Honeywell DCM/SN DIFF Operating instructions

Brand: Honeywell

Model: DCM/SN DIFF

Type: Operating instructions

Honeywell DCM/SN DIFF is a versatile electronic differential pressure switch and transmitter that can be used in various industrial applications. It offers precise pressure measurement, reliable switching, and flexible configuration options.

Key Capabilities:

Differential Pressure Measurement: Accurately measures the pressure difference between two points.
Switching Functionality: Provides two independent switching outputs for controlling external devices based on pressure conditions.
Analog Output: Transmits a continuous analog signal proportional to the measured pressure difference.

Key Capabilities:

Differential Pressure Measurement: Accurately measures the pressure difference between two points.
Switching Functionality: Provides two independent switching outputs for controlling external devices based on pressure conditions.
Analog Output: Transmits a continuous analog signal proportional to the measured pressure difference.

 U.S Registered Trademark

Smart DCM/SN DIFF

ELECTRONIC DIFFERENTIAL PRESSURE SWITCHES AND TRANSMITTERS (WITH/WITHOUT HMI)

ELEKTRONISCHE DIFFERENZDRUCKSCHALTER UND -TRANSMITTER (MIT/OHNE HMI)

MOUNTING INSTRUCTIONS / MONTAGEANLEITUNG

INCLUDED IN

DELIVERY

IM LIEFERUMFANG

ENTHALTEN

)

MU1B-0402GE51 MU2B-0343GE51

MOUNTING INSTRUCTIONS

MONTAGEANLEITUNG

OPERATING INSTRUCTIONS

BEDIENUNGSANLEITUNG

B) B)

Smart

DCM/SN

DIFF

Smart

DCM/SN

DIFF

ODER

TIGHTEN FESTZIEHEN

OPTION:

MAU8/Ms

OPTION:

MAU8/Nst

6.4

/4"

M12x1

Ø8

Ø6.4

1/4"

WAF

M12x1

19 mm

MAX.

25 Nm

SUPPLY VOLTAGE / VERSORGUNGSSPANNUNG

18...35 VDC 18...35 VDC 18...35 VDC

24 VAC, +10%...-20%

PS... PT...V3PT...A2

111222

4333

P+

P+P+

V(+)

P-P-

n/a

WARN WARN

OC PNP

+P+

n/a

WARN WARN

n/a

PNP

P- GNDP-

U/I

ATTACH WIRES TO

SCREW TERMINALS. DRÄHTE MIT

KLEMMEN VERBINDEN.

VERDRAHTUNGWIRING

BEFORE MOUNTING

Ensure line is

cool and not

under pressure.

IMPORTANT!

To protect sensor

against one-sided

overpressure and

possible damage

while starting

up, first install

a pressure com-

pensation valve.

VOR DER MONTAGE

WICHTIG!

Sicherstellen,

dass die Leitung

drucklos und

kühl ist.

Zum Schutz des Sen-

sors vor einseitiger

Überdruck und ev.

Zerstörung während

der Befüllung ist

zuerst ein Druck-

ausgleichshahn

einzubauen!

SCREWING

DEPTH

EINSCHRAUB-

TIEFE

MAX. 12-13 mmMAX. 12-13 mm

{

3-4X

PREPARE FOR WIRING ZUR VERDRAHTUNG

B C D

NSCREW AND

EMOVE PLUG HEAD. STECKERKOPF ÖFFNEN

UND ABNEHMEN.

USE PROPER WIRE

END SLEEVES. PASSENDE ADERNEND-

HÜLSEN VERWENDEN.

INSERT CABLE. KABEL EINFÜHREN.

LOOSEN GLAND. VERSCHRAUBUNG LÖSEN.

A,B

AWG 18 /

0.75 mm

4…6 mm

REASSEMBLY ZUSAMMENBAU

3-4X

SMART DCM, SN DIFF (WITH/WITHOUT HMI) - MOUNTING INSTRUCTIONS



Manufactured for and on behalf of the Environmental & Energy Solutions Division of Honeywell Technologies Sàrl, Rolle, Z.A. La Pièce 16, Switzerland by its Authorized Representative:

Home and Building Technologies

Honeywell GmbH

Böblinger Strasse 17

71101 Schönaich, Germany

phone: (49) 7031-637-02

fax: (49) 7031-637-850

Subject to change without notice. Printed in Germany

MU1B-0402GE51 R0817D www.fema.biz

ODER

FASTEN PLUG

(approx. 0.5 Nm)

STECKER BEFESTIGEN

(ca. 0,5 Nm)

INSTALLATION

CAUTION

Before mounting or dismounting the unit, ensure that the

system is without pressure and without electrical current!

Process parts may be hot! Danger of personal injury due to

hot process parts. Always allow the unit (and attached pipes)

to cool down before mounting / dismounting the unit.

Mounting and Orientation

The device is mounted directly to the pipe via two G¼" pro-

cess connections (Width Across Flats: 19 mm). This process

connection serves to fasten and secure the device in place.

All mounting orientations are permitted.

Electrical Connection

All wiring must comply with applicable electrical codes and

local ordinances (e.g. in Germany, in accordance with VDE

regulations).

Pin Assignment of Plug

The plug is an A-coded, four-prong M12 plug (see also figure

4 on page 1).

Accessories (ordered separately)

Included in delivery: M12x1 Angled plug.

Optional: ST12-5-G (straight M12x1 plug)

MAU8/Ms adapter, 8 mm, yellow brass

MAU8/Nst adapter, 8 mm, stainless steel

INSTALLATION

VORSICHT

Vor dem Ein-/Ausbau Anlage drucklos machen und entleeren!

Spannungsfrei schalten!

Anlagenteile und Gerät können heiß sein! Verbrennungs-

gefahr! Gerät nur im abgekühlten Zustand montieren oder

abmontieren.

Montage und Ausrichtung

Das Gerät wird mittels zwei Prozeßanschlußgewinde G¼"

(Schlüsselweite 19 mm) direkt in die Druckleitung geschraubt.

Damit wird der Druckanschluß hergestellt und das Gerät

sicher in Position gehalten. Sämtliche Einbaulagen zulässig.

Elektrischer Anschluß

Die gesamte Verdrahtung muß gemäß den landes-

spezifischen Regeln und Normen durchgeführt werden (z.B.

in Deutschland nach VDE).

Kontaktbelegung des Steckers

Der Stecker ist ein A-codierter 4-poliger Stecker (siehe Bild 4

auf Seite 1).

Zubehör (extra zu bestellen)

Im Lieferumfang enthalten: M12x1 Winkelstecker.

Optional: ST12-5-G (gerader M12x1 Stecker)

MAU8/Ms Adapter, 8 mm, Messing

MAU8/Nst Adapter, 8 mm, Edelstahl

Honeywell DCM/SN DIFF Operating instructions

Brand: Honeywell

Model: DCM/SN DIFF

Type: Operating instructions

Key Capabilities:

Differential Pressure Measurement: Accurately measures the pressure difference between two points.
Switching Functionality: Provides two independent switching outputs for controlling external devices based on pressure conditions.
Analog Output: Transmits a continuous analog signal proportional to the measured pressure difference.

Download PDF

report

in other languages

Deutsch: Honeywell DCM/SN DIFF Bedienungsanleitung

Honeywell DCM/SN DIFF Operating instructions

Honeywell DCM/SN DIFF Operating instructions

in other languages

Related papers

Other documents