback 5-25. . . . . . . . . . . . . . . . . . . . . . . . . .

Sending and Monitoring Pattern Tests 5-25. . . . . . . . . . . . . . . . . . . . . . . . . .

 Voice Port Tests 5-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Digital Loopbacks 5-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Analog Loopbacks 5-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Line Loopbacks 5-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Test Tones 5-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Force and Monitor Signaling 5-29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Device Tests 5-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Test Timeout 5-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Starting and Stopping a Test 5-32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Aborting All Tests 5-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Determining Test Status and Results 5-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Hot Swapping of APMs 5-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

APM Insertion 5-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

APM Removal 5-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 NAM Removal 5-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Downloading Software 5-35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 File Transfer 5-35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Performing an Upgrade 5-36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Backing Up Your Configuration 5-37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents

v

9161-A2-GH30-20

September 1997

6 Security

 Creating a Login 6-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Deleting a Login 6-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Limiting Access 6-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Limiting Async Terminal Direct Access 6-3. . . . . . . . . . . . . . . . . . . . . . . . . .

Limiting Telnet Access 6-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Controlling External Device Access 6-6. . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Controlling SNMP Access 6-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disabling SNMP Access 6-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Assigning SNMP Community Names and Access Levels 6-8. . . . . . . . .

Limiting SNMP Access Through IP Addresses 6-9. . . . . . . . . . . . . . . . . .

A Menus and Configuration Worksheets

 Menus A-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Recording Configurations A-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Channel Assignments Worksheets A-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

B MIB Descriptions

 MIB II Descriptions, RFC 1213 B-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

System Group B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Interfaces Group B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Interface Stack Group B-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Interface Test Table B-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Generic Receive Address Table B-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

IP Group B-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ICMP Group B-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TCP Group B-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

UDP Group B-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Transmission Group B-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SNMP Group B-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 DS1/E1 MIB Descriptions, RFC 1406 B-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Near End Group, DS1/E1 MIB B-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DS1 Configuration Table B-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DS1 Current Table (dsx1CurrentEntry) B-22. . . . . . . . . . . . . . . . . . . . . . . . .

DS1 Interval Table (dsx1IntervalEntry) B-23. . . . . . . . . . . . . . . . . . . . . . . . .

DS1 Total Table (dsx1TotalEntry) B-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Far End Group, DS1/E1 MIB B-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DS1 Fractional Group, DS1/E1 MIB B-24. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents

vi

9161-A2-GH30-20

September 1997

 RS-232-Like MIB, RFC 1659 B-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General Port Table, RS-232-Like MIB B-25. . . . . . . . . . . . . . . . . . . . . . . . . .

Asynchronous Port Table B-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Synchronous Port Table B-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input Signal Table B-29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output Signal Table B-29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Enterprise MIB B-30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Device Configuration Variable B-30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Port Usage Table, attp-devPortUsage.

PortUsage, (attp-interfaces 3) B-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Voice Interface Specific Definitions, voice, (attp-interfaces 4) B-31. . . . . .

DS1 Interface Configuration Table, ent-ds1, (attp-interfaces 5) B-31. . . . .

DS1 Performance Statistics Group, DS1PerfStats, (ent-ds4) B-31. . . . . .

Synchronous Data Port Configuration, syncPort, (attp-interfaces 6) B-31

EDL Near-end and Far-end Registers, dataPortPerStats,

(syncPort 4) B-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Channel Configuration, crossConnect, (attp-interfaces 7) B-31. . . . . . . . .

Device Security, attp-security, (attp-common 8) B-32. . . . . . . . . . . . . . . . . .

Device Traps, attp-traps, (attp-common 9) B-32. . . . . . . . . . . . . . . . . . . . . .

Device Control, attp-control, (attp-common 10) B-32. . . . . . . . . . . . . . . . . .

Device Health and Status, devStatus (attp-devStatus) B-32. . . . . . . . . . . .

C SNMP Traps

 Trap: warmStart C-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Trap: authentificationFailure C-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Traps: linkUp and linkDown C-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Traps: Enterprise-Specific C-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

D SNMP Cross-Reference

Contents

vii

9161-A2-GH30-20

September 1997

E Cables, Connectors, and Pin Assignments

 COM Port E-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

COM Port-to-PC Cable E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

COM Port-to-Terminal/Printer Cable E-2. . . . . . . . . . . . . . . . . . . . . . . . . . .

COM Port-to-External Device Cable E-3. . . . . . . . . . . . . . . . . . . . . . . . . . .

Gender Adapter/Changer E-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LAN Adapter and Cables E-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 T1 Network Interface Cable E-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 DSX-1 Port Interface E-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 T1 Line Interface Cable E-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 EIA-530A Port Interface E-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

EIA-530A-to-V.35 DTE Adapter Cable E-7. . . . . . . . . . . . . . . . . . . . . . . . . .

