Nucraft Merino T-Shape Installation Instructions Manual

Brand
Nucraft
Model
Merino T-Shape
Type
Installation Instructions Manual
Merino Casegood Installation Instructions
Rev B – 6/17/16
Before Beginning Installation
•Read through the entire instruction thoroughly
•A minimum of 2 people are required for this
assembly
•These instructions reflect typical assemblies; They
may not match your specific configuration
Required Tools & Hardware
Drill Driver
#2- #3 Phillips Bit
#2 Square Bit
3/8” Nut Driver
Laser Level
5/16” Wrench
1
2
3
4
5
Merino Free Standing
Merino Free Standing Exploded
1
2 4
5
3
1. Freestanding Desk
2. Work Surface
3. Lateral File Pedestal
4. Box, Box, File Pedestal
5. Tack Board
6. Overhead
7. Tower
6
7
Merino U-Shape
Merino U-Shape Exploded
1
2
6
4
5
1. Desk
2. Work Surface
3. Lateral File Pedestal
4. Box, Box, File Pedestal
5. Tack Board
6. Overhead
7. Tower
8. Access Panel
9. Corner Support
10.Bridge
7
8
9
10
Merino L-Shape
Merino L-Shape Exploded
6
2
5
4
1
1. Desk
2. Work Surface
3. Lateral File Pedestal
4. Box, Box, File Pedestal
5. Tack Board
6. Overhead
7. Overhead Hood
8. Corner Support
9. Power Option
7
8
9
Merino T-Shape
Merino T-Shape Exploded
1
2
3
4
5
6
7
8
9
1. Desk
2. Work Surface
3. Lateral File Pedestal
4. Box, Box, File Pedestal
5. Tack Board
6. Overhead
7. Overhead Hood
8. Access Panel
9. Tower
Merino | 12
Step 1
Installing the Credenza
Locate the Pedestals and set in
place. Level.
Align work surface with mitered
edge on pedestal(s). Attach
using &
If station has additional work
surfaces, attach those the same
way and connect using mending
plates and screws
3 5
3 5
4
Merino | 13
Step 2
Attaching Corner Support
Install connector pins 1 to the
work surface.
Lower the work surface onto
the corner support, aligning
the pins with the
corresponding holes in the
corner support.
Secure by turning the cams ½
turn clockwise.
1
Merino | 14
Step 3
Installing Stanchions
(If wall hung, skip to step 5)
Loosen the stanchion channel
bolts. Do not remove.
Slide the stanchions in the
channels. Adjust glides on the
stanchions until scribe line is
flush with work surface.
Tighten the stanchion channel
bolts.
Attach cross members using
3/8” bolts.
Scribe line
Work-surface
Loosen
Merino | 15
Step 4
Installing Tack Board & Overhead
Attach the tack board using
the pre installed “Z” clips on
the back side. Press down to
fully engage.
Hang the overhead on the top
of the stanchions.
Adjust side to side to align
with work surface.
Merino | 16
Step 5
Attaching the Access Panel
Align the access panel so the
raffix connectors are in line
with the studs.
Place on studs and tighten
with a phillips screwdriver by
turning clockwise.
Merino | 17
Step 6
Installing Wall Mounted Tack Board & Overhead
Ensure work surface is level.
Reference numbers in the
table below. Measurements
are to the bottom of cleat.
Attach wall cleats. (lag screws
for a backed wall, toggles for
non backed wall.
Install the tack board.
Install the overhead.
“A” dimension
“B” dimension
Open Shelf Case Overhead
Tackboard
Single
High Double
High Single
High Double
High
A
Tackboard
WS 2
Cleat
B
21.25”
x x 31.923” 44.173”
21.25”
15.648”
23.5”
32.049”
x 34.173” x
23.5”
17.898”
33.5”
42.049”
x 44.173” x
33.5”
27.898”
21.844”
x 42.05” x x
21.844”
16.242”
Merino | 18
Step 7
Attaching the Sliding Hood
Remove the wing nuts from
the track on the back of the
overhead.
Lifting hood over the back of
the overhead, carefully align
the holes on the hood with the
studs in the tracks.
Attach wing nuts to secure
hood on the overhead.
Merino | 19
Step 8
Installing Glass Desk
Locate the glass top. (shipped
loose)
With the desk in place and
properly leveled (leveling is
important to ensure a proper
miter alignment) place glass
top in place.
Use glass pods for this
installation.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19

Nucraft Merino T-Shape Installation Instructions Manual

Brand
Nucraft
Model
Merino T-Shape
Type
Installation Instructions Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents