Omron STC-HD133 HD93 Series User guide

No.16S058-01

1/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

16:9 Format 720p Color Camera

STC-HD133 Series

STC-HD93 Series

Users guide

No.16S058-01

2/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

Note.

All specifications are subject to change without prior notice.

Revisions

Rev

Date Changes Note

00 2016/06/24 New document

01 2017/07/03 Revised

Change the name of company

No.16S058-01

3/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

Table of Contents

1.

Introduction ............................................................................................ 4

2.

The requirement equipment to use the camera .................................. 4

3.

The camera settings setup method ...................................................... 6

3.1.

The camera setting with the push button .......................................................................................................... 6

3.2.

The camera setting with the remote controller .................................................................................................. 7

3.2.1.

The camera setting by the remote controller connects to 3.5mm stereo pin jack ........................................... 7

3.2.2.

The camera setting by SM06B-SRSS-TB (JST) connector on the board type camera .................................. 8

3.2.3.

The menu on the screen (OSD) with the remote controller ............................................................................. 9

3.3.

The control software users guide ..................................................................................................................... 20

3.3.1.

The basic operation for HD133Ctrl software ................................................................................................. 20

3.3.2.

The function descriptions for HD133Ctrl software ......................................................................................... 27

No.16S058-01

4/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

1. Introduction

This document describes for way to use the following cameras.

STC-HD133 series

[DVI output]

STC-HD133DV (C mount Cased type)

STC-HD133DV-B (C mount Board type)

STC-HD133DV-CS (CS mount Cased type)

STC-HD133DV-BCS (CS mount Board type)

[SDI output]

STC-HD133SDI (C mount Cased type)

STC-HD133SDI-B (C mount Board type)

STC-HD133SDI-CS (CS mount Cased type)

STC-HD133SDI-BCS (CS mount Board type)

STC-HD93 series

[DVI output]

STC-HD93DV (C mount Cased type)

STC-HD93DV-B (C mount Board type)

STC-HD93DV-CS (CS mount Cased type)

STC-HD93DV-BCS (CS mount Board type)

[SDI output]

STC-HD93SDI (C mount Cased type)

STC-HD93SDI-B (C mount Board type)

STC-HD93SDI-CS (CS mount Cased type)

STC-HD93SDI-BCS (CS mount Board type)

2. The requirement equipment to use the camera

The DVI output camera can connect to the HD monitor that has HDMI or DVI input port, to display the image on the

monitor.

The SDI output camera can connect to the HD monitor that has HD-SDI input port, to display the image on the monitor.

Below is the required equipment to use this camera:

A. The power adaptor or the power supply

Please provide +9Vdc to +15Vdc power to the camera. (12Vdc is recommended)

B. The monitor

For DVI output camera: 720P (1280x720 progressive) supports HD monitor with HDMI input port or DVI input port.

For SDI output camera: 720P (1280x720 progressive) supports HD monitor with HD-SDI input port.

No.16S058-01

5/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

C. The cable for the image

C-1.STC-HD133DV, HD93DV /-B/-CS/-BCS models

With HDIM input port on the monitor: HDMI – HDMI cable

With DVI input port on the monitor: HDMI – DVI cable

C-2.STC-HD133SDI, HD93SDI /-B/-CS/-BCS models

With HD-SDI input port on the monitor: BNC cable

D. The lens

Please use the C mount lens.

E. The remote controller or the communication tool.

The remote controller or the communication tool is required to change the camera settings.

The remote controller: RC-HD133

The communication tool: JIG-USB-HD

Fig. 1 STC-HD133DV / HD93DV rear panel Fig 2 STC-HD133DV-B / HD93DV-B rear board

Fig. 3 STC-HD133SDI / HD93SDI rear panel Fig. 4 STC-HD133SDI-B / HD93SDI-B rear board

Camera

settings Camera

settings

Power input

Image output

HDMI connector

Image output

HDMI connector

Power input

Image output

BNC connector Image output

BNC connector

No.16S058-01

6/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

3. The camera settings setup method

This camera has below three ways to setup the camera settings:

A. The camera setting with the push button

B. The camera setting with the remote controller (Option, separate accessories)

C. The camera setting with the communication (Option, separate accessories)

Two different type of the remote controller can use for the board type cameras (STC-HD**DV-B)

3.1. The camera setting with the push button

The white balance mode is changeable with the push button on the camera.

