Stagg SMS15DP760 User manual
- Category
- Supplementary music equipment
- Type
- User manual
Stagg SMS15DP760 is a 2-Way powered loudspeaker with a recommended fuse amperage of 7.5A. This manual provides instructions on safety precautions, how to prevent risk of fire, and how to fuse the unit to prevent damage. The loudspeaker uses a 15" woofer with a 75mm voice coil and 1.75" titanium compression driver with a 25mm voice coil, for a frequency response from 45Hz-18KHz +-3dB. This loudspeaker includes protections for over-current, temperature, and RMS.
Stagg SMS15DP760 is a 2-Way powered loudspeaker with a recommended fuse amperage of 7.5A. This manual provides instructions on safety precautions, how to prevent risk of fire, and how to fuse the unit to prevent damage. The loudspeaker uses a 15" woofer with a 75mm voice coil and 1.75" titanium compression driver with a 25mm voice coil, for a frequency response from 45Hz-18KHz +-3dB. This loudspeaker includes protections for over-current, temperature, and RMS.
2
3
1
The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even
under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or
death.
The symbol is used in the service documentation to indicate that specific component shall be replaced
only by the component specified in that documentation for safety reasons.
Protective grounding terminal
Alternating current/voltage
Hazardous live terminal
ON: Denotes the apparatus is turned on
OFF: Denotes the apparatus is turned off.
WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the operator.
CAUTION: Describes precautions that should be observed to prevent danger of the apparatus.
1. IMPORTANT SAFETY INSTRUCTIONS
·Read these instructions.
·Keep these instructions.
·Heed all warning.
·Follow all instructions.
Water & Moisture
·
The apparatus should be protected from moisture and
rain, can not used near water, for example: near bath-
tub, kitchen sink or a swimming pool, etc.
·Heat
The apparatus should be located away from the heat
source such as radiators, stoves or other appliances
that produce heat.
·Ventilation
Do not block areas of ventilation opening. Failure to
do could result in fire. Always install accordance with
the manufacturer's instructions.
·Object and Liquid Entry
Objects do not fall into and liquids are not spilled into
the inside of the apparatus for safety.
·Power Cord and Plug
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet, refer
to electrician for replacement.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY SYMBOLS
°
·Power Supply
The apparatus should be connected to the power supply
only of the type as marked on the apparatus or described
in the manual. Failure to do could result in damage to the
product and possibly the user.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Where the MAINS plug or an appliance coupler is used as
the disconnect device, the disconnect device shall remain
readily operable.
·Fuse
To prevent the risk of fire and damaging the unit, please
use only of the recommended fuse type as described in
the manual. Before replacing the fuse, make sure the unit
turned off and disconnected from the AC outlet.
·Electrical Connection
Improper electrical wiring may invalidate the product war-
ranty.
·Cleaning
Clean only with a dry cloth. Do not use any solvents such
as benzol or alcohol.
·Servicing
Do not implement any servicing other than those means
described in the manual. Refer all servicing to qualified
service personnel only.
·Only use accessories/attachments or parts recommended
by the manufacturer.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Owner`s Manual
TECHNICAL SPECIFICATIONS
MODEL
POWER TYPE
POWER(RMS)
IMPED(ohm)
TWEETER
WOOFER
FREQUENCY
SENSITIVITY
(1w@1m)
Mp3
GROSSWEIGHT
(Kg)
PACKAGE
(HXWXD) (Mm)
SMS12DP700
SMS12DP700LCD
SMS12DP700
SMS12DP760LCD
300W+70W 300W+70W 300W+75W 300W+75W
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
8 8 8 8
1.35 "
34mm Ti dome drive
1.75 "
44mm Ti dome drive
1.75 "
44mm Ti dome drive
1.35 "
34mm Ti dome drive
12 "(75mm voice coil/
50 oz magnet)
12"(65mm voice coil/
50 oz magnet)
15"(75mm voice coil/
60 oz magnet)
15"(75mm voice coil/
60 oz magnet)
45Hz-18KHz 45Hz-18KHz 45Hz-18KHz 45Hz-18KHz
98db 98db 98db 98db
NO YES NO YES
21 2117.517.5
760X490X425 760X490X425625X435X380625X435X380
10
1
The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even
under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or
death.
The symbol is used in the service documentation to indicate that specific component shall be replaced
only by the component specified in that documentation for safety reasons.
Protective grounding terminal
Alternating current/voltage
Hazardous live terminal
ON: Denotes the apparatus is turned on
OFF: Denotes the apparatus is turned off.
WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the operator.
CAUTION: Describes precautions that should be observed to prevent danger of the apparatus.
1. IMPORTANT SAFETY INSTRUCTIONS
·Read these instructions.
·Keep these instructions.
·Heed all warning.
·Follow all instructions.
Water & Moisture
·
The apparatus should be protected from moisture and
rain, can not used near water, for example: near bath-
tub, kitchen sink or a swimming pool, etc.
·Heat
The apparatus should be located away from the heat
source such as radiators, stoves or other appliances
that produce heat.
·Ventilation
Do not block areas of ventilation opening. Failure to
do could result in fire. Always install accordance with
the manufacturer's instructions.
·Object and Liquid Entry
Objects do not fall into and liquids are not spilled into
the inside of the apparatus for safety.
·Power Cord and Plug
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet, refer
to electrician for replacement.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY SYMBOLS
°
·Power Supply
The apparatus should be connected to the power supply
only of the type as marked on the apparatus or described
in the manual. Failure to do could result in damage to the
product and possibly the user.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Where the MAINS plug or an appliance coupler is used as
the disconnect device, the disconnect device shall remain
readily operable.
·Fuse
To prevent the risk of fire and damaging the unit, please
use only of the recommended fuse type as described in
the manual. Before replacing the fuse, make sure the unit
turned off and disconnected from the AC outlet.
·Electrical Connection
Improper electrical wiring may invalidate the product war-
ranty.
·Cleaning
Clean only with a dry cloth. Do not use any solvents such
as benzol or alcohol.
·Servicing
Do not implement any servicing other than those means
described in the manual. Refer all servicing to qualified
service personnel only.
·Only use accessories/attachments or parts recommended
by the manufacturer.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Owner`s Manual
TECHNICAL SPECIFICATIONS
MODEL
POWER TYPE
POWER(RMS)
IMPED(ohm)
TWEETER
WOOFER
FREQUENCY
SENSITIVITY
(1w@1m)
Mp3
GROSSWEIGHT
(Kg)
PACKAGE
(HXWXD) (Mm)
SMS12DP700
SMS12DP700LCD
SMS12DP700
SMS12DP760LCD
300W+70W 300W+70W 300W+75W 300W+75W
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
8 8 8 8
1.35 "
34mm Ti dome drive
1.75 "
44mm Ti dome drive
1.75 "
44mm Ti dome drive
1.35 "
34mm Ti dome drive
12 "(75mm voice coil/
50 oz magnet)
12"(65mm voice coil/
50 oz magnet)
15"(75mm voice coil/
60 oz magnet)
15"(75mm voice coil/
60 oz magnet)
45Hz-18KHz 45Hz-18KHz 45Hz-18KHz 45Hz-18KHz
98db 98db 98db 98db
NO YES NO YES
21 2117.517.5
760X490X425 760X490X425625X435X380625X435X380
10
1
The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even
under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or
death.
The symbol is used in the service documentation to indicate that specific component shall be replaced
only by the component specified in that documentation for safety reasons.
Protective grounding terminal
Alternating current/voltage
Hazardous live terminal
ON: Denotes the apparatus is turned on
OFF: Denotes the apparatus is turned off.
WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the operator.
CAUTION: Describes precautions that should be observed to prevent danger of the apparatus.
1. IMPORTANT SAFETY INSTRUCTIONS
·Read these instructions.
·Keep these instructions.
·Heed all warning.
·Follow all instructions.
Water & Moisture
·
The apparatus should be protected from moisture and
rain, can not used near water, for example: near bath-
tub, kitchen sink or a swimming pool, etc.
·Heat
The apparatus should be located away from the heat
source such as radiators, stoves or other appliances
that produce heat.
·Ventilation
Do not block areas of ventilation opening. Failure to
do could result in fire. Always install accordance with
the manufacturer's instructions.
·Object and Liquid Entry
Objects do not fall into and liquids are not spilled into
the inside of the apparatus for safety.
·Power Cord and Plug
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet, refer
to electrician for replacement.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY SYMBOLS
°
·Power Supply
The apparatus should be connected to the power supply
only of the type as marked on the apparatus or described
in the manual. Failure to do could result in damage to the
product and possibly the user.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Where the MAINS plug or an appliance coupler is used as
the disconnect device, the disconnect device shall remain
readily operable.
·Fuse
To prevent the risk of fire and damaging the unit, please
use only of the recommended fuse type as described in
the manual. Before replacing the fuse, make sure the unit
turned off and disconnected from the AC outlet.
·Electrical Connection
Improper electrical wiring may invalidate the product war-
ranty.
·Cleaning
Clean only with a dry cloth. Do not use any solvents such
as benzol or alcohol.
·Servicing
Do not implement any servicing other than those means
described in the manual. Refer all servicing to qualified
service personnel only.
·Only use accessories/attachments or parts recommended
by the manufacturer.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Owner`s Manual
TECHNICAL SPECIFICATIONS
MODEL
POWER TYPE
POWER(RMS)
IMPED(ohm)
TWEETER
WOOFER
FREQUENCY
SENSITIVITY
(1w@1m)
Mp3
GROSSWEIGHT
(Kg)
PACKAGE
(HXWXD) (Mm)
SMS12DP700
SMS12DP700LCD
SMS12DP700
SMS12DP760LCD
300W+70W 300W+70W 300W+75W 300W+75W
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
8 8 8 8
1.35 "
34mm Ti dome drive
1.75 "
44mm Ti dome drive
1.75 "
44mm Ti dome drive
1.35 "
34mm Ti dome drive
12 "(75mm voice coil/
50 oz magnet)
12"(65mm voice coil/
50 oz magnet)
15"(75mm voice coil/
60 oz magnet)
15"(75mm voice coil/
60 oz magnet)
45Hz-18KHz 45Hz-18KHz 45Hz-18KHz 45Hz-18KHz
98db 98db 98db 98db
NO YES NO YES
21 2117.517.5
760X490X425 760X490X425625X435X380625X435X380
10
1
The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even
under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or
death.
The symbol is used in the service documentation to indicate that specific component shall be replaced
only by the component specified in that documentation for safety reasons.
Protective grounding terminal
Alternating current/voltage
Hazardous live terminal
ON: Denotes the apparatus is turned on
OFF: Denotes the apparatus is turned off.
WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the operator.
CAUTION: Describes precautions that should be observed to prevent danger of the apparatus.
1. IMPORTANT SAFETY INSTRUCTIONS
·Read these instructions.
·Keep these instructions.
·Heed all warning.
·Follow all instructions.
Water & Moisture
·
The apparatus should be protected from moisture and
rain, can not used near water, for example: near bath-
tub, kitchen sink or a swimming pool, etc.
·Heat
The apparatus should be located away from the heat
source such as radiators, stoves or other appliances
that produce heat.
·Ventilation
Do not block areas of ventilation opening. Failure to
do could result in fire. Always install accordance with
the manufacturer's instructions.
·Object and Liquid Entry
Objects do not fall into and liquids are not spilled into
the inside of the apparatus for safety.
·Power Cord and Plug
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet, refer
to electrician for replacement.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY SYMBOLS
°
·Power Supply
The apparatus should be connected to the power supply
only of the type as marked on the apparatus or described
in the manual. Failure to do could result in damage to the
product and possibly the user.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Where the MAINS plug or an appliance coupler is used as
the disconnect device, the disconnect device shall remain
readily operable.
·Fuse
To prevent the risk of fire and damaging the unit, please
use only of the recommended fuse type as described in
the manual. Before replacing the fuse, make sure the unit
turned off and disconnected from the AC outlet.
·Electrical Connection
Improper electrical wiring may invalidate the product war-
ranty.
·Cleaning
Clean only with a dry cloth. Do not use any solvents such
as benzol or alcohol.
·Servicing
Do not implement any servicing other than those means
described in the manual. Refer all servicing to qualified
service personnel only.
·Only use accessories/attachments or parts recommended
by the manufacturer.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Owner`s Manual
TECHNICAL SPECIFICATIONS
MODEL
POWER TYPE
POWER(RMS)
IMPED(ohm)
TWEETER
WOOFER
FREQUENCY
SENSITIVITY
(1w@1m)
Mp3
GROSSWEIGHT
(Kg)
PACKAGE
(HXWXD) (Mm)
SMS12DP700
SMS12DP700LCD
SMS12DP700
SMS12DP760LCD
300W+70W 300W+70W 300W+75W 300W+75W
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
8 8 8 8
1.35 "
34mm Ti dome drive
1.75 "
44mm Ti dome drive
1.75 "
44mm Ti dome drive
1.35 "
34mm Ti dome drive
12 "(75mm voice coil/
50 oz magnet)
12"(65mm voice coil/
50 oz magnet)
15"(75mm voice coil/
60 oz magnet)
15"(75mm voice coil/
60 oz magnet)
45Hz-18KHz 45Hz-18KHz 45Hz-18KHz 45Hz-18KHz
98db 98db 98db 98db
NO YES NO YES
21 2117.517.5
760X490X425 760X490X425625X435X380625X435X380
10
1
The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even
under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or
death.
The symbol is used in the service documentation to indicate that specific component shall be replaced
only by the component specified in that documentation for safety reasons.
Protective grounding terminal
Alternating current/voltage
Hazardous live terminal
ON: Denotes the apparatus is turned on
OFF: Denotes the apparatus is turned off.
WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the operator.
CAUTION: Describes precautions that should be observed to prevent danger of the apparatus.
1. IMPORTANT SAFETY INSTRUCTIONS
·Read these instructions.
·Keep these instructions.
·Heed all warning.
·Follow all instructions.
Water & Moisture
·
The apparatus should be protected from moisture and
rain, can not used near water, for example: near bath-
tub, kitchen sink or a swimming pool, etc.
·Heat
The apparatus should be located away from the heat
source such as radiators, stoves or other appliances
that produce heat.
·Ventilation
Do not block areas of ventilation opening. Failure to
do could result in fire. Always install accordance with
the manufacturer's instructions.
·Object and Liquid Entry
Objects do not fall into and liquids are not spilled into
the inside of the apparatus for safety.
·Power Cord and Plug
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet, refer
to electrician for replacement.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY SYMBOLS
°
·Power Supply
The apparatus should be connected to the power supply
only of the type as marked on the apparatus or described
in the manual. Failure to do could result in damage to the
product and possibly the user.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Where the MAINS plug or an appliance coupler is used as
the disconnect device, the disconnect device shall remain
readily operable.
·Fuse
To prevent the risk of fire and damaging the unit, please
use only of the recommended fuse type as described in
the manual. Before replacing the fuse, make sure the unit
turned off and disconnected from the AC outlet.
·Electrical Connection
Improper electrical wiring may invalidate the product war-
ranty.
·Cleaning
Clean only with a dry cloth. Do not use any solvents such
as benzol or alcohol.
·Servicing
Do not implement any servicing other than those means
described in the manual. Refer all servicing to qualified
service personnel only.
·Only use accessories/attachments or parts recommended
by the manufacturer.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Owner`s Manual
TECHNICAL SPECIFICATIONS
MODEL
POWER TYPE
POWER(RMS)
IMPED(ohm)
TWEETER
WOOFER
FREQUENCY
SENSITIVITY
(1w@1m)
Mp3
GROSSWEIGHT
(Kg)
PACKAGE
(HXWXD) (Mm)
SMS12DP700
SMS12DP700LCD
SMS12DP700
SMS12DP760LCD
300W+70W 300W+70W 300W+75W 300W+75W
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
Bi-Amplified
CLASS D
8 8 8 8
1.35 "
34mm Ti dome drive
1.75 "
44mm Ti dome drive
1.75 "
44mm Ti dome drive
1.35 "
34mm Ti dome drive
12 "(75mm voice coil/
50 oz magnet)
12"(65mm voice coil/
50 oz magnet)
15"(75mm voice coil/
60 oz magnet)
15"(75mm voice coil/
60 oz magnet)
45Hz-18KHz 45Hz-18KHz 45Hz-18KHz 45Hz-18KHz
98db 98db 98db 98db
NO YES NO YES
21 2117.517.5
760X490X425 760X490X425625X435X380625X435X380
10
4
Introduction
Congratulations and thank you for purchasing the stagg SMSDP700 Series
professional sound reinforcement loudspeaker.
This loudspeaker is a representation of stagg`s continuing commitment to produce the best and
highest quality audio products possible at an affordable price.
The SMSDP7-X Series is a two-way active loudspeaker encased in a light weight cabinet.
This speaker has been designed to be used as both a portable and a permanently installed unit.
The speaker includes a poll mount slot and rubber feet on the bottom of the unit for portable
applications and also includes rigging points on the top ,and bottom of the unit for permanent and
ight installations.
Please read and understand this manual completely before attempting to operate your new
speaker system . This booklet contains important information concerning the proper and safe
operation of you new speaker.
Caution !
There are no user serviceable parts inside this speaker.
Do not attempt any repairs, without being instructed to do so by an authorized stagg technician.
Doing so will void your manufactures warranty.
In the unlikely event your speaker may require service, please contact stagg.
Unpacking :
Every SMSDP700 Series has been thoroughly tested and has been shipped in
perfect operating condition .
Carefully check the shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged carefully inspect your units for any damage and be sure all
accessories necessary to operate the system have arrived intact.
In the event damage has been found or parts are missing , please contact your dealer for further
instructions.
4
5
Main Features
1. 2-way, active bi-amplied speaker system
2. Low Frequency driver and Titanium High Frequency compression driver provide exceptional
clarity, high power handling capability and maximum efciency
3. State-of-the-art, high efciency switch mode power supply with a class D low frequency
power amplier and a class A/B or class D high frequency amplier
4. Low frequency power (Class D) 300W RMS
5. High frequency power (Class A/B) 60W RMS for 12 ¨ and 80W RMS for 15 ¨
6. Active signal limiting system with LED indicator on rear panel
7. Flyable & stand mountable
8. Treble, bass and volume output control
9. One microphone inputs (XLR & 1/4” stereo) with separate microphone volume control
10. Treble, bass and volume output control
11. XLR & RCA line inputs
12. XLR through output
13. Time Aligned Electronic Crossover
14. Full Protection system: DC, overload, short circuit, thermal, On / Off mute and LF / HF Limiters
15. Enclosure Material Injection Moulded Polypropylene
6
SMS1 2D P7 00
CLIP
MIC LEVE L
MIN MAX
LINE LEV EL
MIN MAX
VOLUME
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPUT
MIC
INPUT
R L
LINE INP UT
HF:1 .35 80W ( 34mm Ti do me driv e)
＂
＂
LF:1 2 300W (6 0mm voi ce coil /50 oz ma gnet)
ACT IVE SOU ND REIN FORCE MENT SYS TEM
Inte rnal Sw itch Mo de Powe r Suppl y(SMP S)
Revo lutio nary Cl ass-D Am plifi er Techno logy
Nomi nal Imp edanc e: 8 ohm
AC 230V 50 Hz
POWER
GROUN D
1
2
3
4
2
5
55
66
7
Controls and Features
1.POLE MOUNT SOCKET-This socket is designed to fit a standard speaker
pole mount or tripod speaker stand.
2.RIGGING POINTS-This series speaker has rigging points . These points are
to be used to fly or suspend the speaker in the air by some means . Be sure
to follow the flying outlines.
3.HIGH FREQUENCY TRANSDUCER - This unit is used to reproduce the high
frequency response..
4.WOOFER-The high-powered woofer is used to reproduce the
midrange and low frequencies.
5.TRANSPORT HANDLE-This series speakers come with built-in
heavy-duty transportation handle . Use this handle for secure
and easy transportation.
6.LUGGAGE-STYLE WHEELS-
.
allowing the unit to be easily
carried or pulled along on its luggage-style wheels
7.POLE MOUNT LOCKING BOLT- This pin is used to secure the
speaker in place when mounting the speaker in a pole mount
configuration . Always be sure to tighten down on the locking
bolt to prevent the speaker from shifting during use.
USB
MMC
SD
PLAY VOL + V OL- EQ SD PO WER
PAUSE N EX T P REV PRT USB STOP
AC 230V 50H z
POWER
GROUND
SMS15DP760LCD
HF:1.75 8 0W (4 4mm Ti d ome d riv e)
＂
＂
LF:15 300 W (75 mm vo ice c oil /60 oz magnet)
ACTIVE SO UND R EIN FOR CEM ENT SYS TEM
Interna l Swi tch M ode P owe r Sup ply(SMPS)
Revolut ion ary C las s-D Am pli fier Tech nol ogy
Nominal I mpe dan ce: 8 o hm
CLI P
MIC L EVEL
MIN M AX
LIN E LEVEL
MIN M AX
VOL UME
MIN M AX
-12
TRE BL E
+12
BAS S
-12 + 12
POW ER
LIN E
OUT PU T
MIC
INP UT
R L
LIN E IN PU T
SMS15DP760LCD REAR PANEL DESCRIPTION
1
2
3
4
5
6
7
9
10
11
12
13
15
16
8
14
1. Mic XLR Input - Plug a mic directly into this port for public address
usage and let your voice be heard.
2. 1/4” MIC Input – Plug a mic directly into this port.
3. Balanced RCA Li ne Input – This connection is designed to accept
a balanced line input signal from a mixeror other line level device
with a balanced output jack. Use a balanced cable when the signal
cable length exceeds 15 feet, this will reduce excessive signal loss.
Be sure to connect only line level input devices such as mixers
and tape machines to this jack.
4. Balanced XLR Li ne Input – This connection is designed to
accept a balanced line input signal from a mixer or other line level
device with a balanced output jack. Use a balanced cable when
the signal cable length exceeds 15 feet, this will reduce excessive
signal loss.5.1/4” Line Output Jack – This jack is used to send
the incoming line level signal from either of the Line Level Inputs
Jacks to other powered speaker.
38
6. XLR LINE Output – Using a XLR cable, use this port to daisy chain from your this speaker to other powered
speaker.
7.Main Power Inlet – This connector is used to supply main power to the unit via the included detachable power
cord.
8.Fuse Holder – This housing stores the 3.15 amp GMA protective fuse. Always replace with the exact same type
fuse, unless otherwise instructed,
9. Microphone input Volume – This knob is used to increase or decrease the volume output on your speaker.
10. Line level input volume – This knob is used to regulate the output signal of theline level source connected to
the Line Level Inputs.
11. output volume – This knob is used to regulate the output signal being sent to other powered speaker.
12. Treble control – This knob is used to regulate the amount treble applied to the output signal. The maximum
amount of treble gain is +12dB and the maximum amount of treble decrease is -12dB. Turning the knob in a
counter-clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in a
clockwise direction will increase the amount of treble applied to a channel signal.
13. Bass Control – This knob is used to regulate the amount bass applied to the
output signal. The maximum amount of bass gain is +12dB and the maximum amount of bass decrease is -12dB.
Turning the knob in a counter-clockwise direction will decrease the amount of bass applied to a channel signal,
turning the knob in a clockwise direction will increase the amount of bass applied to a channel signal.
14. Power indica tor led - LED lights up to indicate the speaker is on.
15. Clip Led - If this LED is lit it means your signal is clipping. To stop the signal from clipping lower the volume
to the point where the LED is blinking along with the bass beat.
16. AC VOLTOLTOLTAGEGE SELEELEELECTOTOR - This switch is used to change the operating voltage.
Operating voltage can be toggled between 115v or 230v/50~60Hz. Be sure the selector is set to the proper
voltage for your area before attempting to operate the unit. Always be sure main power is shut off before change
the position of the Voltage Selector Switch.
Controls and Features
1. POLE MOUNT SOCKET
This socket is designed to t a standard 35mm speaker pole mount or tripod speaker stand.
2. RIGGING POINTS
This series speaker has rigging points. These points are to be used to y or suspend the
speaker in the air by some means. Be sure to follow the ying outlines.
3. HIGH FREQUENCY TRANSDUCER
This unit is used to reproduce the high frequency response..
4. WOOFER
The high-powered woofer is used to reproduce the midrange and low frequencies.
5. TRANSPORT HANDLE
This series speakers come with built-in heavy-duty transportation handle .
Use this handle for secure and easy transportation.
6. LUGGAGE-STYLE WHEELS
allowing the unit to be easily carried or pulled along on its luggage-style wheels.
DO NOT USE ON STAIRS OR ROUGH SURFACE .
7. POLE MOUNT LOCKING BOLT
This pin is used to secure the speaker in place when mounting the speaker in a pole
mount con guration . Always be sure to tighten down on the locking
6
7
Typical speaker output setup
Introduction
Introduction : Congratulations and thank you for purchasing the stagg SMSDP7-X Series
professional sound reinforcement loudspeaker . This loudspeaker is a representation of stagg`s
continuing commitment to produce the best and highest quality audio products possible at an
affordable price. The SMSDP7-X Series is a two-way active loudspeaker encased in a light weight
cabinet . This speaker has been designed to be used as both a portable and a permanently
installed unit . The speaker includes a poll mount slot and rubber feet on the bottom of the unit
for portable applications and also includes rigging points on the top ,and bottom of the unit for
permanent and flight installations . Please read and understand this manual completely before
attempting to operate your new speaker system . This booklet contains important information
concerning the proper and safe operation of you new speaker.
Customer Support : Stagg provides a toll free customer support line , to provide set up
help and answer any question should you encounter problems during your initial set up or
operation. You may also visit us on the web at www.stagg.com for any comments or suggestions .
Service Hours are Monday through Friday 9 :00 a.m to 5 :30 p.m. Pacific Standard Time .
VOICE :
Fax :
E-mail :
Caution ! There are no user serviceable parts inside this speaker . Do not attempt any repairs ,
without being instructed to do so by an authorized stagg technician . Doing so will void your
manufactures warranty . In the unlikely event your speaker may require service , please contact
stagg.
Unpacking : Every SMSDP7-A Series has been thoroughly tested and has been shipped in
perfect operating condition . Carefully check the shipping carton for damage that may have
occurred during shipping . If the carton appears to be damaged carefully inspect your units for
any damage and be sure all accessories necessary to operate the system have arrived intact .
In the event damage has been found or parts are missing , please contact our toll free customer
support number for further instructions . Please do not return the speaker to your dealer without
first contacting customer support .
Main Features
1. 2-way, active bi-amplified speaker system
2. Low Frequency driver and Titanium High Frequency compression driver provide exceptional
clarity, high power handling capability and maximum efficiency
3. State-of-the-art, high efficiency switch mode power supply with a class D low frequency
power amplifier and a class A/B or class D high frequency amplifier
4. Low frequency power (Class D) 300W RMS
5. High frequency power (Class A/B) 75W RMS
6. Active signal limiting system with LED indicator on rear panel
7. Flyable & stand mountable
8. Treble, bass and volume output control
9. One microphone inputs (XLR & 1/4 " stereo) with separate microphone volume control
10. Treble, bass and volume output control
11.XLR & RCA line inputs
12. XLR through output
13.Time Aligned Electronic Crossover
14. Full Protection system: DC, overload, short circuit, thermal, On / Off mute and
LF / HF Limiters
15. Enclosure Material Injection Moulded Polypropylene
2
Typical speaker output setup
250W
8 ohms
96dB
90 H x 60 V
2.5KHz
FB1203
LINE IN
BAL
OR
UNBAL
L R
2
L L
R R
TAPE IN
TAPE OUT
7
4
2
0
-10
-7
-4
-2
+15 -15
L R
PEAKPEAKPEAKPEAK PEAK
LO - CUT LO - CUT
100Hz 100Hz
PH
METER
ROOM/PH ONESSTEREO LINE IN 5/6
EFF SEND MON OUT
MAIN OUT
RL
RL
INSERT
RL
RL
TAPE
0
0
RETURN
EFF
MON
SELECT
MAIN ROOM
MAIN OUT
TAPE
DC
dB
BAL
OR
UNBAL
-20
LOW
GAIN
HIGH
MID
MON
EFF
PAN
VOL
0
+15-15
0
-60-20
0
-60-20
0
+15-15
+15-15
0
0
0
0
0
0
RL
0
0
LOW
GAIN
HIGH
MID
MON
EFF
PAN
VOL
0
+15-15
0
+15-15
+15-15
0
0
0
0
0
0
RL
0
0
LOW
GAIN
HIGH
MID
MON
EFF
PAN
VOL
0
0
0
+15-15
0
+15-15
+15-15
0
0
0
0
0
0
RL
0
0
LOW
GAIN
HIGH
MID
MON
EFF
PAN
VOL
0
0
0
+15-15
0
+15-15
+15-15
0
0
0
0
0
0
RL
0
0
0
0
0
0
0
0
0
0
STEREO LINE IN 3/4
MAIN SECT ION
5/ 612 3/ 4
. . .
PROGRAM
12 - 196mS
UP
DOWN
DIG ITAL EFFE CT
mS
LINE IN
BAL
OR
UNBAL
1
1
EFF RETUR N
IN
MIC
BAL IN
MIC
BAL IN
MIC
BAL IN
Connections are the same for SMS15DP760 & SMS15DP760LCD
SMS12DP700 SMS12DP700LCD
SMSDP7-A SERIES SPEAKER LOOPING
FROM MIXER
TO NEXT SPEAKER
SMS1 2D P700
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF:1 .35 80W ( 34mm Ti do me driv e)
＂
＂
LF:1 2 300W (6 0mm voi ce coil /50 oz ma gnet)
ACT IVE SOU ND REIN FORCE MENT SY STEM
Inte rnal Sw itch Mo de Powe r Suppl y(SMP S)
Revo lutio nary Cl ass-D Am plifi er Techno logy
Nomi nal Imp edanc e: 8 ohm
AC 230V 5 0Hz
POWE R
GROU ND
SMS12 DP 70 0L CD
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF:1. 35 80W (3 4mm Ti dom e drive )
＂
＂
LF:12 3 00W (60 mm voic e coil/ 50 oz mag net)
ACTIV E SOUND R EINFO RCEME NT SYST EM Internal S witch M ode Pow er Supp ly(SM PS)
Revol ution ary Cla ss-D Amp lifie r Technol ogy Nominal Imp edanc e: 8 ohm
AC 230V 50 Hz
POWER
GROUN D
USB
MMC
SD
PLAY VOL + VOL- EQ SD POWER
PAUSE NEXT PREV PRT USB STO P
XLR-XLR balanced cables
XLR-XLR balanced cables
SMS1 2D P700
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF:1 .35 80W ( 34mm Ti do me driv e)
＂
＂
LF:1 2 300W (6 0mm voi ce coil /50 oz ma gnet)
ACT IVE SOU ND REIN FORCE MENT SY STEM
Inte rnal Sw itch Mo de Powe r Suppl y(SMP S)
Revo lutio nary Cl ass-D Am plifi er Techno logy
Nomi nal Imp edanc e: 8 ohm
AC 230V 5 0Hz
POWE R
GROU ND
SMS12 DP 70 0L CD
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF:1. 35 80W (3 4mm Ti dom e drive )
＂
＂
LF:12 3 00W (60 mm voic e coil/ 50 oz mag net)
ACTIV E SOUND R EINFO RCEME NT SYST EM Internal S witch M ode Pow er Supp ly(SM PS)
Revol ution ary Cla ss-D Amp lifie r Technol ogy Nominal Imp edanc e: 8 ohm
AC 230V 50 Hz
POWER
GROUN D
USB
MMC
SD
PLAY VOL + VOL- EQ SD POWER
PAUSE NEXT PREV PRT USB STO P
9
SMS12DP SERIES SPEAKER LOOPING
How to connect SMS DP in Series.
Connections are the same for SMS12DP700, SMS12DP700LCD,
SMS15DP760 and SMS15DP760LCD
Introduction
Introduction : Congratulations and thank you for purchasing the stagg SMSDP7-X Series
professional sound reinforcement loudspeaker . This loudspeaker is a representation of stagg`s
continuing commitment to produce the best and highest quality audio products possible at an
affordable price. The SMSDP7-X Series is a two-way active loudspeaker encased in a light weight
cabinet . This speaker has been designed to be used as both a portable and a permanently
installed unit . The speaker includes a poll mount slot and rubber feet on the bottom of the unit
for portable applications and also includes rigging points on the top ,and bottom of the unit for
permanent and flight installations . Please read and understand this manual completely before
attempting to operate your new speaker system . This booklet contains important information
concerning the proper and safe operation of you new speaker.
Customer Support : Stagg provides a toll free customer support line , to provide set up
help and answer any question should you encounter problems during your initial set up or
operation. You may also visit us on the web at www.stagg.com for any comments or suggestions .
Service Hours are Monday through Friday 9 :00 a.m to 5 :30 p.m. Pacific Standard Time .
VOICE :
Fax :
E-mail :
Caution ! There are no user serviceable parts inside this speaker . Do not attempt any repairs ,
without being instructed to do so by an authorized stagg technician . Doing so will void your
manufactures warranty . In the unlikely event your speaker may require service , please contact
stagg.
Unpacking : Every SMSDP7-A Series has been thoroughly tested and has been shipped in
perfect operating condition . Carefully check the shipping carton for damage that may have
occurred during shipping . If the carton appears to be damaged carefully inspect your units for
any damage and be sure all accessories necessary to operate the system have arrived intact .
In the event damage has been found or parts are missing , please contact our toll free customer
support number for further instructions . Please do not return the speaker to your dealer without
first contacting customer support .
Main Features
1. 2-way, active bi-amplified speaker system
2. Low Frequency driver and Titanium High Frequency compression driver provide exceptional
clarity, high power handling capability and maximum efficiency
3. State-of-the-art, high efficiency switch mode power supply with a class D low frequency
power amplifier and a class A/B or class D high frequency amplifier
4. Low frequency power (Class D) 300W RMS
5. High frequency power (Class A/B) 75W RMS
6. Active signal limiting system with LED indicator on rear panel
7. Flyable & stand mountable
8. Treble, bass and volume output control
9. One microphone inputs (XLR & 1/4 " stereo) with separate microphone volume control
10. Treble, bass and volume output control
11.XLR & RCA line inputs
12. XLR through output
13.Time Aligned Electronic Crossover
14. Full Protection system: DC, overload, short circuit, thermal, On / Off mute and
LF / HF Limiters
15. Enclosure Material Injection Moulded Polypropylene
2
Typical speaker output setup
250W
8 ohms
96dB
90 H x 60 V
2.5KHz
FB1203
LINE IN
BAL
OR
UNBAL
L R
2
L L
R R
TAPE IN
TAPE OUT
7
4
2
0
-10
-7
-4
-2
+15 -15
L R
PEAKPEAKPEAKPEAK PEAK
LO - CUT LO - CUT
100Hz 100Hz
PH
METER
ROOM/PH ONESSTEREO LINE IN 5/6
EFF SEND MON OUT
MAIN OUT
RL
RL
INSERT
RL
RL
TAPE
0
0
RETURN
EFF
MON
SELECT
MAIN ROOM
MAIN OUT
TAPE
DC
dB
BAL
OR
UNBAL
-20
LOW
GAIN
HIGH
MID
MON
EFF
PAN
VOL
0
+15-15
0
-60-20
0
-60-20
0
+15-15
+15-15
0
0
0
0
0
0
RL
0
0
LOW
GAIN
HIGH
MID
MON
EFF
PAN
VOL
0
+15-15
0
+15-15
+15-15
0
0
0
0
0
0
RL
0
0
LOW
GAIN
HIGH
MID
MON
EFF
PAN
VOL
0
0
0
+15-15
0
+15-15
+15-15
0
0
0
0
0
0
RL
0
0
LOW
GAIN
HIGH
MID
MON
EFF
PAN
VOL
0
0
0
+15-15
0
+15-15
+15-15
0
0
0
0
0
0
RL
0
0
0
0
0
0
0
0
0
0
STEREO LINE IN 3/4
MAIN SECT ION
5/ 612 3/ 4
. . .
PROGRAM
12 - 196mS
UP
DOWN
DIG ITAL EFFE CT
mS
LINE IN
BAL
OR
UNBAL
1
1
EFF RETUR N
IN
MIC
BAL IN
MIC
BAL IN
MIC
BAL IN
Connections are the same for SMS15DP760 & SMS15DP760LCD
SMS12DP700
SMS12DP700LCD
SMSDP7-A SERIES SPEAKER LOOPING
FROM MIXER
TO NEXT SPEAKER
SMS1 2D P700
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF:1 .35 80W ( 34mm Ti do me driv e)
＂
＂
LF:1 2 300W (6 0mm voi ce coil /50 oz ma gnet)
ACT IVE SOU ND REIN FORCE MENT SY STEM
Inte rnal Sw itch Mo de Powe r Suppl y(SMP S)
Revo lutio nary Cl ass-D Am plifi er Techno logy
Nomi nal Imp edanc e: 8 ohm
AC 230V 5 0Hz
POWE R
GROU ND
SMS12 DP 70 0L CD
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF:1. 35 80W (3 4mm Ti dom e drive )
＂
＂
LF:12 3 00W (60 mm voic e coil/ 50 oz mag net)
ACTIV E SOUND R EINFO RCEME NT SYST EM Internal S witch M ode Pow er Supp ly(SM PS)
Revol ution ary Cla ss-D Amp lifie r Technol ogy Nominal Imp edanc e: 8 ohm
AC 230V 50 Hz
POWER
GROUN D
USB
MMC
SD
PLAY VOL + VOL- EQ SD POWER
PAUSE NEXT PREV PRT USB STO P
XLR-XLR balanced cables
XLR-XLR balanced cables
SMS1 2D P700
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF:1 .35 80W ( 34mm Ti do me driv e)
＂
＂
LF:1 2 300W (6 0mm voi ce coil /50 oz ma gnet)
ACT IVE SOU ND REIN FORCE MENT SY STEM
Inte rnal Sw itch Mo de Powe r Suppl y(SMP S)
Revo lutio nary Cl ass-D Am plifi er Techno logy
Nomi nal Imp edanc e: 8 ohm
AC 230V 5 0Hz
POWE R
GROU ND
SMS12 DP 70 0L CD
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF:1. 35 80W (3 4mm Ti dom e drive )
＂
＂
LF:12 3 00W (60 mm voic e coil/ 50 oz mag net)
ACTIV E SOUND R EINFO RCEME NT SYST EM Internal S witch M ode Pow er Supp ly(SM PS)
Revol ution ary Cla ss-D Amp lifie r Technol ogy Nominal Imp edanc e: 8 ohm
AC 230V 50 Hz
POWER
GROUN D
USB
MMC
SD
PLAY VOL + VOL- EQ SD POWER
PAUSE NEXT PREV PRT USB STO P
9
Introduction
Introduction : Congratulations and thank you for purchasing the stagg SMSDP7-X Series
professional sound reinforcement loudspeaker . This loudspeaker is a representation of stagg`s
continuing commitment to produce the best and highest quality audio products possible at an
affordable price. The SMSDP7-X Series is a two-way active loudspeaker encased in a light weight
cabinet . This speaker has been designed to be used as both a portable and a permanently
installed unit . The speaker includes a poll mount slot and rubber feet on the bottom of the unit
for portable applications and also includes rigging points on the top ,and bottom of the unit for
permanent and flight installations . Please read and understand this manual completely before
attempting to operate your new speaker system . This booklet contains important information
concerning the proper and safe operation of you new speaker.
Customer Support : Stagg provides a toll free customer support line , to provide set up
help and answer any question should you encounter problems during your initial set up or
operation. You may also visit us on the web at www.stagg.com for any comments or suggestions .
Service Hours are Monday through Friday 9 :00 a.m to 5 :30 p.m. Pacific Standard Time .
VOICE :
Fax :
E-mail :
Caution ! There are no user serviceable parts inside this speaker . Do not attempt any repairs ,
without being instructed to do so by an authorized stagg technician . Doing so will void your
manufactures warranty . In the unlikely event your speaker may require service , please contact
stagg.
Unpacking : Every SMSDP7-A Series has been thoroughly tested and has been shipped in
perfect operating condition . Carefully check the shipping carton for damage that may have
occurred during shipping . If the carton appears to be damaged carefully inspect your units for
any damage and be sure all accessories necessary to operate the system have arrived intact .
In the event damage has been found or parts are missing , please contact our toll free customer
support number for further instructions . Please do not return the speaker to your dealer without
first contacting customer support .
Main Features
1. 2-way, active bi-amplified speaker system
2. Low Frequency driver and Titanium High Frequency compression driver provide exceptional
clarity, high power handling capability and maximum efficiency
3. State-of-the-art, high efficiency switch mode power supply with a class D low frequency
power amplifier and a class A/B or class D high frequency amplifier
4. Low frequency power (Class D) 300W RMS
5. High frequency power (Class A/B) 75W RMS
6. Active signal limiting system with LED indicator on rear panel
7. Flyable & stand mountable
8. Treble, bass and volume output control
9. One microphone inputs (XLR & 1/4 " stereo) with separate microphone volume control
10. Treble, bass and volume output control
11.XLR & RCA line inputs
12. XLR through output
13.Time Aligned Electronic Crossover
14. Full Protection system: DC, overload, short circuit, thermal, On / Off mute and
LF / HF Limiters
15. Enclosure Material Injection Moulded Polypropylene
2
Typical speaker output setup
250W
8 ohms
96dB
90 H x 60 V
2.5KHz
FB1203
LINE IN
BAL
OR
UNBAL
L R
2
L L
R R
TAPE IN
TAPE OUT
7
4
2
0
-10
-7
-4
-2
+15 -15
L R
PEAKPEAKPEAKPEAK PEAK
LO - CUT LO - CUT
100Hz 100Hz
PH
METER
ROOM/PH ONESSTEREO LINE IN 5/6
EFF SEND MON OUT
MAIN OUT
RL
RL
INSERT
RL
RL
TAPE
0
0
RETURN
EFF
MON
SELECT
MAIN ROOM
MAIN OUT
TAPE
DC
dB
BAL
OR
UNBAL
-20
LOW
GAIN
HIGH
MID
MON
EFF
PAN
VOL
0
+15-15
0
-60-20
0
-60-20
0
+15-15
+15-15
0
0
0
0
0
0
RL
0
0
LOW
GAIN
HIGH
MID
MON
EFF
PAN
VOL
0
+15-15
0
+15-15
+15-15
0
0
0
0
0
0
RL
0
0
LOW
GAIN
HIGH
MID
MON
EFF
PAN
VOL
0
0
0
+15-15
0
+15-15
+15-15
0
0
0
0
0
0
RL
0
0
LOW
GAIN
HIGH
MID
MON
EFF
PAN
VOL
0
0
0
+15-15
0
+15-15
+15-15
0
0
0
0
0
0
RL
0
0
0
0
0
0
0
0
0
0
STEREO LINE IN 3/4
MAIN SECT ION
5/ 612 3/ 4
. . .
PROGRAM
12 - 196mS
UP
DOWN
DIG ITAL EFFE CT
mS
LINE IN
BAL
OR
UNBAL
1
1
EFF RETUR N
IN
MIC
BAL IN
MIC
BAL IN
MIC
BAL IN
Connections are the same for SMS15DP760 & SMS15DP760LCD
SMS12DP700 SMS12DP700LCD
SMSDP7-A SERIES SPEAKER LOOPING
FROM MIXER
TO NEXT SPEAKER
SMS1 2D P700
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF:1 .35 80W ( 34mm Ti do me driv e)
＂
＂
LF:1 2 300W (6 0mm voi ce coil /50 oz ma gnet)
ACT IVE SOU ND REIN FORCE MENT SY STEM
Inte rnal Sw itch Mo de Powe r Suppl y(SMP S)
Revo lutio nary Cl ass-D Am plifi er Techno logy
Nomi nal Imp edanc e: 8 ohm
AC 230V 5 0Hz
POWE R
GROU ND
SMS12 DP 70 0L CD
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF:1. 35 80W (3 4mm Ti dom e drive )
＂
＂
LF:12 3 00W (60 mm voic e coil/ 50 oz mag net)
ACTIV E SOUND R EINFO RCEME NT SYST EM Internal S witch M ode Pow er Supp ly(SM PS)
Revol ution ary Cla ss-D Amp lifie r Technol ogy Nominal Imp edanc e: 8 ohm
AC 230V 50 Hz
POWER
GROUN D
USB
MMC
SD
PLAY VOL + VOL- EQ SD POWER
PAUSE NEXT PREV PRT USB STO P
XLR-XLR b
alanced cables
XLR-XLR balanced cables
SMS1 2D P700
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF:1 .35 80W ( 34mm Ti do me driv e)
＂
＂
LF:1 2 300W (6 0mm voi ce coil /50 oz ma gnet)
ACT IVE SOU ND REIN FORCE MENT SY STEM
Inte rnal Sw itch Mo de Powe r Suppl y(SMP S)
Revo lutio nary Cl ass-D Am plifi er Techno logy
Nomi nal Imp edanc e: 8 ohm
AC 230V 5 0Hz
POWE R
GROU ND
SMS12 DP 70 0L CD
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF:1. 35 80W (3 4mm Ti dom e drive )
＂
＂
LF:12 3 00W (60 mm voic e coil/ 50 oz mag net)
ACTIV E SOUND R EINFO RCEME NT SYST EM Internal S witch M ode Pow er Supp ly(SM PS)
Revol ution ary Cla ss-D Amp lifie r Technol ogy Nominal Imp edanc e: 8 ohm
AC 230V 50 Hz
POWER
GROUN D
USB
MMC
SD
PLAY VOL + VOL- EQ SD POWER
PAUSE NEXT PREV PRT USB STO P
9
8
SMS15DP700 REAR PANEL DESCRIPTION
6. XLR LINE Output – Using a XLR cable, use this port to daisy chain from your this speaker to other
powered speaker.
7.Main Power Inlet – This connector is used to supply main power to the unit via the included detachable
power cord.
8.Fuse Holder – This housing stores the 3.15 amp GMA protective fuse. Always replace with the exact
same type fuse, unless otherwise instructed,
9. Microphone input Volume – This knob is used to increase or decrease the volume output on your
speaker.
10. Line level input volume – This knob is used to regulate the output signal of the line level source
connected to the Line Level Inputs.
11. output volume – This knob is used to regulate the output signal being sent to other powered speaker.
12. Treble control – This knob is used to regulate the amount treble applied to the output signal. The
maximum amount of treble gain is +12dB and the maximum amount of treble decrease is -12dB.
Turning the knob in a counter-clockwise direction will decrease the amount of treble applied to a
channel signal, turning the knob in a clockwise direction will increase the amount of treble applied to
a channel signal.
13. Bass Control – This knob is used to regulate the amount bass applied to the output signal. The
maximum amount of bass gain is +12dB and the maximum amount of bass decrease is -12dB. Turning
the knob in a counter-clockwise direction will decrease the amount of bass applied to a channel signal,
turning the knob in a clockwise direction will increase the amount of bass applied to a channel signal.
14. Power indica tor led - LED lights up to indicate the speaker is on.
15. Clip Led - If this LED is lit it means your signal is clipping. To stop the signal from clipping lower
the volume to the point where the LED is blinking along with the bass beat.
16. AC VOLTOLTOLTAGEGE SELEELEELECTOTOR - This switch is used to change the operating
voltage. Operating voltage can be toggled between 115v or 230v/50~60Hz. Be sure the selector is
set to the proper voltage for your area before attempting to operate the unit. Always be sure main
power is shut off before change the position of the Voltage Selector Switch.
SMS15DP700
CLIP
MIC LEVEL
MIN MAX
LINE LEVEL
MIN MAX
VOLUME
MIN MAX
-12
TRE BL E
+12
BASS
-12 +12
POWER
LINE
OUTPUT
MIC
INPUT
R L
LINE INPUT
HF:1.75 80W (44mm Ti dome dri ve)
＂
＂
LF:15 300W (70mm voice coi l/60 o z magn et)
ACTIVE SOUND REINFORCEMENT SYSTEM
Internal Switch Mode Pow er Sup ply( SMPS )
Revolutionary Class- D Ampli fier Techno logy
Nominal Impedance: 8 ohm
AC 230V 5 0Hz
POWE R
GROU ND
1
2
3
4
5
6
7
9
10
11
12
13
15
16
8
14
1. Mic XLR Input - Plug a mic directly into
this port for public address usage and let
your voice be heard.
2. 1/4” MIC Input – Plug a mic directly in
to this port.
3. Balanced RCA Li ne Input – This connection
is designed to accept a balanced line input
signal from a mixer or other line level device
with a balanced output jack. Use a balanced
cable when the signal cable length exceeds
15 feet, this will reduce excessive signal loss.
Be sure to connect only line level input devices
such as mixers and tape machines to this jack.
4. Balanced XLR Li ne Input – This connection
is designed to accept a balanced line input signal
from a mixer or other line level device with
a balanced output jack. Use a balanced
cable when the signal cable length exceeds
15 feet, this will reduce excessive signal loss.
5.1/4” Line Output Jack – This jack is used
to send the incoming line level signal from
either of the Line Level Inputs Jacks to other
powered speaker.
SMS12DP700LCD REAR PANEL DESCRIPTION
6. XLR LINE Output – Using a XLR cable, use this port to daisy chain from your this speaker to other powered
speaker.
7.Main Power Inlet – This connector is used to supply main power to the unit via the included detachable power
cord.
8.Fuse Holder – This housing stores the 3.15 amp GMA protective fuse. Always replace with the exact same type
fuse, unless otherwise instructed,
9. Microphone input Volume – This knob is used to increase or decrease the volume output on your speaker.
10. Line level input volume – This knob is used to regulate the output signal of the line level source connected
to the Line Level Inputs.
11. output volume – This knob is used to regulate the output signal being sent to other powered speaker.
12. Treble control – This knob is used to regulate the amount treble applied to the output signal. The maximum
amount of treble gain is +12dB and the maximum amount of treble decrease is -12dB. Turning the knob in a
counter-clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in a
clockwise direction will increase the amount of treble applied to a channel signal.
13. Bass Control – This knob is used to regulate the amount bass applied to the output signal. The maximum
amount of bass gain is +12dB and the maximum amount of bass decrease is -12dB. Turning the knob in a
counter-clockwise direction will decrease the amount of bass applied to a channel signal, turning the knob in a
clockwise direction will increase the amount of bass applied to a channel signal.
14. Power indica tor led - LED lights up to indicate the speaker is on.
15. Clip Led - If this LED is lit it means your signal is clipping. To stop the signal from clipping lower the volume to
the point where the LED is blinking along with the bass beat.
16. AC VOLTOLTOLTAGEGE SELEELEELECTOTOR - This switch is used to change the operating voltage. Operating
voltage can be toggled between 115v or 230v/50~60Hz. Be sure the selector is set to the proper voltage for your
area before attempting to operate the unit. Always be sure main power is shut off before change the position
of the Voltage Selector Switch.
1
2
3
4
5
6
7
9
10
11
12
13
15
16
8
14
1. Mic XLR Input - Plug a mic directly into this port for public
address usage and let your voice be heard.
2. 1/4” MIC Input – Plug a mic directly into this port.
3. Balanced RCA Li ne Input – This connection is designed to
accept a balanced line input signal from a mixer or other line
level device with a balanced output jack. Use a balanced
cable when the signal cable length exceeds 15 feet, this will
reduce excessive signal loss. Be sure to connect only line level
input devices such as mixers and tape machines to this jack.
4. Balanced XLR Li ne Input – This connection is designed to
accept a balanced line input signal from a mixer or other line level
device with a balanced output jack. Use a balanced cable when
the signal cable length exceeds 15 feet, this will reduce excessive
signal loss.
5.1/4” Line Output Jack – This jack is used to send the incoming
line level signal from either of the Line Level Inputs Jacks to
other powered speaker.
SMS12DP700LCD
CLIP
MIC LEVEL
MIN MAX
LINE LEVEL
MIN MAX
VOLUME
MIN MAX
-12
TRE BL E
+12
BASS
-12 +12
POWER
LINE
OUTPUT
MIC
INPUT
R L
LI NE INPUT
HF:1 .3 5 80W (34 mm Ti d om e drive )
＂
＂
LF:1 2 30 0W (60m m vo ic e coil/ 50 o z magne t)
ACTI VE S OUND RE IN FO RCEME NT S YS TEM In terna l Sw itch Mo de P ower Su pp ly(SM PS )
Revo lu tiona ry C la ss-D Amp li fier Techno lo gy Nominal I mp ed ance: 8 o hm
AC 230V 50Hz
POWER
GROUND
USB
MMC
SD
PLAY VO L+ VO L- E Q SD P OW ER
PAUS E NEX T P REV PRT USB STOP
56
SMS12DP700 REAR PANEL DESCRIPTION
6. XLR LINE Output – Using a XLR cable, use this port to daisy chain from your this speaker to other powered
speaker.
7.Main Power Inlet – This connector is used to supply main power to the unit via the included detachable power cord.
8.Fuse Holder – This housing stores the 3.15 amp GMA protective fuse. Always replace with the exact same type
fuse, unless otherwise instructed,
9. Microphone input Volume – This knob is used to increase or decrease the volume output on your speaker.
10. Line level input volume – This knob is used to regulate the output signal of the line level source connected to
the Line Level Inputs.
11. output volume – This knob is used to regulate the output signal being sent to other powered speaker.
12. Treble control – This knob is used to regulate the amount treble applied to the output signal. The maximum
amount of treble gain is +12dB and the maximum amount of treble decrease is -12dB. Turning the knob in a
counter-clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in a
clockwise direction will increase the amount of treble applied to a channel signal.
13. Bass Control – This knob is used to regulate the amount bass applied to the output signal. The maximum
amount of bass gain is +12dB and the maximum amount of bass decrease is -12dB. Turning the knob in a
counter-clockwise direction will decrease the amount of bass applied to a channel signal, turning the knob in a
clockwise direction will increase the amount of bass applied to a channel signal.
14. Power indica tor led - LED lights up to indicate the speaker is on.
15. Clip Led - If this LED is lit it means your signal is clipping. To stop the signal from clipping lower the volume to
the point where the LED is blinking along with the bass beat.
16. AC VOLTOLTOLTAGEGE SELEELEELECTOTOR - This switch is used to change the operating voltage.
Operating voltage can be toggled between 115v or 230v/50~60Hz. Be sure the selector is set to the proper voltage
for your area before attempting to operate the unit. Always be sure main power is shut off before change the position
of the Voltage Selector Switch.
SMS12DP700
CLIP
MIC LEVEL
MIN MAX
LINE LEVEL
MIN MAX
VOLUME
MIN MAX
-12
TRE BL E
+12
BASS
-12 +12
POWER
LINE
OUTPUT
MIC
INPUT
R L
LINE INPUT
HF:1.35 80W (34mm Ti dome dri ve)
＂
＂
LF:12 300W (60mm voice coi l/50 o z magn et)
ACTIVE SOUND REINFORCEMENT SYSTEM
Internal Switch Mode Pow er Sup ply( SMPS )
Revolutionary Class- D Ampli fier Technology
Nominal Impedanc e: 8 ohm
AC 230V 5 0Hz
POWE R
GROU ND
1
2
3
4
5
6
7
9
10
11
12
13
15
16
8
14
1. Mic XLR Input - Plug a mic directly into this port for public
address usage and let your voice be heard.
2. 1/4” MIC Input – Plug a mic directly into this port.
3. Balanced RCA Li ne Input – This connection is designed
to accept a balanced line input signal from a mixer or other
line level device with a balanced output jack. Use a balanced
cable when the signal cable length exceeds 15 feet, this will
reduce excessive signal loss. Be sure to connect only line level
input devices such as mixers and tape machines to this jack.
4. Balanced XLR Li ne Input – This connection is designed to
accept a
balanced line input signal from a mixer or other line
level device with a balanced output jack. Use a balanced
cable when the signal cable length exceeds 15 feet, this will
reduce excessive signal loss.
5.1/4” Line Output Jack – This jack is used to send the
incoming line level signal from either of the Line Level
Inputs Jacks to other powered speaker.
SMS12DP700LCD REAR PANEL DESCRIPTION
6. XLR LINE Output – Using a XLR cable, use this port to daisy chain from your this speaker to
other powered speaker.
7.Main Power Inlet – This connector is used to supply main power to the unit via the included
detachable power cord.
8.Fuse Holder – This housing stores the 3.15 amp GMA protective fuse. Always replace with the
exact same type fuse, unless otherwise instructed,
9. Microphone input Volume – This knob is used to increase or decrease the volume output on your
speaker.
10. Line level input volume – This knob is used to regulate the output signal of the line level source
connected to the Line Level Inputs.
11. output volume – This knob is used to regulate the output signal being sent to other powered
speaker.
12. Treble control – This knob is used to regulate the amount treble applied to the output signal.
The maximum amount of treble gain is +12dB and the maximum amount of treble decrease is
-12dB. Turning the knob in a counter-clockwise direction will decrease the amount of treble applied
to a channel signal, turning the knob in a clockwise direction will increase the amount of treble
applied to a channel signal.
13. Bass Control – This knob is used to regulate the amount bass applied to the output signal.
The maximum amount of bass gain is +12dB and the maximum amount of bass decrease is -12dB.
Turning the knob in a counter-clockwise direction will decrease the amount of bass applied to a
channel signal, turning the knob in a clockwise direction will increase the amount of bass applied
to a channel signal.
14. Power indica tor led - LED lights up to indicate the speaker is on.
15. Clip Led - If this LED is lit it means your signal is clipping. To stop the signal from clipping lower
the volume to the point where the LED is blinking along with the bass beat.
16. AC VOLTOLTOLTAGEGE SELEELEELECTOTOR - This switch is used to change the operating
voltage. Operating voltage can be toggled between 115v or 230v/50~60Hz. Be sure the selector is
set to the proper voltage for your area before attempting to operate the unit. Always be sure main
power is shut off before change the position of the Voltage Selector Switch.
1
2
3
4
5
6
7
9
10
11
12
13
15
16
8
14
1. Mic XLR Input - Plug a mic directly into this
port for public address usage and let your voice
be heard.
2. 1/4” MIC Input – Plug a mic directly into
this port.
3. Balanced RCA Li ne Input – This connection
is designed to accept a balanced line input
signal from a mixer or other line level device
with a balanced output jack. Use a balanced
cable when the signal cable length exceeds
15 feet, this will reduce excessive signal loss.
Be sure to connect only line level input devices
such as mixers and tape machines to this jack.
4. Balanced XLR Li ne Input – This connection
is designed to accept
balanced
a
line input signal
from a mixer or other line level device with a
balanced output jack. Use a balanced cable when
the signal cable length exceeds 15 feet, this will
reduce excessive signal loss.
5.1/4” Line Output Jack – This jack is used to
send the incoming line level signal from either
of the Line Level Inputs Jacks to other powered
speaker.
SMS12DP700LCD
CLIP
MIC LEVEL
MIN MAX
LINE LEVEL
MIN MAX
VOLUME
MIN MAX
-12
TRE BL E
+12
BASS
-12 +12
POWER
LINE
OUTPUT
MIC
INPUT
R L
LI NE INPUT
HF:1 .3 5 80W (34 mm Ti d om e drive )
＂
＂
LF:1 2 30 0W (60m m vo ic e coil/ 50 o z magne t)
ACTI VE S OUND RE IN FO RCEME NT S YS TEM Inter na l Sw itch Mo de P ower Su pp ly(SM PS )
Revo lu tiona ry C lass- D Amp li fier Techno lo gy Nomi na l Imped an ce: 8 ohm
AC 230V 50Hz
POWER
GROUND
USB
MMC
SD
PLAY VO L+ VO L- E Q S D POW ER
PAUS E NEX T P RE V P RT USB STOP
4 7
SMS1 2D P7 00
CLIP
MIC LEVE L
MIN MAX
LINE LEV EL
MIN MAX
VOLUME
MIN MAX
-12
TREBLE
+12
BASS
-12 +12
POWER
LINE
OUTPUT
MIC
INPUT
R L
LINE INP UT
HF:1 .35 80W ( 34mm Ti do me driv e)
＂
＂
LF:1 2 300W (6 0mm voi ce coil /50 oz ma gnet)
ACT IVE SOU ND REIN FORCE MENT SYS TEM
Inte rnal Sw itch Mo de Powe r Suppl y(SMP S)
Revo lutio nary Cl ass-D Am plifi er Techno logy
Nomi nal Imp edanc e: 8 ohm
AC 230V 50 Hz
POWER
GROUN D
1
2
3
4
2
5
55
66
7
Controls and Features
1.POLE MOUNT SOCKET-This socket is designed to fit a standard speaker
pole mount or tripod speaker stand.
2.RIGGING POINTS-This series speaker has rigging points . These points are
to be used to fly or suspend the speaker in the air by some means . Be sure
to follow the flying outlines.
3.HIGH FREQUENCY TRANSDUCER - This unit is used to reproduce the high
frequency response..
4.WOOFER-The high-powered woofer is used to reproduce the
midrange and low frequencies.
5.TRANSPORT HANDLE-This series speakers come with built-in
heavy-duty transportation handle . Use this handle for secure
and easy transportation.
6.LUGGAGE-STYLE WHEELS-
.
allowing the unit to be easily
carried or pulled along on its luggage-style wheels
7.POLE MOUNT LOCKING BOLT- This pin is used to secure the
speaker in place when mounting the speaker in a pole mount
configuration . Always be sure to tighten down on the locking
bolt to prevent the speaker from shifting during use.
USB
MMC
SD
PLAY VOL + V OL- EQ SD PO WER
PAUSE N EX T P REV PRT USB STOP
AC 230V 50H z
POWER
GROUND
SMS15DP760LCD
HF:1.75 8 0W (4 4mm Ti d ome d riv e)
＂
＂
LF:15 300 W (75 mm vo ice c oil /60 oz magnet)
ACTIVE SO UND R EIN FOR CEM ENT SYS TEM
Interna l Swi tch M ode P owe r Sup ply(SMPS)
Revolut ion ary C las s-D Am pli fier Tech nol ogy
Nominal I mpe dan ce: 8 o hm
CLI P
MIC L EVEL
MIN M AX
LIN E LEVEL
MIN M AX
VOL UME
MIN M AX
-12
TRE BL E
+12
BAS S
-12 + 12
POW ER
LIN E
OUT PU T
MIC
INP UT
R L
LIN E IN PU T
SMS15DP760LCD REAR PANEL DESCRIPTION
1
2
3
4
5
6
7
9
10
11
12
13
15
16
8
14
1. Mic XLR Input - Plug a mic directly into this port for public address
usage and let your voice be heard.
2. 1/4” MIC Input – Plug a mic directly into this port.
3. Balanced RCA Li ne Input – This connection is designed to accept
a balanced line input signal from a mixeror other line level device
with a balanced output jack. Use a balanced cable when the signal
cable length exceeds 15 feet, this will reduce excessive signal loss.
Be sure to connect only line level input devices such as mixers
and tape machines to this jack.
4. Balanced XLR Li ne Input – This connection is designed to
accept a balanced line input signal from a mixer or other line level
device with a balanced output jack. Use a balanced cable when
the signal cable length exceeds 15 feet, this will reduce excessive
signal loss.5.1/4” Line Output Jack – This jack is used to send
the incoming line level signal from either of the Line Level Inputs
Jacks to other powered speaker.
38
6. XLR LINE Output – Using a XLR cable, use this port to daisy chain from your this speaker to other powered
speaker.
7.Main Power Inlet – This connector is used to supply main power to the unit via the included detachable power
cord.
8.Fuse Holder – This housing stores the 3.15 amp GMA protective fuse. Always replace with the exact same type
fuse, unless otherwise instructed,
9. Microphone input Volume – This knob is used to increase or decrease the volume output on your speaker.
10. Line level input volume – This knob is used to regulate the output signal of theline level source connected to
the Line Level Inputs.
11. output volume – This knob is used to regulate the output signal being sent to other powered speaker.
12. Treble control – This knob is used to regulate the amount treble applied to the output signal. The maximum
amount of treble gain is +12dB and the maximum amount of treble decrease is -12dB. Turning the knob in a
counter-clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in a
clockwise direction will increase the amount of treble applied to a channel signal.
13. Bass Control – This knob is used to regulate the amount bass applied to the
output signal. The maximum amount of bass gain is +12dB and the maximum amount of bass decrease is -12dB.
Turning the knob in a counter-clockwise direction will decrease the amount of bass applied to a channel signal,
turning the knob in a clockwise direction will increase the amount of bass applied to a channel signal.
14. Power indica tor led - LED lights up to indicate the speaker is on.
15. Clip Led - If this LED is lit it means your signal is clipping. To stop the signal from clipping lower the volume
to the point where the LED is blinking along with the bass beat.
16. AC VOLTOLTOLTAGEGE SELEELEELECTOTOR - This switch is used to change the operating voltage.
Operating voltage can be toggled between 115v or 230v/50~60Hz. Be sure the selector is set to the proper
voltage for your area before attempting to operate the unit. Always be sure main power is shut off before change
the position of the Voltage Selector Switch.
SMS15DP700 REAR PANEL DESCRIPTION
6. XLR LINE Output – Using a XLR cable, use this port to daisy chain from your this speaker to other
powered speaker.
7.Main Power Inlet – This connector is used to supply main power to the unit via the included detachable
power cord.
8.Fuse Holder – This housing stores the 3.15 amp GMA protective fuse. Always replace with the exact
same type fuse, unless otherwise instructed,
9. Microphone input Volume – This knob is used to increase or decrease the volume output on your
speaker.
10. Line level input volume – This knob is used to regulate the output signal of the line level source
connected to the Line Level Inputs.
11. output volume – This knob is used to regulate the output signal being sent to other powered speaker.
12. Treble control – This knob is used to regulate the amount treble applied to the output signal. The
maximum amount of treble gain is +12dB and the maximum amount of treble decrease is -12dB.
Turning the knob in a counter-clockwise direction will decrease the amount of treble applied to a
channel signal, turning the knob in a clockwise direction will increase the amount of treble applied to
a channel signal.
13. Bass Control – This knob is used to regulate the amount bass applied to the output signal. The
maximum amount of bass gain is +12dB and the maximum amount of bass decrease is -12dB. Turning
the knob in a counter-clockwise direction will decrease the amount of bass applied to a channel signal,
turning the knob in a clockwise direction will increase the amount of bass applied to a channel signal.
14. Power indica tor led - LED lights up to indicate the speaker is on.
15. Clip Led - If this LED is lit it means your signal is clipping. To stop the signal from clipping lower
the volume to the point where the LED is blinking along with the bass beat.
16. AC VOLTOLTOLTAGEGE SELEELEELECTOTOR - This switch is used to change the operating
voltage. Operating voltage can be toggled between 115v or 230v/50~60Hz. Be sure the selector is
set to the proper voltage for your area before attempting to operate the unit. Always be sure main
power is shut off before change the position of the Voltage Selector Switch.
SMS15DP700
CLIP
MIC LEVEL
MIN MAX
LINE LEVEL
MIN MAX
VOLUME
MIN MAX
-12
TRE BL E
+12
BASS
-12 +12
POWER
LINE
OUTPUT
MIC
INPUT
R L
LINE INPUT
HF:1.75 80W (44mm Ti dome drive)
＂
＂
LF:15 300W (70mm voice coil/60 o z magn et)
ACTIVE SOUND REINFORCEMENT SYSTEM
Internal Switch Mode Pow er Sup ply( SMPS )
Revolutionary Class- D Ampli fier Techno logy
Nominal Impedance: 8 ohm
AC 230V 5 0Hz
POWE R
GROU ND
1
2
3
4
5
6
7
9
10
11
12
13
15
16
8
14
1. Mic XLR Input - Plug a mic directly into
this port for public address usage and let
your voice be heard.
2. 1/4” MIC Input – Plug a mic directly in
to this port.
3. Balanced RCA Li ne Input – This connection
is designed to accept a balanced line input
signal from a mixer or other line level device
with a balanced output jack. Use a balanced
cable when the signal cable length exceeds
15 feet, this will reduce excessive signal loss.
Be sure to connect only line level input devices
such as mixers and tape machines to this jack.
4. Balanced XLR Li ne Input – This connection
is designed to accept a balanced line input signal
from a mixer or other line level device with
a balanced output jack. Use a balanced
cable when the signal cable length exceeds
15 feet, this will reduce excessive signal loss.
5.1/4” Line Output Jack – This jack is used
to send the incoming line level signal from
either of the Line Level Inputs Jacks to other
powered speaker.
SMS12DP700LCD REAR PANEL DESCRIPTION
6. XLR LINE Output – Using a XLR cable, use this port to daisy chain from your this speaker to other powered
speaker.
7.Main Power Inlet – This connector is used to supply main power to the unit via the included detachable power
cord.
8.Fuse Holder – This housing stores the 3.15 amp GMA protective fuse. Always replace with the exact same type
fuse, unless otherwise instructed,
9. Microphone input Volume – This knob is used to increase or decrease the volume output on your speaker.
10. Line level input volume – This knob is used to regulate the output signal of the line level source connected
to the Line Level Inputs.
11. output volume – This knob is used to regulate the output signal being sent to other powered speaker.
12. Treble control – This knob is used to regulate the amount treble applied to the output signal. The maximum
amount of treble gain is +12dB and the maximum amount of treble decrease is -12dB. Turning the knob in a
counter-clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in a
clockwise direction will increase the amount of treble applied to a channel signal.
13. Bass Control – This knob is used to regulate the amount bass applied to the output signal. The maximum
amount of bass gain is +12dB and the maximum amount of bass decrease is -12dB. Turning the knob in a
counter-clockwise direction will decrease the amount of bass applied to a channel signal, turning the knob in a
clockwise direction will increase the amount of bass applied to a channel signal.
14. Power indica tor led - LED lights up to indicate the speaker is on.
15. Clip Led - If this LED is lit it means your signal is clipping. To stop the signal from clipping lower the volume to
the point where the LED is blinking along with the bass beat.
16. AC VOLTOLTOLTAGEGE SELEELEELECTOTOR - This switch is used to change the operating voltage. Operating
voltage can be toggled between 115v or 230v/50~60Hz. Be sure the selector is set to the proper voltage for your
area before attempting to operate the unit. Always be sure main power is shut off before change the position
of the Voltage Selector Switch.
1
2
3
4
5
6
7
9
10
11
12
13
15
16
8
14
1. Mic XLR Input - Plug a mic directly into this port for public
address usage and let your voice be heard.
2. 1/4” MIC Input – Plug a mic directly into this port.
3. Balanced RCA Li ne Input – This connection is designed to
accept a balanced line input signal from a mixer or other line
level device with a balanced output jack. Use a balanced
cable when the signal cable length exceeds 15 feet, this will
reduce excessive signal loss. Be sure to connect only line level
input devices such as mixers and tape machines to this jack.
4. Balanced XLR Li ne Input – This connection is designed to
accept a balanced line input signal from a mixer or other line level
device with a balanced output jack. Use a balanced cable when
the signal cable length exceeds 15 feet, this will reduce excessive
signal loss.
5.1/4” Line Output Jack – This jack is used to send the incoming
line level signal from either of the Line Level Inputs Jacks to
other powered speaker.
SMS12DP700LCD
CLIP
MIC LEVEL
MIN MAX
LINE LEVEL
MIN MAX
VOLUME
MIN MAX
-12
TRE BL E
+12
BASS
-12 +12
POWER
LINE
OUTPUT
MIC
INPUT
R L
LI NE INPUT
HF:1 .3 5 80W (34 mm Ti d om e drive )
＂
＂
LF:1 2 30 0W (60m m vo ic e coil/ 50 o z magne t)
ACTI VE S OUND RE IN FO RCEME NT S YS TEM In terna l Sw itch Mo de P ower Su pp ly(SM PS )
Revo lu tiona ry C la ss-D Amp li fier Techno lo gy Nominal I mp ed ance: 8 o hm
AC 230V 50Hz
POWER
GROUND
USB
MMC
SD
PLAY VO L+ VO L- E Q SD P OW ER
PAUS E NEX T P REV PRT USB STOP
56
SMS12DP7 00
CLIP
MIC LEV EL
MIN MAX
LINE LE VEL
MIN MAX
VOLUM E
MIN MAX
-12
TREBL E
+12
BASS
-12 +12
POWER
LINE
OUTPU T
MIC
INPUT
R L
LINE IN PUT
HF: 1.35 80 W (34mm Ti d ome dri ve)
＂
＂
LF: 12 300W ( 60mm vo ice coi l/50 oz m agnet )
ACT IVE SOU ND REIN FORCE MENT SY ST EM
Int ernal S witch M ode Pow er Supp ly(SM PS)
Rev oluti onary C lass- D Amp lifie r Tech nolog y
Nom inal Im pedan ce: 8 ohm
AC 230V 5 0Hz
POWE R
GROU ND
1
2
3
4
2
5
55
66
7
Controls and Features
1.POLE MOUNT SOCKET-This socket is designed to fit a standard speaker
pole mount or tripod speaker stand.
2.RIGGING POINTS-This series speaker has rigging points . These points are
to be used to fly or suspend the speaker in the air by some means . Be sure
to follow the flying outlines.
3.HIGH FREQUENCY TRANSDUCER - This unit is used to reproduce the high
frequency response..
4.WOOFER-The high-powered woofer is used to reproduce the
midrange and low frequencies.
5.TRANSPORT HANDLE-This series speakers come with built-in
heavy-duty transportation handle . Use this handle for secure
and easy transportation.
6.LUGGAGE-STYLE WHEELS-
.
allowing the unit to be easily
carried or pulled along on its luggage-style wheels
7.POLE MOUNT LOCKING BOLT- This pin is used to secure the
speaker in place when mounting the speaker in a pole mount
configuration . Always be sure to tighten down on the locking
bolt to prevent the speaker from shifting during use.
USB
MMC
SD
PLAY V OL + V OL - E Q S D PO WE R
PAUS E NE XT PRE V PRT USB STOP
AC 230V 50Hz
POWER
GROUND
SMS15DP760
LCD
HF:1.75 80W (44mm Ti dome drive)
＂
＂
LF:15 300W (75mm voice coil/60 o z magne t)
ACTIVE SOUND REINFORCEMENT SYSTEM
Internal Switch Mode Power Sup ply(S MPS)
Revolutionary Class-D Ampli fier Technology
Nominal Impedance: 8 ohm
CLIP
MIC LEVE L
MIN MAX
LINE LEV EL
MIN MAX
VOLUME
MIN MAX
-12
TRE BL E
+12
BASS
-12 +12
POWER
LINE
OUTPUT
MIC
INPUT
R L
LINE INP UT
SMS15DP760LCD REAR PANEL DESCRIPTION
1
2
3
4
5
6
7
9
10
11
12
13
15
16
8
14
1. Mic XLR Input - Plug a mic directly into this port for public address
usage and let your voice be heard.
2. 1/4” MIC Input – Plug a mic directly into this port.
3. Balanced RCA Li ne Input – This connection is designed to accept
a balanced line input signal from a mixeror other line level device
with a balanced output jack. Use a balanced cable when the signal
cable length exceeds 15 feet, this will reduce excessive signal loss.
Be sure to connect only line level input devices such as mixers
and tape machines to this jack.
4. Balanced XLR Li ne Input – This connection is designed to
accept a balanced line input signal from a mixer or other line level
device with a balanced output jack. Use a balanced cable when
the signal cable length exceeds 15 feet, this will reduce excessive
signal loss.5.1/4” Line Output Jack – This jack is used to send
the incoming line level signal from either of the Line Level Inputs
Jacks to other powered speaker.
38
6. XLR LINE Output – Using a XLR cable, use this port to daisy chain from your this speaker to other powered
speaker.
7.Main Power Inlet – This connector is used to supply main power to the unit via the included detachable power
cord.
8.Fuse Holder – This housing stores the 3.15 amp GMA protective fuse. Always replace with the exact same type
fuse, unless otherwise instructed,
9. Microphone input Volume – This knob is used to increase or decrease the volume output on your speaker.
10. Line level input volume – This knob is used to regulate the output signal of theline level source connected to
the Line Level Inputs.
11. output volume – This knob is used to regulate the output signal being sent to other powered speaker.
12. Treble control – This knob is used to regulate the amount treble applied to the output signal. The maximum
amount of treble gain is +12dB and the maximum amount of treble decrease is -12dB. Turning the knob in a
counter-clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in a
clockwise direction will increase the amount of treble applied to a channel signal.
13. Bass Control – This knob is used to regulate the amount bass applied to the
output signal. The maximum amount of bass gain is +12dB and the maximum amount of bass decrease is -12dB.
Turning the knob in a counter-clockwise direction will decrease the amount of bass applied to a channel signal,
turning the knob in a clockwise direction will increase the amount of bass applied to a channel signal.
14. Power indica tor led - LED lights up to indicate the speaker is on.
15. Clip Led - If this LED is lit it means your signal is clipping. To stop the signal from clipping lower the volume
to the point where the LED is blinking along with the bass beat.
16. AC VOLTOLTOLTAGEGE SELEELEELECTOTOR - This switch is used to change the operating voltage.
Operating voltage can be toggled between 115v or 230v/50~60Hz. Be sure the selector is set to the proper
voltage for your area before attempting to operate the unit. Always be sure main power is shut off before change
the position of the Voltage Selector Switch.
Rear panel description
SMS12DP700
SMS15DP760
SMS12DP700LCD
SMS15DP760LCD
8
9
1. Mic XLR Input
Plug a mic directly into this port for public address usage and let your voice be heard.
2. 1/4” MIC Input
Plug a mic directly into this port.
3. RCA Line Input
This connection is designed to accept a line input signal from a mixer or other
line level device. Be sure to connect only line level input devices such as mixers and tape
machines to this jack.
4. Balanced XLR Li ne Input
This connection is designed to accept a balanced line input signal from a mixer or other line
level device with a balanced output. Use a balanced cable when the signal cable length
exceeds 15 feet/4,5m , this will reduce excessive signal loss.
5. 1/4” Line Output Jack
This jack is used to send the mixed incoming signals to another powered speaker.
6. XLR LINE Output
Using a XLR cable, use this port to daisy chain this speaker to another powered speaker.
7. Main Power Inlet
This connector is used to supply main power to the unit via the included detachable
power cord.
8. Fuse Holder
This housing stores the 3.15 amp GMA for 230v and 5 amp GMA for 110v protective fuse.
Always replace with the exact same type of fuse.
9. Microphone input Volume
This knob is used to increase or decrease the volume of your microphone.
10. Line level input volume
This knob is used to regulate the volume of source connected to the Line Level Inputs.
11. output volume
This knob is used to regulate the the volume of the output and the volume of the signal being
sent to another powered speaker.
12. Treble control
This knob is used to regulate the amount treble applied to the output signal.
The maximum amount of treble gain is +12dB and the maximum amount of treble decrease
is -12dB. Turning the knob in a counter-clockwise direction will decrease the amount of treble
applied to a channel signal, turning the knob in a clockwise direction will increase the amount
of treble applied to a channel signal.
13. Bass Control
This knob is used to regulate the amount bass applied to the output signal.
The maximum amount of bass gain is +12dB and the maximum amount of bass decrease
is -12dB. Turning the knob in a counter-clockwise direction will decrease the amount of bass
applied to a channel signal, turning the knob in a clockwise direction will increase the
amount of bass applied to a channel signal.
14. Power indica tor led
LED lights up to indicate the speaker is on.
15. Clip Led
If this LED is lit it means your signal is clipping. To stop the signal from clipping lower the
volume to the point where the LED is blinking along with the bass beat.
16. On/OFF switch
10
LCD Model only.
3
4
3
D C B A F E
1. LCD:
This large, blue LCD screen displays all relevant information about the function being
selected or the MP3 le (or song) being played.
2. FUNCTION SELECTOR:
This section provides front-selectable push switches, allowing you to choose between one
A. Repeat/ EQ
• Pressthisbuttononcetoplaythecurrentsongrepeatedlyuntilthe“stop”stepis
activated.
• Pressthisbuttontwiceandallloadedsongswillbeplayedoneaftertheotheruntilthe
”stop“stepisselected.
• Pressthisbuttonathirdtimetostoptherepeatingprocess.
• Pressandholdthisbuttontoselectamongdifferenttypesofequalizationappliedtothe
song currently playing.
B. Previous/ Vol -
• Pressthisbuttononcetocomebacktotheprevioussong.
• PressandholdthisbuttontolowerthevolumeoftheMP3reader.
C. Next/ Vol +
• Pressthisbuttononcetogotothenextsong.
• PressandholdthisbuttontoincreasethevolumeoftheMP3reader.
D. Play/ Pause
• Pressthisbuttontoplaythechosensong.Pressitagaintomomentarilyinterruptthe
playing.
Press a third time to continue the reading of the song.
E. Stop SW
• Pressthisbuttontoendthesong.
F. USB/SD
• UsethisknobselecttheUSBmemerycardorSD/MMCmemerycard.
3. SD (Input):
This slot is used to insert a SD (Secured Digital), non-volatile memory card with MP3
les to be read.
4. USB (Input):
In this port, plug in any USB (Universal Serial Bus) memory stick with MP3 les to be
played.
10
11
Remote control LCD Model only.
This device features all necessary push-switch selectable functions to easily operate your MP3
reader at a distance of up to 3 metres (approximately 9.8 feet) from your audio installation.
For details, please refer to the functions explained above on this page in paragraph n°2 (FUNCTION
SELECTOR), unless otherwise specied. The remote control included with your product may vary
from the one pictured here, depending on the region where it was originally purchased.
1. PLAY/PAUSE (see 2.D.)
2. STOP (see 2.E.)
3. MUTE – Mutes the sound from the MP3 player.
4. REPEAT (see 2.A.)
5. USB/SD SELECT - Use this button to choose among both audio
le memory sources available: either the SD card or the USB stick.
6. VOLUME + (see 2.C.)
7. BACK (see 2.B.)
8. EQ SELECT (see 2.A.)
9. FORWARD (see 2.C.)
10. VOLUME - (see 2.B.)
11. BATTERY - The remote control unit needs a CR2025 button-cell
battery to operate. In case of malfunction, always replace with
the same type of battery. Dispose properly of the used battery for
waste and recycling purposes.
1
3
7
8
11
9
10
6
5
4
2
12
RoHS
compliant
EMD Music 09-2011-UK
Model SMS12DP700 SMS12DP700LCD
Power type Class D Bi-Amplified Class D Bi-Amplified
Power (RMS) 300W + 60W 300W + 60W
Impedance 8Ω8Ω
Tweeter 1.35” / 34mm Ti dome drive 1.35” / 34mm Ti dome drive
Woofer 12” (65mm voice coil
/50oz magnet)
12” (65mm voice coil
/50oz magnet)
Frequency response 50Hz - 20kHz 50Hz - 20kHz
Sensitivity 98dB 98dB
MP3 NO YES
Weight 17.5kg 17.5kg
Dimensions (H x W x D) 625 x 435 x 380mm 625 x 435 x 380mm
Model SMS15DP760 SMS15DP760LCD
Power type Class D Bi-Amplified Class D Bi-Amplified
Power (RMS) 300W + 80W 300W + 80W
Impedance 8Ω8Ω
Tweeter 1.75” / 44mm Ti dome drive 1.75” / 44mm Ti dome drive
Woofer 15” (75mm voice coil/60oz
magnet)
15” (75mm voice coil/60oz
magnet)
Frequency response 40Hz - 20kHz 40Hz - 20kHz
Sensitivity 98dB 98dB
MP3 NO YES
Weight 21kg 21kg
Dimensions (H x W x D) 760 x 490 x 425mm 760 x 490 x 425mm
Technical specifications
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Stagg SMS15DP760 User manual
- Category
- Supplementary music equipment
- Type
- User manual
Stagg SMS15DP760 is a 2-Way powered loudspeaker with a recommended fuse amperage of 7.5A. This manual provides instructions on safety precautions, how to prevent risk of fire, and how to fuse the unit to prevent damage. The loudspeaker uses a 15" woofer with a 75mm voice coil and 1.75" titanium compression driver with a 25mm voice coil, for a frequency response from 45Hz-18KHz +-3dB. This loudspeaker includes protections for over-current, temperature, and RMS.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Audibax Seattle 500 User manual
-
Hammacher Schlemmer SMHS256-002 User manual
-
Sony SA-CRW55 Operating instructions
-
Philips DS8550/11 User manual
-
VocoPro SOUNDMAN Owner's manual
-
Samsung SWA-8500S User manual
-
Samsung SWA-W700 User manual
-
-
Samsung SWA-9000S User manual
-
Samsung SWA-W500/XU User manual