EIA-530A-to-RS449 DTE Adapter Cable E-9. . . . . . . . . . . . . . . . . . . . . . . .

EIA-530A-to-X.21 DTE Adapter Cable E-11. . . . . . . . . . . . . . . . . . . . . . . . . .

 Voice APM Cables E-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FXO/FXS Voice APM Connector E-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

E&M Voice APM Connector E-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Extension Cables E-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

F Technical Specifications

G Equipment List

Glossary

Index

ix

9161-A2-GH30-20

September 1997

About This Guide

Document Purpose and Intended Audience

This manual contains information needed to properly set up, configure and verify

operation of the 916x/926x T1 Access Mux. It is designed for system designers,

engineers, system administrators, and operators.

Document Summary

Section Description

Chapter 1

About the T1 Access Mux.

Provides an overview of the

components and features of the T1 access unit.

Chapter 2

Management and IP Addressing.

Contains the steps

you need to provide management connectivity to the

T1 access unit, including an IP addressing scheme.

Chapter 3

Applications.

Shows some typical T1 access unit

applications.

Chapter 4

Setting Up.

Describes how to configure the T1 access

unit for operation in your network.

Chapter 5

Troubleshooting and Maintenance.

Explains

troubleshooting and test procedures of the T1 access

unit. Also includes dial-out procedures, hot swapping of

APMs, and how to perform a software upgrade.

Chapter 6

Security.

Describes how to administer security,

including log-in procedures, and limiting user interface,

telnet, and SNMP access.

Appendix A

Menus and Configuration Worksheets.

Contains a

graphical representation of the system configuration

options and worksheets for you to record your

selections.

Appendix B

MIB Descriptions.

Clarifies MIB object descriptions for

the T1 access unit.

About This Guide

x

9161-A2-GH30-20

September 1997

Section Description

Appendix C

SNMP Traps.

Lists SNMP traps.

Appendix D

SNMP Cross-Reference.

Provides a cross-reference of

SNMP MIB objects and user interface commands.

Appendix E

Cables, Connectors, and Pin Assignments.

Describes

cables to be used with the T1 access unit, as well as

their connectors and pin assignments.

Appendix F

Technical Specifications.

Appendix G

Equipment List.

Lists related equipment.

Glossary Defines acronyms and terms used in this document.

Index Lists key terms, acronyms, concepts, and sections in

alphabetical order.

Conventions Used

Convention Indicates

Italic

Variable information (e.g., slot

s

,

indicating slot

number 01, 02, etc.)

.

Menu selection sequence:

The selections to be made from a menu or

selections from within a menu before

performing a procedural step (e.g.,

Main Menu

→

Status

→

System and Test Status

).

Brackets [ ] Multiple selection choices (e.g., [

Current

Configuration/Customer Configuration 1/

Customer Configuration 2

]).

About This Guide

xi

9161-A2-GH30-20

September 1997

Product-Related Documents

Document Number Document Title

9000-A2-GN14

2-Slot and 5-Slot Housing Wall-Mounting Kit

Installation Instructions

9000-A2-GN15

2-Slot Housing Installation Instructions

9000-A2-GN16

5-Slot Housing with AC Power Supply Installation

Instructions

9000-A2-GN17

5-Slot Power Supply Installation Instructions

9000-A2-GN1A

2-Slot Power Supply Installation Instructions

9000-A2-GN1B

DC Power Supply For 5-Slot Housing Installation

Instructions

9000-A2-GN1C

5-Slot Housing with DC Power Supply Installation

Instructions

9000-A2-GX41

91xx Series T1 Equipment Safety, Regulatory,

Warranty and Service Information

9000-A2-GX42

Affidavit Requirements for Connection to Digital

Service

9109-A2-GN10

9109 Sync Data Application Module (APM)

Installation Instructions

9109-A2-GN11

9109 E&M Analog Voice Application Module (APM)

Installation Instructions

9109-A2-GN12

9109 FXS Analog Voice Application Module (APM)

Installation Instructions

9109-A2-GN13

9109 Dual DSX Application Module (APM)

Installation Instructions

9109-A2-GN14

9109 FXO Analog Voice Application Module (APM)

Installation Instructions

9161-A2-GB20

Model 916x/926x T1 Access Mux User’s Guide

9161-A2-GK41

916x T1 Access Mux Software Release 1 to

Software Release 2 Upgrade Instructions

9161-A2-GN10

9161 Single T1 Network Access Module (NAM)

Installation Instructions

9261-A2-GN10

9261 Dual T1 Network Access Module (NAM)

Installation Instructions

9261-A2-GZ10

9161 Single T1 Network Access Module (NAM) to

9261 Dual T1 NAM Upgrade Instructions

Call your sales representative to order additional product documentation.

