Modern Forms PD-64834 Chaos Operating instructions

Modern Forms
Brand
Modern Forms
Model
PD-64834 Chaos
Type
Operating instructions
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 1
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64834
HARDWARE
A
Wire Connector
Qty: 3 pcs+ 1 Extra
7EAC112201
P3
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
B
Junction Box Screw
Qty: 2 pcs + 1 Extra
7MPF0415C2
#8-32x5/8 SS
D
Plastic Anchor
Qty: 3 pcs + 1 Extra
7TDD082401
E
Wood Screw
Qty: 3 pcs + 1 Extra
7MPF2204J2
C
Mounting Screw
Qty: 1 Extra
7MPF0412S1 (AL)
7MPF0412S1BK (BK)
4MPF0412S2BB1 (AB)
5/32-32x1/2
G0
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 2
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE Fig. 1
3. Remove the mounting screw (C) from the xture.
4. Drill holes in the wall aligned with the key holes located in the mounting back plate, insert the plastic anchor (D).
5. Secure back plate to the junction box using junction box screws (B), fasten it to the wall using wood screw (E).The side of the mounting
plate marked “GND” must face out.
6. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling the wire as desired. Make sure the wires are the
same length.
a. Retract these wires close to a desirable length to within the canopy before securing the xture in place. Using the cable gripper to
adjust more than 18” of wire length is not desirable.
b. Warning: Shortening these cables without professional help or electronic background is not advisable. Any modications to the xture
will result in voiding the warranty of the product.
CONNECTING THE WIRES Fig. 2
7. Connect the driver input wires with junction box wires as shown in Fig.2, making sure that all wire connectors (A) are secured. If your outlet
box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to
the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
8. Hook the safety cords to the back plate.
9. Place the xture over the back plate and secure it with mounting screws (C).
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
FIG.1
A
B
D
E
C
Junction Box
Ground Wire
Wire Connector
Plastic Anchor
Wood Screw
Back Plate
Cable Gripper
Adjust the xture wire
length by pushing the
cable gripper on the
canopy and pulling the
wire as desired
Push Up
Safety Cords
Mounting Screw
Junction Box
Screw Driver 3 1/2”LX2 3/8”W
X1 1/4”H
Back Plate Dimensions
7MBC2222002
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64834
8 ⁄”
1 ⁄”
8 ⁄”
1 ¾”
G0
0RGHUQ)RUPV
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
+HDGTXDUWHUV(DVWHUQ'LVWULEXWLRQ&HQWHU
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
:HVWHUQ'LVWULEXWLRQ&HQWHU
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
1
INSTALLATION INSTRUCTION
/('3HQGDQW
PD-64861
+$5':$5(
$
Wire Connector
Qty: pcs+ 1 Extra
7EAC112201
P3
:$51,1*
- Read all instructions before installing.
ations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
$9(57,66(0(17
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
$'9(57(1&,$
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
mas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
%
Junction Box Screw
Qty: 2 pcs + 1 Extra
7MPF0415C2
#8-32x5/8 SS
&
Mounting Screw
Qty: 3 pcs +1 Extra
7MPF0412S1 (AL)
7MPF0412S1BK (BK)
4MPF0412S2BB1 (AB)
5/32-32x1/2
'
Plastic Anchor
Qty: 3 pcs + 1 Extra
7TDD082401
(
Wood Screw
Qty: 3 pcs + 1 Extra
7MPF2204J2
)
Iron Hexagon Nuts
Qty: 8 pcs + 1 Extra
7MPM080402ZN (AL)
7MPM080402BK (BK)
7MPM080402BB1 (AB)
m8x1
G0 
0RGHUQ)RUPV
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
+HDGTXDUWHUV(DVWHUQ'LVWULEXWLRQ&HQWHU
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
:HVWHUQ'LVWULEXWLRQ&HQWHU
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
2
$
,
)
'
(
*
+%
&
Junction Box
Back Plate
Safety Cords
Hexagon nuts
Gasket
Driver
3 1/2”Lx2 3/8”WX 1 1/4”H
Lamp Body
Lamp Body
Lamp Body Lamp Body
Lamp Body
Lamp Body
Assembly
Assembly
Assembly Assembly
Assembly
Assembly
Lamp Canopy
Lamp Body Assembly
Qty: 4pcs
Qty: 1pcs
Ground Wire
Wire Connector
Nuts
Iron Hexagon Nuts
Plastic Anchor
Wood Screw
Junction Box
Screw
Wood Screw
INSTALLATION INSTRUCTION
/('3HQGDQW
PD-64861
G0
),*
),*
),*
),*
Cable Gripper
length by pushing the
cable gripper on the
canopy and pulling the
wire as desired
Push Up

0RGHUQ)RUPV
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
+HDGTXDUWHUV(DVWHUQ'LVWULEXWLRQ&HQWHU
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
:HVWHUQ'LVWULEXWLRQ&HQWHU
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
3
35(3$5$7,21
for installation.
02817,1*7+(),;785(
4. Drill holes in the wall aligned with the key holes located in the mounting back plate, insert the plastic anchor (D).
5. Secure back plate to the junction box using junction box screws (B), fasten it to the wall using wood screw (E).The side of the mounting
plate marked “GND” must face out.
6. Connect the two lamp body components with hexagon nuts (F) and nuts (I) (Fig. 3).
7. Then, in turn the third, the fourth Lamp body assembly, after installed, like a circle (Fig. 4).
8. Steel cable through the Lamp canopy cable-gripper. Then braided wire line buckle through the gasket (G) and (H) hexagonal nut fastening
at the Lamp canopy.
9. Braided wire can be divided into two groups, the total of two groups, one group connection one drive with wire connectors (A), another
group connection another drive with wire connectors (A).
length.
adjust more than 18” of wire length is not desirable.
will result in voiding the warranty of the product.
&211(&7,1*7+(:,5(6
11. Connect the driver input wires with junction box wires as shown in Fig.2, making sure that all wire connectors (A) are secured. If your outlet
the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
12. Hook the safety cords to the back plate.
%DFN3ODWH'LPHQVLRQV
7MBC252008
INSTALLATION INSTRUCTION
/('3HQGDQW
PD-64861
G0
*
Hexagon Nuts
Qty: 4 pcs + 1 Extra
7MPM0904C1
1/8-27x1/8
+
Gasket
Qty: 4 pcs + 1 Extra
7MPH1610A1
,
Nut
Qty: 8pcs + 1 Extra
4MBA161208BA (AL)
4MBA161208BK (BK)
4MBA161208BB2 (AB)
)L[WXUH:LUHV
Black or
Smooth
)L[WXUH:LUHV
White or
Ribbed
)L[WXUH:LUHV
Bare wire
(Ground)
+RXVH:LUHV
Black
(Hot)
+RXVH:LUHV
White
(Neutral)
+RXVH:LUHV
Green or Bare Copper
(Ground)
)LJ:LULQJ
9 ½”
1 ¾”

14. Please follow these if shortening the wire is needed. Take note or take picture of how
the wires are being connected and label each wire clearly. Using the gure X as given
below as reference( FIG.6).
0RGHUQ)RUPV
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
+HDGTXDUWHUV(DVWHUQ'LVWULEXWLRQ&HQWHU
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
:HVWHUQ'LVWULEXWLRQ&HQWHU
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
4
INSTALLATION INSTRUCTION
/('3HQGDQW
PD-64861
G0 
Black -
Hot
White -
Neutral
Black
- Hot
White -
Neutral
 
Black -
Hot
White -
Neutral
,QWHUQDO :LUH
([WHUQDO
Braided
:LUH
,QWHUQDO :LUH
([WHUQDO
Braided
:LUH
Driver
'LPPHU
˄
Purple
˅
'LPPHU
˄
Ashy
˅
Driver
 
Input
Out
SXW
Out
SXW
Input
([WHUQDO
Braided
:LUH
,QWHUQDO :LUH
([WHUQDO
Braided
:LUH
,QWHUQDO :LUH
),*
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Modern Forms PD-64834 Chaos Operating instructions

Modern Forms
Brand
Modern Forms
Model
PD-64834 Chaos
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents