ML Accessories LEDBATW44EM User manual

ML Accessories
Brand
ML Accessories
Model
LEDBATW44EM
Type
User manual

This manual is also suitable for

ML Accessories LEDBATW44EM is a non-dimmable LED luminaire with an IP20 rating, suitable for indoor use only. It has a Class I construction, meaning it requires an earth connection. The luminaire can be used for emergency lighting, with a duration of approximately 1 hour. It has a built-in battery that provides power in the event of a mains power failure. The luminaire can be either non-maintained or maintained, depending on the wiring configuration. It is also easy to install, with a simple fixing bracket that allows for even weight distribution.

ML Accessories LEDBATW44EM is a non-dimmable LED luminaire with an IP20 rating, suitable for indoor use only. It has a Class I construction, meaning it requires an earth connection. The luminaire can be used for emergency lighting, with a duration of approximately 1 hour. It has a built-in battery that provides power in the event of a mains power failure. The luminaire can be either non-maintained or maintained, depending on the wiring configuration. It is also easy to install, with a simple fixing bracket that allows for even weight distribution.

52
INSTALLATION & MAINTENANCE MANUAL
LEDBATW_EM SERIES
IP
20
230V
50Hz
These instructions should be read carefully and retained after installation by the end user for future
reference and maintenance.
These instructions should be used to aid installation of the following products:
LEDBATW44EM / LEDBATW50EM
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• Installation of this luminaire should only be carried out by a qualified electrician or competent
person to the latest Building and current IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the
rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for
installation
• This product is Class I and requires an earth
• This product series is IP20 rated
• This product is non-dimmable
• Provide power to the required point of installation
• Remove the base fixing brackets and use as a template - ensure the base mounting brackets are
evenly spaced in order to distribute the weight evenly
• Drill the holes ensuring not to infringe with any joists, gas / water pipes or electrical cables
• Remove panel on the rear of the luminaire to gain access to the mains terminal block
(please see Fig 1)
• Ensuring correct polarity is observed, carefully wire as shown in Fig 2-4
Non maintained operation
Fig 1
Fig 2
LEDBAT__EMseries
Theseinstructionsshouldbereadcarefullyandretainedafterinstallationbytheenduserforfuturereferenceand
maintenance.
Theseinstructionsshouldbeusedtoaidinstallationofthefollowingproducts:
LEDBAT44EM,LEDBAT50EM
SAFETY
• Installationofthisluminaireshouldonlybecarriedoutbyaqualifiedelectricianorcompetentpersontothe
latestBuildingandcurrentIEEWiringRegulations(BS7671)
• Pleaseisolatemainspriortoinstallation/maintenance
• Checkthetotalloadonthecircuit(includingwhenthisluminaireisfitted)doesnotexceedtheratingofthe
circuitcable,fuseorcircuitbreaker
• PleasenotetheIP(IngressofProtection)ratingofthisluminairewhendecidingthelocationforinstallation
• ThisproductisClassIandrequiresanearth
• ThisproductseriesisIP20rated
• Thisproductisnon-dimmable
INSTALLATION
• Providepowertotherequiredpointofinstallation
• Removethebasefixingbracketsanduseasatemplate-ensurethebasemountingbracketsareevenlyspaced
inordertodistributetheweightevenly
• Drilltheholesensuringnottoinfringewithanyjoists,gasorwaterpipesorelectricalcables
• Removepanelontherearoftheluminairetogainaccesstothemainsterminalblock(pleaseseefig1)
Fig1
• Ensuringcorrectpolarityisobserved,carefullywireasshowninFig2
Fig2
• Ontheoppositeendoftheluminaireconnectthebatterytotheinverterviatheplugandsocket
• Fixluminairetobasemountingfixing
• SwitchonpowersupplyandensurethatthegreenLEDisilluminated
GENERAL
Theunitshouldberecycledinthecorrectmannerwhenitreachestheendofitslife.Checklocalauthoritiesforwhere
facilitiesexist.
Neutral(blue)
Live(brown)
Earth(yellow/green)
AC
Removescrews
L
E
N
SwitchedLive
Neutral(blue)
PermanentLive(brown)
Earth(yellow/green)
AC
Removescrews
1
E
N
2
’
SwitchedLive
Neutral(blue)
PermanentLive(brown)
Earth(yellow/green)
1
E
N
2
’
GENERAL
WARNING
The unit should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.
If the batteries have been left in a discharged state for a long period of time, we recommend that one
or more charge and discharge cycles are required, this should restore the battery to its full capacity.
The batteries in this fitting are Nickel Cadmium and must be disposed of correctly. Please contact
the local authorities for the disposal of this toxic waste.
Subject to the surface foundation material, ensure the correct fixings are used.
When installing ensure the indicator LED can be seen.
Approximately 1/6 of the fitting will be illuminated when in emergency mode.
This product must be disconnected from the circuit if subjected to any high voltage or insulation
resistance testing. Irreparable damage will occur if this instruction is not followed.
Recommended routine test procedure in accordance with BS5266
Daily check – check that the status GREEN LED indicator is illuminated.
Monthly functional test – simulate a mains supply failure for approx. 30 secs by operation of key
switch or switching off a circuit breaker. Ensure normal supply is restored after test and the indicator
status LED is illuminated.
Twice yearly conduct a one hour duration test - simulate a mains supply failure for one hour
continuous test by operation of key switch or switching off circuit breaker. Ensure normal supply is
restored after test and the indicator status LED is illuminated.
• At the opposite end of the luminaire, connect the battery to the inverter via the plug and socket
• Fix luminaire to base mounting brackets
• Switch on power supply and ensure that the green LED is illuminated
Maintained operation
Switched maintained operation
Fig 3
Fig 4
LEDBAT__EMseries
Theseinstructionsshouldbereadcarefullyandretainedafterinstallationbytheenduserforfuturereferenceand
maintenance.
Theseinstructionsshouldbeusedtoaidinstallationofthefollowingproducts:
LEDBAT44EM,LEDBAT50EM
SAFETY
• Installationofthisluminaireshouldonlybecarriedoutbyaqualifiedelectricianorcompetentpersontothe
latestBuildingandcurrentIEEWiringRegulations(BS7671)
• Pleaseisolatemainspriortoinstallation/maintenance
• Checkthetotalloadonthecircuit(includingwhenthisluminaireisfitted)doesnotexceedtheratingofthe
circuitcable,fuseorcircuitbreaker
• PleasenotetheIP(IngressofProtection)ratingofthisluminairewhendecidingthelocationforinstallation
• ThisproductisClassIandrequiresanearth
• ThisproductseriesisIP20rated
• Thisproductisnon-dimmable
INSTALLATION
• Providepowertotherequiredpointofinstallation
• Removethebasefixingbracketsanduseasatemplate-ensurethebasemountingbracketsareevenlyspaced
inordertodistributetheweightevenly
• Drilltheholesensuringnottoinfringewithanyjoists,gasorwaterpipesorelectricalcables
• Removepanelontherearoftheluminairetogainaccesstothemainsterminalblock(pleaseseefig1)
 