Push the button: Push to set white balance

Hold the button: Auto white balance

Fig 5 The push button location

No.16S058-01

7/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

3.2. The camera setting with the remote controller

The remote controller (RC-HD133) is the separate accessary.

3.2.1. The camera setting by the remote controller connects to 3.5mm stereo pin jack

A. It is necessary to assign the function for each button by the communication software.

Please check the default functions at “E. The remote controller function”.

B. The connector for the remote controller

C. The remote controller circuit diagram

D. The example remote controller

E. The function for the remote controller buttons

The below functions are assigned for SW-A to SW-F.

SW-A: Display the OSD menu

SW-B: Up cursor (Menu and select setting)

SW-C: Left cursor (select setting)

SW-D: Execute the selected setting

SW-E: Right cursor (Select setting)

SW-F: Down cursor (Menu and select setting)

Tip

GND

SW-A SW-B SW-C SW-D SW-E SW-F

1 2

R1

1.8K R2

3.3K R3

4.7K R4

10K R5

27K

SW-A

SW-B

SW-D

SW-C SW-E

SW-F

No.16S058-01

8/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

3.2.2. The camera setting by SM06B-SRSS-TB (JST) connector on the board type camera

A. It is necessary to assign the function for each button by the communication software.

Please check the default functions at “E. The remote controller function”.

B. The connector for the remote controller

Note: The connector location for SDI model is same.

C. The remote controller circuit diagram

1 2 1 2 1 2

1

2

3

4

5

6

SW11

SW21

SW12 SW13

SW22 SW23

SW31 SW32 SW33

ROW2

ROW3

ROW1

C

OLUMN2

C

OLUMN3

C

OLUMN1

D11

D21

D31

D12

D22

D32

D13

D23

D33

D. The example remote controller

The function for the remote controller buttons

The below functions are assigned for SW-11 to SW-13.

SW-11: Page (-)

SW-13: Page (+)

Any function dose not assign for the SW-12, SW-21 to SW-33.

Please assign the function by the communication software if it is necessary.

SW-11 SW-13SW-12

SW-21 SW-23SW-22

SW-31 SW-33SW-32

No.16S058-01

9/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

3.2.3. The menu on the screen (OSD) with the remote controller

A. Page 1

1) ALC

Selects enable or disable for the auto light compensation. (Default: ON)

a) ON

Enables the auto light compensation.

It is necessary to select “AUTO” for SHUTTER and GAIN then set the target brightness level.

b) OFF

Disables the auto light compensation.

It is necessary to set the exposure time for SHUTTER and gain for GAIN.

2) GAIN

Selects the gain control mode from below two modes. (Default: AUTO 65)

a) AUTO

The AGC (Auto gain control) mode

It is necessary to set the target brightness level. This target brightness level is common for the auto

shutter.

b) FIXED

The fixed gain control mode.

It is necessary to set the fix gain from 0 (0dB) to 511 (18.345dB).

3) SHUTTER

Selects the shutter control mode from below two modes. (Default: AUTO 65)

a) AUTO

The auto shutter control mode.

It is necessary to set the target brightness level. This target brightness level is common for the auto

shutter.

b) FIXED

The fixed shutter control mode.

It is necessary to set the fix shutter from 0 (1/60s) to 690 (1/100,000s).

PAGE 1 2 3 4 5 6

ALC ON

GAIN AUTO 065

SHUTTER AUTO 065

GAMMA PRESET

OFFSET 000

CONTRAST 128

SHARPNESS H04 V06 CORING03

MIRROR OFF

No.16S058-01

10/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

4) GAMMA

Sets the gamma (Default: PRESET(0.70))

The gamma setting selects from PRESET(0.70), 0.30, 0.45, 0.50, 0.60, 0.70, 0.80, 0.90 and 1.00.

5) OFFSET

Sets the offset of the image. (Default: 0)

6) CONTRAST

Sets the contrast of the image. (Default: 128)

7) SHARPNESS

Sets the sharpness (edge enhancement) of the image. (Default: 0)

a) H (Default: 4)

Sets the horizontal sharpness

The image becomes sharper image when increasing this setting.

b) V (Default: 6)

Sets the vertical sharpness.

The image becomes sharper image when increasing this setting.

c) CORING (Default: 3)

The noise level also emphasizes when using the sharpness function.

The SN ratio deteriorate for the other than the edge parts is prevented by cutting the signal level

that smaller than this setting.

The image becomes the soft image if this setting sets too large.

8) MIRROR

Selects the flip image setting for the video output from below two flip modes. (Default: OFF)

a) OFF

The standard image (No flip image) is output.

b) ON

The horizontal flip image is output.

No.16S058-01

11/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

B. Page 2

1) WB

Selects the white balance mode from below two modes. (Default: AUOT G0000)

a) AUTO

The auto white balance.

The Green gain is adjustable by Gxxx.

b) MANUAL (Default: R199, G000 and B215)

The manual white balance with “Rxx” R gain, “Bxx” B gain and “Gxx” G gain.

The Red gain is adjustable by “Rxxx”. The Green gain is adjustable by “Gxxx”. The Blue gain is

adjustable by “Bxxx”

PAGE 1 2 3 4 5 6

WB AUTO G000

No.16S058-01

12/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

C. Page 3

1) GRAPHICS

Selects enable or disable for the line makers and the shadow mask display. (Default: ON)

a) ON

The line markers and the shadow mask can be display.

The line makers display enable or disable is selecting at “LINE”

The shadow mask display enable or disable is selecting at “SHADOW”.

Sets the color, the size (thickness) and the position for the line makers.

Sets the grade, the position for the shadow mask.

b) OFF

The line markers and the shadow mask do NOT display.

2) LINE

Selects enable or disable for the Line markers display (Default: ON)

a) ON

Two horizontal and two vertical line makers can be display.

It is necessary to set “ON” at GRAPHICS to display the line makers.

The color, the size (thickness) and the position are selectable for the individual line maker.

The line maker does not display when the size is “0”.

“0” position for the horizontal lime maker is top and “0” position for the vertical line maker is the left

end.

The color is selectable from Black, White, Red, Green, Blue, Cyan, Magenta, Yellow, Amber, Pink,

Light Green, Purple and Gray.

b) OFF

The line makers do not display.

PAGE 1 2 3 4 5 6

GRAPHICS ON

LINE ON

LINE1 H POS 0000 SIZE 0000

COLOR BLACK

V POS 0000 SIZE 0000

COLOR BLACK

LINE2 H POS 0000 SIZE 0000

COLOR BLACK

V POS 0000 SIZE 0000

COLOR BLACK

No.16S058-01

13/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

D. Page 4

1) GRAPHICS

Selects enable or disable for the line makers and the shadow mask display. (Default: ON)

This function in the page3 and in the page4 is the same function.

2) SHADOW

Selects enable or disable for the shadow mask display (Default: ON)

a) ON

The shadow mask can be display.

It is necessary to set “ON” at GRAPHICS to display the line makers.

b) OFF

The shadow mask does not display..

3) Shadow mask settings

a) GRADE

Sets the grade of the shadow mask.

No grade when setting “0” and 100% Black masking when setting “255”.

b) SHADOW H T

Sets the horizontal position for the top area of the shadow mask.

c) SHADOW H B

Sets the horizontal position for the bottom area of the shadow mask.

d) SHADOW V L

Sets the vertical position for the left area of the shadow mask.

e) SHADOW V R

Sets the vertical position for the right area of the shadow mask.

PAGE 1 2 3 4 5 6

GRAPHICS ON

SHADOW ON GRADE 000

H T 0000 B 720

V L 0000 R 1280

CIRCLE ON

RADIUS 000 SIZE 000

H POS 0960

V POS 0540

COLOR BLACK

No.16S058-01

14/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

Shadow mask

Vertical line1

Vertical line2

Horizontal line1

Horizontal line2

LINE1 V POS

LINE2 V POS

LINE1 H POS

LINE2 H POS

SHADOW H T

SHADOW H B

SHADOW V L

SHADOW V R

No.16S058-01

15/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

4) CIRCLE

Selects enable or disable for the circle maker display (Default: ON)

a) ON

The circle mask can be display.

It is necessary to set “ON” at GRAPHICS to display the line makers.

b) OFF

The circle maker does not display.

5) Circle maker settings

Sets the radius, the size (thickness), the center position and the color for the circle maker.

a) RADIUS

Sets the radius for the circle.

The circle is the filled circle when setting “000”.

b) SIZE

Sets the size (thickness) for the circle.

The circle maker does not display when the size is “0”.

c) H POS

Sets the horizontal center position for the circle.

d) V POS

Sets the vertical center position for the circle.

e) COLOR

Sets the color for the circle.

The color is selectable from Black, White, Red, Green, Blue, Cyan, Magenta, Yellow, USER0, USER1,

USER2, USER3, USER4, USER5, USER6 and USER7.

USER0 to USER7 are necessary to select wit the communication software.

H POS,

V POS

RADIUS

COLOR

SIZE

No.16S058-01

16/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

E. Page 5

1) FPS

Sets the frame rate for the video output from below three frame rates. (Default: 59.94)

a) 59.94

The image format and the frame rate is 720p 59.94Hz.

b) 50

The image format and the frame rate is 720p 50Hz.

c) 60

The image format and the frame rate is 720p 60Hz.

2) OSD SIZE

Sets the character size for OSD. (Default: LARGE)

a) LARGE

OSD display with the large characters.

b) SMALL

OSD display with the small characters.

PAGE 1 2 3 4 5 6

FPS 59.94

OSD SIZE LARGE

PROFILES PRESET00

PATTERNS OFF

No.16S058-01

17/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

3) PROFILE

Sets the Preset data from below twenty eight preset data. (Default: PROFILE00 (Standard image))

a) PROFILE00

The standard image is output.

b) PROFILE01

The high contrast image is output.

c) PROFILE02 to PROFILE27

The negative image from below twenty six negative images, is output.

PROFILE02 PROFILE03 PROFILE04 PROFILE05 PROFILE06 PROFILE07

PROFILE08 PROFILE09 PROFILE10 PROFILE11 PROFILE12 PROFILE13

PROFILE14 PROFILE15 PROFILE16 PROFILE17 PROFILE18 PROFILE19

PROFILE20 PROFILE21 PROFILE22 PROFILE23 PROFILE24 PROFILE25

PROFILE26 PROFILE27

10

No.16S058-01

18/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

4) PATTERNS

Selects the output signal from below four output signals. (Default: OFF (Image out))

a) OFF

The video is output from the camera.

b) GRAY

The gray scale test pattern is output from the camera.

c) COLOR

The color test pattern is output from the camera.

d) GRAY+COLOR

The color pattern (Top) + the gray scale test pattern (Bottom) is output from the camera.

No.16S058-01

19/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

F. Page 6

1) EEPROM

The camera settings in the page1 to page5 can be saved into the camera as the camera default settings.

a) SAVE

When executing the “SAVE”, the confirmation message “ARE YOU OK?” is displayed.

When executing again, the settings save into the camera.

The message “COMPLETE” is displayed after the settings are saved.

PAGE 1 2 3 4 5 6

EEPROM SAVE

No.16S058-01

20/49

STC-HD133 Series (STC-HD133DV / STC-HD133SDI) /

STC-HD93 Series (STC-HD93DV / STC-HD93SDI) Users guide

3.3. The control software users guide

3.3.1. The basic operation for HD133Ctrl software

A. Menu function

a. File

1) Save As [DSP’s EEPROM]

The EEPROM data for the current DSP preset saves to the file in the PC.

The settings in “DSP:” started windows are saved to the file.

The current DSP preset can check at “uCOM:Other” window.

It is necessary to change the DSP preset at “uCOM:Other” window and save to the file if All DSP

settings save to the file.

The camera has 28 of the DSP presets.

2) Save As [uCOM’s EEPROM]

The EEPROM data for the uCOM saves to the file in the PC.

The settings in “uCOM:” started windows are saved to the file.

3) Open [DSP’s EEPROM]

The DSP Preset EEPROM data saves to the EEPROM on the camera from the file in the PC.

The EEPROM data saves to the current DSP preset. Please check the current DSP preset at

“uCOM:Other” window before select this menu function.

4) Open [uCOM’s EEPROM]

The uCOM EEPROM data saves to the EEPROM on the camera from the file in the PC.

5) Exit

Close HD133Ctrl software.

Page is loading ...

Omron STC-HD133 HD93 Series User guide

Omron STC-HD133 HD93 Series User guide

Related papers

Other documents