About This Guide

xii

9161-A2-GH30-20

September 1997

Reference Documents

CSA-22.2 No. 950

CSA 108-M1983

FCC Part 15

UL 1950

Management Information Base for Network Management of TCP/IP-Based

Internets

:

MIBII

. RFC 1213, March 1991

Definitions of Managed Objects for the DS1 and E1 Interface Types

. RFC 1406,

January 1993

Evolution of the-Interfaces Group of MIB II

. RFC 1573, January 1994

Definitions of Managed Objects for RS-232-like Hardware Devices

. RFC 1659,

July 1994

1-1

9161-A2-GH30-20

September 1997

About the T1 Access Mux

1

Overview

The T1 Access Mux is the interface between your customer premises equipment

and a T1 network. The 916x/926x product line supports the following T1 Access

Mux configurations:

 9161 Single T1 NAM or 9261 Dual T1 NAM in a 2-slot housing

 9161 Single T1 NAM or 9261 Dual T1 NAM in a 5-slot housing

Housing

g

T1 NAM

2-Slot Housing 5-Slot Housing

9161 Single T1 NAM Model 9162 Model 9165

9261 Dual T1 NAM Model 9262 Model 9265

All configurations are referred to as the T1 access unit in this document.

About the T1 Access Mux

1-2

9161-A2-GH30-20

September 1997

Components

The T1 access unit consists of either a 9161 or 9261 Network Access Module

(NAM) installed in a two-slot or five-slot chassis, along with optional Sync Data,

DSX, or voice Application Modules (APMs) for particular applications.

496-1512

9

Front View

(without Bezel)

Rear View

Slot 01 Slot 02 Slot 01Slot 02

Fully Loaded 2-Slot Housing

2–OK

OK

ALM

TST

BKP

SIG

OOF

ALM

SIG

OOF

ALM

1–OK

9161

IN

OUT

IN

OUT

IN

OUT

IN

OUT

NET DSX NET MON DSX MON

NETWORK DSX PORT

496-1520

6

2–OK

OK

ALM

TST

BKP

SIG

OOF

ALM

SIG

OOF

ALM

1–OK

9261

IN

OUT

IN

OUT

IN

OUT

IN

OUT

NET1 NET2 NET1 MON NET2 MON

NET 1 NET 2 PORT

97-15645

About the T1 Access Mux

1-3

9161-A2-GH30-20

September 1997

496-1513

8

Front View (without Bezel)

Rear View

Slot 01

Slot 05

Slot 01

Slot 05

Fully Loaded 5-Slot Housing

The 9161 Single T1 NAM is equipped with:

 One T1 network interface

 One DSX-1 drop and insert port

 Two DTE interface ports

The 9261 Dual T1 NAM is equipped with:

 Two T1 network interfaces

 Two DTE interface ports

OK

SIG

OOF

ALM

SIG

OOF

ALM

9109 DSX

IN

OUT

IN

OUT

IN

OUT

IN

OUT

DSX 1 DSX 2 DSX 1 MON DSX 2 MON

DSX 1 DSX 2

97-15649

OK

9109 SYNC DATA

1–OK

PORT

2–OK

3–OK

4–OK

496-1515

4

OK

9109 E&M

496-1514

1

OK

9109 FXO

97-15648

OK

9109 FXS

496-1513

9

About the T1 Access Mux

1-4

9161-A2-GH30-20

September 1997

There are five APM types:

 The Synchronous Data APM, which supports:

— Four ports, each supporting EIA-530A, V.35,

RS449, or V.11/X.21

— Rates of Nx56 or Nx64

— Standard RS232-like (RFC 1659) MIB

— Enterprise MIB for testing, statistics, and

some configuration functions

See the

9109 Sync Data Application Module (APM)

Installation Instructions

for more information.

 The Dual DSX APM, which supports:

— Two DSX-1 drop and insert ports

See the

9109 Dual DSX Application Module

(APM) Installation Instructions

for more

information.

 The E&M Voice APM, which supports:

— E&M Type I, II, IV, or V circuits

— law PCM coding of analog voice line

— Enterprise MIB for testing and

some configuration functions

See the

9109 E&M Analog Voice

Application Module (APM) Installation

Instructions

for more information.

 The FXO Voice APM, which supports:

— FXO circuits

— law PCM coding of analog voice line

— Enterprise MIB for testing and some

configuration functions

See the

9109 FXO Analog Voice Application

Module (APM) Installation Instructions

for more information.

 The FXS Voice APM, which supports:

— FXS circuits

— law PCM coding of analog voice line

— Enterprise MIB for testing and some

configuration functions

See the

9109 FXS Analog Voice Application Module (APM) Installation

Instructions

for more information.

Page is loading ...

Paradyne 9161 Single T1, 9261 Reference guide

Related papers

Other documents