INSTALLATION & MAINTENANCE MANUAL
PWRCC
These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following product:
PWRCC
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location
for installation
• This product is for indoor use only
• This product is Class II double insulated
• This product is IP20 rated
INSTALLATION
• Provide power to the required point of installation
• Cut a 210 x 250mm hole in the mounting surface, ensuring not to infringe with any
joists, gas/water pipes or electrical cables
• Attach the side brackets to the luminaire (see Fig. 1)
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid the installation of the following product:
PWRCC
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
• This product is for indoor use only
• This product is Class II
• This product is IP20 rated
INSTALLATION
• Provide power to the required point of installation
• Cut a 210 x 250mm hole in the mounting surface, ensuring not to infringe with any joists, gas/water
pipes or electrical cables
• Attach the side brackets to the luminaire (see Fig. 1)
Fig. 1
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid the installation of the following product:
PWRCC
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
• This product is for indoor use only
• This product is Class II
• This product is IP20 rated
INSTALLATION
• Provide power to the required point of installation
• Cut a 210 x 250mm hole in the mounting surface, ensuring not to infringe with any joists, gas/water
pipes or electrical cables
• Attach the side brackets to the luminaire (see Fig. 1)
Fig. 1
Fig.1
• Insert the luminaire into the cut-out ensuring the mains cable is pulled out of the wall,
and fix the luminaire to the wall using suitable screws (not provided) (see Fig. 2)
• Cover the bracket screws and the margins of the luminaire with plaster and paint
(see Fig. 3)
• Unscrew the terminal cover
• Connect the luminaire to the mains supply ensuring the correct polarity is observed
(see Fig. 4): L - Live (Brown) and N - Neutral (Blue)
• Insert the luminaire into the cut-out ensuring the mains cable is pulled out of the wall, and fix the
luminaire to the wall using suitable screws (not provided), see Fig. 2
Fig. 2
• Cover the bracket screws and the margins of the luminaire with plaster and paint (see Fig. 3)
Fig. 3
• Unscrew the terminal cover
• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 4):
L - Live (Brown) and N - Neutral (Blue).
• Insert the luminaire into the cut-out ensuring the mains cable is pulled out of the wall, and fix the
luminaire to the wall using suitable screws (not provided), see Fig. 2
Fig. 2
• Cover the bracket screws and the margins of the luminaire with plaster and paint (see Fig. 3)
Fig. 3
• Unscrew the terminal cover
• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 4):
L - Live (Brown) and N - Neutral (Blue).
Fig.2
Fig.3
GENERAL
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which
may damage the product.
This product is dimmable dependent on lamp type.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
Fig. 4
• Insert a suitable GU10 lamp and clip the lamp into the luminaire
• Switch on and check for correct operation
GENERAL
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is dimmable dependent on lamp type.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
WARRANTY
This product has a warranty of 2 years from the date of purchase. Failure to install this product in accordance
with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of
purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
230V, IP20, Class II, Dim, Indoor only
AVMAY21_V1
Fig.4
• Insert a suitable GU10 lamp and clip the lamp into the
luminaire
• Switch on and check for correct operation
AVMAY21_V1
WARRANTY
This product has a warranty of 2 years from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation costs
associated with the replacement product. Your statutory rights are not affected.
ML Accessories reserve the right to alter product specification without prior notice.
141
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ML Accessories 12DCIP40 User manual
-
-
-
ML Accessories DGZ10CBR User manual
-
-
-
-
-
-
Other documents
-
Knightsbridge CSPT1BC User manual
-
-
-
-
-
Knightsbridge TRIBCCW User manual
-
-
Knightsbridge AMA3TSBC User manual
-
-