Fig1
• Ensuringcorrectpolarityisobserved,carefullywireasshowninthebelowdiagrams
Fig2(Nonmaintainedoperation)
Fig3(maintainedoperation)
SwitchedLive
Neutral(blue)
PermanentLive(brown)
Earth(yellow/green)
AC
Removescrews
1
E
N
2
’
SwitchedLive
Neutral(blue)
PermanentLive(brown)
Earth(yellow/green)
1
E
N
2
’
LEDBAT__EMseries
Theseinstructionsshouldbereadcarefullyandretainedafterinstallationbytheenduserforfuturereferenceand
maintenance.
Theseinstructionsshouldbeusedtoaidinstallationofthefollowingproducts:
LEDBAT44EM,LEDBAT50EM
SAFETY
• Installationofthisluminaireshouldonlybecarriedoutbyaqualifiedelectricianorcompetentpersontothe
latestBuildingandcurrentIEEWiringRegulations(BS7671)
• Pleaseisolatemainspriortoinstallation/maintenance
• Checkthetotalloadonthecircuit(includingwhenthisluminaireisfitted)doesnotexceedtheratingofthe
circuitcable,fuseorcircuitbreaker
• PleasenotetheIP(IngressofProtection)ratingofthisluminairewhendecidingthelocationforinstallation
• ThisproductisClassIandrequiresanearth
• ThisproductseriesisIP20rated
• Thisproductisnon-dimmable
INSTALLATION
• Providepowertotherequiredpointofinstallation
• Removethebasefixingbracketsanduseasatemplate-ensurethebasemountingbracketsareevenlyspaced
inordertodistributetheweightevenly
• Drilltheholesensuringnottoinfringewithanyjoists,gasorwaterpipesorelectricalcables
• Removepanelontherearoftheluminairetogainaccesstothemainsterminalblock(pleaseseefig1)
 
Fig1
• Ensuringcorrectpolarityisobserved,carefullywireasshowninthebelowdiagrams
Fig2(Nonmaintainedoperation)
Fig3(maintainedoperation)
SwitchedLive
Neutral(blue)
PermanentLive(brown)
Earth(yellow/green)
AC
Removescrews
1
E
N
2
’
SwitchedLive
Neutral(blue)
PermanentLive(brown)
Earth(yellow/green)
1
E
N
2
’
ML Accessories Limited
LU5 5TA
www.mlaccessories.co.uk SBSEP17_V4
WARRANTY
This product has a warranty of 5 years (excluding battery) from date of purchase. Failure to install this
product in accordance with the current edition of the IEE Wiring regulations, improper use or removal
of the batch codes will invalidate the warranty. If this product should fail within its warranty period
it should be returned to the place of purchase for a free of charge replacement. ML Accessories
does not accept responsibility for any installation costs associated with the replacement product.
Your statutory rights are not affected. ML Accessories reserve the right to alter product specification
without prior notice.
TEST RECORD SHEET
FIRST YEAR SECOND YEAR THIRD YEAR FOURTH YEAR FIFTH YEAR
MONTH TEST
SIGNED DATE SIGNED DATE SIGNED DATE SIGNED DATE SIGNED DATE
1FUNCTIONAL
2FUNCTIONAL
3FUNCTIONAL
4FUNCTIONAL
5FUNCTIONAL
61 HOUR
7FUNCTIONAL
8FUNCTIONAL
9FUNCTIONAL
10 FUNCTIONAL
11 FUNCTIONAL
12 3 HOUR
Installed by: Installation date:
Contact number:
Annual full three hour duration test - conduct a three hour continuous duration test. Simulate a
mains supply failure for three hour continuous test by operation of key switch or switching off circuit
breaker. Ensure normal supply is restored after test and the indicator status LED is illuminated.
If the luminaire fails any of the above tests, please consult a qualified electrician. See below for test
record sheet.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ML Accessories LEDBATW44EM User manual

ML Accessories
Brand
ML Accessories
Model
LEDBATW44EM
Type
User manual
This manual is also suitable for

ML Accessories LEDBATW44EM is a non-dimmable LED luminaire with an IP20 rating, suitable for indoor use only. It has a Class I construction, meaning it requires an earth connection. The luminaire can be used for emergency lighting, with a duration of approximately 1 hour. It has a built-in battery that provides power in the event of a mains power failure. The luminaire can be either non-maintained or maintained, depending on the wiring configuration. It is also easy to install, with a simple fixing bracket that allows for even weight distribution.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents