Asus N100I-EM-A User manual

Industrial Motherboard

N100I-EM-A

ii

E22109

First Edition

August 2023

No part of this manual, including the products and software described in it, may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any

means, except documentation kept by the purchaser for backup purposes, without the express written

permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless

such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,

LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),

EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY

DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,

AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO

RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS

MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identication or explanation and to the

owners’ benet, without intent to infringe.

iii

Contents

Chapter 1 Product overview

1.1 Package contents ......................................................................... 1-1

1.2 Features ........................................................................................ 1-1

1.3 Specications ............................................................................... 1-2

Chapter 2 Motherboard information

2.1 Before you proceed ..................................................................... 2-1

2.2 Motherboard layout ...................................................................... 2-2

2.3 Central Processing Unit (CPU) ................................................... 2-4

2.4 System memory ........................................................................... 2-4

2.4.1 Installing a DIMM ............................................................ 2-5

2.5 Jumpers ........................................................................................ 2-6

2.6 Connectors ................................................................................. 2-11

2.6.1 Rear panel connectors .................................................. 2-11

2.6.2 Internal connectors ....................................................... 2-13

2.7 Slot .............................................................................................. 2-24

Chapter 3 BIOS setup

3.1 BIOS Setup program .................................................................... 3-1

3.2 Main menu .................................................................................... 3-2

3.2.1 System Date [Day MM/DD/YYYY] .................................. 3-2

3.2.2 System Time [HH:MM:SS] .............................................. 3-2

3.3 Advanced menu ........................................................................... 3-2

3.3.1 LVDS Conguration ........................................................ 3-2

3.3.2 PCH-FW Conguration ................................................... 3-4

3.3.3 Trusted Computing ......................................................... 3-4

3.3.4 CPU Conguration .......................................................... 3-5

3.3.5 Graphics Conguration ................................................... 3-6

3.3.6 PCI Express Conguration .............................................. 3-6

3.3.7 Super IO Conguration ................................................... 3-7

3.3.8 Serial Console Redirection ............................................. 3-8

3.3.9 SATA Conguration ........................................................ 3-9

3.3.10 Network Stack Conguration ........................................ 3-10

3.3.11 USB Conguration ........................................................ 3-10

3.3.12 NVMe Conguration ...................................................... 3-11

3.3.13 Onboard Devices Conguration .................................... 3-11

iv

3.3.14 Miscellaneous ............................................................... 3-12

3.3.15 APM Conguration ........................................................ 3-12

3.3.16 EZ-Flash ....................................................................... 3-13

3.3.17 Watchdog Timer ............................................................ 3-13

3.4 Hardware Monitor menu ............................................................ 3-14

Smart Fan Mode .......................................................................... 3-14

Smart Fan Function ...................................................................... 3-14

3.5 Security menu ............................................................................ 3-14

3.5.1 Administrator Password ................................................ 3-14

3.5.2 User Password .............................................................. 3-15

3.5.3 Secure Boot .................................................................. 3-15

3.6 Boot menu .................................................................................. 3-16

3.7 Exit menu .................................................................................... 3-16

Appendix

Notices .......................................................................................................A-1

1-1

Chapter 1: General information

1.1 Package contents

Check your industrial motherboard package for the following items.

1 x ASUS N100I-EM-A Motherboard

1 x Serial ATA 6.0 Gb/s cable

2 x M.2 screw packages

1 x ASUS I/O Shield

NOTE: If any of the above items is damaged or missing, contact your

distributor or sales representative immediately.

1.2 Features

• Built-in Intel® Celeron® Quad-core Processor N100

• One DDR4 3200/3000/2800/2666/2400/2133 MHz Non-ECC SO-DIMM up to

16GB

• 2 x SATA 6Gb/s ports, 4 x USB 3.2 Gen 1 headers, 3 x USB 2.0 headers, 3 x

COM headers, 3 x COM connectors

• 1 x PCIe 3.0/2.0 x 1 slot (x1 mode), 1 x M.2 socket (E key) , 1 x M.2 socket (M

key)

• Multi-display: 1 x VGA port, 1 x HDMI™ port, 1 x LVDS connector

Chapter 1

Product overview

N100I-EM-A

1-2

1.3 Specications

(continued on the next page)

CPU Built-in Intel® Celeron® Quad-core Processor N100

Memory 1 x DDR4, max.16GB, 3200/3000/2800/2666/2400/2133 MHz

Non-ECC Memory

Graphics

- Supports VGA output with a maximum resolution of 1920 x

1200 @ 60Hz (Default)

- Supports HDMITM output with a maximum resolution of 3840

x 2160 @ 60Hz (Default)

- Supports LVDS output with a maximum resolution of 1920 x

1200 @ 60Hz (Default)

Support up to three displays simultaneously

Expansion slots

1 x PCI Express 3.0/2.0 x1 slot (x1 mode)

1 x M.2 Socket 1 with E key, type 2230 for WIFI/BT device (PCIe

x1 /USB2.0)

1 x M.2 Socket 3 with M key, type 2242/ 2260/ 2280 (SATA/

PCIex1)

Storage

2 x SATA Gen 3.0 up to 6.0 Gb/s ports

*SATA6G_2 shares bandwidth with M.2 socket 3.

Ethernet 2 x Realtek® 8111H

Audio Realtek® ALC897 High Denition Audio

Rear panel I/O

ports

1 x VGA port

1 x HDMITM port

2 x USB 3.2 Gen 1 ports

2 x USB 2.0 ports

1 x Serial Port connector (RS232/422/485)

2 x Serial Port connectors (RS232)

2 x LAN (RJ45) ports

1 x DC-IN port

2 x Audio jacks

Internal

Connectors

1 x USB 3.2 Gen 1 header supports 2 additional USB 3.2 Gen 1

ports

1 x USB 2.0 header supports 1 USB 2.0 port

1 x Chassis Fan header

1 x Chassis Intrusion header

1 x Front Panel Audio header (F_AUDIO)

3 x Serial Port headers

1 x System Panel header (10-1 pin F_Panel)

1 x Speaker header

1 x Stereo Out header

1-3

Chapter 1: General information

Internal

Connectors

1 x Clear CMOS header

1 x COM Debug header

1 x GPIO connector

1 x LVDS Signal header

1 x LCD Panel Monitor Switch header

1 x LVDS Panel VCC Power Selection jumper

1 x LVDS Panel Backlight Enable Signal Selection jumper

1 x LVDS Backlight Panel header

1 x 4-pin ATX power connector (DC in mode)

Watchdog Timer Yes

Security 1 x SPI TPM header

Manageability WfM 2.0, WOL by PME

Power

requirement 12v DC-IN

Operation

Temperature 0~60°C

Non-Operation

Temperature -40~85°C

Relative Humidity Operational humidity: 40°C@10%~95%

OS support Windows® 10 (64bit) / Windows® IoT enterprise

Ubuntu, RedHat Enterprise, Fedora Workstation, OpenSUSE

Form Factor Mini-ITX Form Factor, 17.0cm x 17.0cm

NOTE: Specications are subject to change without notice.

2-1

Chapter 2: Motherboard information

Chapter 2

Motherboard information

2.1 Before you proceed

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

CAUTION!

• Unplug the power cord from the wall socket before touching any

component.

• Before handling components, use a grounded wrist strap or touch a safely

grounded object or a metal object, such as the power supply case, to avoid

damaging them due to static electricity.

• Hold components by the edges to avoid touching the ICs on them.

• Whenever you uninstall any component, place it on a grounded antistatic

pad or in the bag that came with the component.

• Before you install or remove any component, always remove the AC power

by unplugging the power cord from the power outlet. Failure to do so may

cause severe damage to the motherboard, peripherals, or components.

N100I-EM-A

2-2

17.0cm(6.7in)

AT_ATX_SEL

F_AUDIOAUDIO

Super

I/O

(BOTTOM)

256Mb

BIOS

M.2_(SOCKET3)

M.2(WIFI)

GPIO_CON

BATTERY

CLRTC

USB_7

TPM

SATA_PWR2 SATA_PWR1

SPEAKER

CHASSIS F_PANEL

COM4 COM5

22602280 2242

COM6

CHA_FAN

VCC_PWR SEL

DC_PWR1

DC_PWR2

COM2

HDMI

COM3

VGA

COM1

COM1_SEL

LAN1_USB_56

LAN2_U32G1_12

DDR4 So-DIMM_A (64bit, 204-pin module)

SATA6G_2SATA6G_1

PCIEX1(G3)

I2C

COM_DEBUG

Intel®

N100

ALC

897

RTL

8111H

RTL

8111H

PANEL_SW

BKLTEN_SEL

SPK_OUT

LVDS_EDP

LCD_BLKT_PANEL

U32G1_34

13

12

14

9

11

10

7

8

6

18 17 16 15

20 19

23 22

24 21

29

30

28

27

26

25

1 52 43

2.2 Motherboard layout

Place this side

towards the rear

of the chassis

NOTE: Place four screws into the holes indicated by circles to secure the

motherboard to the chassis.

CAUTION! Do not overtighten the screws! Doing so can damage the

motherboard.

NOTE: The audio codec may vary between motherboards, please consult

your sales window for the motherboards’ exact codec type.

2-3

Chapter 2: Motherboard information

Connectors/Jumpers/Slots Page

1. ATX Power connector (4-pin DC_PWR2) 2-14

2. USB 3.2 Gen 1 header (20-1 pin U32G1_34) 2-13

3. Built-in Intel® Celeron® Quad-core Processor N100 2-4

4. DDR4 SO-DIMM slot 2-4

5. LVDS Panel Backlight Enable Signal Selection jumper (3-pin BKLTEN_SEL) 2-8

6. LCD Panel Monitor Switch header (2-pin PANEL_SW) 2-18

7. LVDS Backlight Panel header (5-pin LCD_BLKT_PANEL) 2-17

8. LVDS Panel VCC Power Selection jumper (6-pin VCC_PWR_SEL) 2-7

9. Chassis Fan header (4-pin CHA_FAN) 2-13

10. Clear RTC RAM (2-pin CLRTC) 2-6

11. LVDS Signal header (40-pin LVDS_EDP) 2-18

12. M.2 socket 3 2-15

13. SATA ports (7-pin SATA6G_1, SATA6G_2) 2-17

14. SATA Power connectors (4-pin SATA_PWR1, SATA_PWR2) 2-21

15. System Panel header (10-1 pin F_PANEL) 2-16

16. Chassis Intrusion header (4-1 pin CHASSIS) 2-13

17. Speaker header 2-23

18. Serial Port headers (10-1 pin COM4-6) 2-20

19. General Purpose Input/Output connector (10-pin GPIO_CON) 2-23

20. COM Debug header (6-1 pin COM_DEBUG) 2-21

21. PCI Express x1 slot 2-24

22. AT/ATX Mode Selection jumper (3-pin AT_ATX_SEL) 2-9

23. Stereo Speaker header (4-pin SPK_OUT) 2-19

24. I2C header (6-1 pin I2C) 2-22

25. Front Panel Audio header (10-1 pin F_AUDIO) 2-19

26. RTC Battery connector 2-22

27. TPM header (14-1 pin TPM) 2-20

28. COM1 Ring/+5V/+12V Selection jumper (6-pin COM1_SEL) 2-10

29. USB 2.0 header (5-1 pin USB_7) 2-14

30. M.2 Wi-Fi 2-15

N100I-EM-A

2-4

2.3 Central Processing Unit (CPU)

The motherboard comes with an onboard Intel® Celeron® Quad-core processor N100.

Intel®

N100

2.4 System memory

The motherboard comes with a Small Outline Dual Inline Memory Modules (SO-DIMM) slot

designed for a DDR4 (Double Data Rate 4) memory module.

CAUTION! A DDR4 memory module is notched differently from a DDR, DDR2,

or DDR3. DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR5

slot.

SO-DIMM_A

2-5

Chapter 2: Motherboard information

To remove a DIMM

2.4.1 Installing a DIMM

3

N100I-EM-A

2-6

2.5 Jumpers

1. Clear RTC RAM (2-pin CLRTC)

This header allows you to clear the CMOS RTC RAM data of the system

setup information such as date, time, and system passwords.

To erase the RTC RAM:

1. Turn OFF the computer and unplug the power cord.

2. Use a metal object such as a screwdriver to short the two pins.

3. Plug the power cord and turn ON the computer.

4. Hold down the <Del> key during the boot process and enter BIOS setup

to re-enter data.

NOTE: If the steps above do not help, remove the onboard battery and move

the jumper again to clear the CMOS RTC RAM data. After clearing the CMOS,

reinstall the battery.

+3V_BAT_NOTEST

GND

CLRTC

PIN 1

Connector type

HEADER 1x2p, 2.54mm pitch, S/T

2-7

Chapter 2: Motherboard information

2. Chassis intrusion header (4-1 pin_CHASSIS)

This header is for a chassis-mounted intrusion detection sensor or switch. Connect

one end of the chassis intrusion sensor or switch cable to this connector. The

chassis intrusion sensor or switch sends a low-level signal to this connector

when a chassis component is installed. The signal is then generated as a chassis

intrusion event.

+5VSB_ATX

O_CASEOPEN

GND

CHASSIS

PIN 1

Connector type

HEADER 4p, K2, 2.54mm pitch

Setting Pins

3V (Default) 1-2

5V 3-4

12V 5-6

3. LVDS Panel VCC Power Selection jumper (6-pin VCC_PWR_SEL)

12V5V

1

3V

(Default)

VCC_PWR_SEL

3

4

5

6

2

Connector type

HEADER 2 x 3p, 2.54mm pitch, S/T

N100I-EM-A

2-8

4. LVDS Panel Backlight Enable Signal Selection jumper (BKLTEN_SEL)

Pins

1-2 (Default) High Active

2-3 Low Active

1 2

2 3

High Active

(Default)

Low Active

BKLTEN_SEL

Connector type

HEADER 1x3p, 2.54mm pitch, S/T

2-9

Chapter 2: Motherboard information

5. AT/ATX Mode Selection jumper (3-pin AT_ATX_SEL)

In ATX mode (default), you will need to manually press the power button to

turn on the system power. In AT mode, the board will automatically turn on

when system power is connected.

Connector type HEADER 1x3p, 2.54mm pitch, S/T

21 2 3

ATX MODE

(Default)

AT MODE

AT_ATX_SEL

Pins Description

1-2 (Default) ATX mode

2-3 AT mode

N100I-EM-A

2-10

6. COM1 Ring/+5V/+12V Selection jumper (6-pin COM1_SEL)

The COM1 Ring/+5V/+12V Selection jumper allows you to select 5V or 12V

depending on your COM device.

Setting Pins

+12V 1-2

+5V 3-4

Ring (Default) 5-6

COM1_SEL

RI

(Default)

+5V+12V

12 34 56

Connector type HEADER 2x3p, 2.54mm pitch, S/T

2-11

Chapter 2: Motherboard information

2.6 Connectors

2.6.1 Rear panel connectors

3

1 2 5

9

4

7 863

1. DC Power connector. Insert the power adapter into this port.

NOTES:

• It only supports 12V DC input.

• The power adapter is purchased separately.

2. HDMI™ port. This port is for a High-Denition Multimedia Interface (HDMI™)

connector, and is HDCP compliant allowing playback of HD DVD, Blu-ray,

and other protected content.

3. Serial port connectors (COM). These ports connect modems, or other

devices that conform with serial specication.

4. LAN (RJ-45) ports. These ports allow Gigabit connection to a Local Area

Network (LAN) through a network hub.

LAN port LED indications

LAN port

Speed

LED

Activity Link

LED

Activity/Link LED Speed LED

Status Description Status Description

Off No link OFF 10Mbps connection

Orange Linked ORANGE 100Mbps connection

Orange (Blinking) Data activity GREEN 1Gbps connection

Orange (Blinking

then steady)

Ready to wake

up from S5 mode

5. Line Out port (lime). This port connects to a headphone or a speaker. In

the 4, and 5.1 channel congurations, the function of this port becomes Front

Speaker Out.

N100I-EM-A

2-12

6. Video Graphics Adapter (VGA) port. This 15-pin port is for a VGA monitor

or other VGA-compatible devices.

7. USB 3.2 Gen 1 (up to 5Gbps) ports (blue, Type-A). These Universal Serial

Bus (USB) ports are for USB 3.2 Gen 1 devices.

NOTE: We strongly recommend that you connect USB 3.2 Gen 1 devices to

USB 3.2 Gen 1 ports for faster and better performance from your USB 3.2 Gen

1 devices.

8. USB 2.0 ports. These Universal Serial Bus (USB) ports are for USB 2.0/1.1

devices.

9. Microphone port (pink). This port connects a microphone.

2-13

Chapter 2: Motherboard information

2.6.2 Internal connectors

CAUTION! Do not forget to connect the fan cable to the fan header. Insufcient

air flow inside the system may damage the motherboard components. This is

not a jumper! Do not place a jumper cap on the fan header!

1. Chassis Fan header (4-pin CHA_FAN)

Connect the fan cable to the fan header on the motherboard, ensuring that

the black wire of each cable matches the ground pin of the header.

CHA_FAN

FAN_PWM

FAN_IN

12V

GND

PIN 1

Connector type

WAFER HD 4p, 2.54mm pitch, S/T

2. USB 3.2 Gen 1 header (20-1 pin U32G1_34)

Connect a USB 3.2 Gen 1 module to this header for additional USB 3.2

Gen 1 front or rear panel ports. This header complies with USB 3.2 Gen

1 specications and provides faster data transfer speeds of up to 5 Gbps,

faster charging time for USB-chargeable devices, optimized power efciency,

and backward compatibility with USB 2.0.

+5V_USB_P34

S_U3RXDP3

S_U3TXDN3

GND

S_U2DP3

S_U2DP4

GND

S_U3TXDN4

S_U3RXDP4

+5V_USB_P34

PIN 1 PIN 19

PIN 18

S_U3RXDN3

GND

S_U3TXDP3

S_U2DN3

GND

S_U2DN4

S_U3TXDP4

GND

S_U3RXDN4

U32G1_34

Connector type

BOX HD 2x10p, K20, 2.0mm pitch

Page is loading ...

Asus N100I-EM-A User manual

Related papers

Other documents