1 2 3 4
65 7 8
An iOS (12.0 or later) or Android (8.0 or later)
mobile device.
NOTE: Make sure Wi-Fi and Bluetooth are enabled on
your mobile device.
A My Leviton cloud account
(set up through the My Leviton app).
A 2.4GHz Wi-Fi network with high
speed internet.
Installation requires electrical knowledge.
If you are unsure of any steps, consult an electrician.
Getting Started Guide
Cat. No. D215S
SWITCH
2
ND
GEN
See the complete line of My Leviton
TM
app compatible
dimmers, switches, plug-ins, and controllers at
leviton.com/decorasmart
Features
Before you install Identify your wires
What you need to make
it work:
Your switch
works with:
Leviton’s second-generation
Decora Smart Wi-Fi Switch makes
it easier than ever to control your
lights how you want. Use your
voice with Amazon Alexa, Google
Assistant, or Apple Siri — or
use your smartphone or tablet
to control lighting with the My
Leviton app, even when you’re
away from home.
The Decora Smart Wi-Fi Switch
looks right at home with your
other Decora devices and can
be combined with other Decora
Smart Wi-Fi devices to create a
Whole Home experience with room
scenes, activities, and schedules
for connected lights to match
your lifestyle.
• General purpose loads up to
15 amps, for specific ratings see
the chart below.
• Do not use your switch with metal
wall plates or aluminum wire.
• Additional self-service support
options can be found in the
My Leviton app or
at leviton.com/decorasmart.
RATINGS
General Use 15A, 120VAC, 60Hz
LED / CFL / Electr
onic Ballast 5A
Incandescent / Halogen 1500W
Magnetic Ballast 15A
Motor 3/4 HP
Operating Temp 0°C - 40°C (32°F - 104°F)
Operating Humidity 0 - 90% non-condensing
NETWORK
Wi-Fi 802.11 b/g/n networks - 2.4GHz only
Security
WPA, WPA2, or WPA3 security, or open
Bluetooth v5.0
MY LEVITON APP
iOS version 12.0 or later
Andr
oid version 8.0 or later
DI-000-D215S-02A
Rocker
• Press the top to turn ON.
• Press the bottom to turn
light OFF.
Status LED
• Illuminates when the lights
are off so you can find the
switch in the dark.
• Provides connectivity and
device status feedback.
• Advanced settings available
in the My Leviton app.
Check your wall box:
1. Remove wallplate and disconnect existing switch.
2. Restore power. Carefully test wires with voltage tester to
find the line (hot) wire.
3. Turn off power at the circuit breaker.
4. Mark the wires as shown below. Please note neutral wires
are required to operate this device.
Quick tip: Neutral wires are typically white and will be
found bundled inside the electrical box.
Single pole installation:
1. Work only one connection at a time.
2. Connect wires as shown using the included
wire connectors.
1. Restore power. Status LED should flash GREEN indicating
your switch is ready to be enrolled.
2. After powering on the switch to confirm it is receiving
power, turn the power back off again at the breaker prior
to completing the installation.
Wire your switch
Test and install
Welcome
Things to consider:
To control the switch from more than one location such
as in a 3-way or multi-way, you will need either a wired
DD0SR Companion device, or a wireless DAWSC Anywhere
Companion device. See Switch Companion instructions for
connection directions.
If your wall box looks different, call an electrician.
If your wall box contains a different wiring
configuration, contact Leviton’s technical support
team or consult an electrician.
WARNING: TO AVOID FIRE, SHOCK OR DEATH, turn off
power at the circuit breaker.
NOTE:
• Neutral connection is required.
• The YELLOW/RED traveler wire is only used in 3-way
applications; remember to put a wire connector on the
YELLOW/RED traveler wire even if not in use.
If you need help...
ONLINE
decorasmartsupport.leviton.com
CHAT
www.leviton.com/support
EMAIL
CALL
1-800-824-3005 (USA)
1-800-405-5320 (Canada)
Easy Wi-Fi lighting
control for the
whole home
CHAT
www.leviton.com/support
CALL
1-800-824-3005 (USA)
1-800-405-5320 (Canada)
ONLINE
decorasmartsupport.leviton.com
EMAIL
We are here to help
LINE
LOAD
TRAV
NEUTRAL
GND
GROUND
GROUND
NEUTRAL
To Light
To Light
From
From
Branch Circuit
Branch Circuit
LOAD
LOAD
NEUTRAL
GROUND
GROUND
LINE
LINE
TRAVELER
TRAVELER
GROUND
GROUND
NEUTRAL
LOAD
LOAD
LINE
LINE
To Light
To Light
From
From
Branch Circuit
Branch Circuit
Leviton Manufacturing Co., Inc.
201 North Service Road, Melville, NY 11747
© 2021 Leviton Manufacturing Co., Inc. All rights reserved.
Specifications subject to change at any time without notice.
WEB VERSION
9 10 11 12
1413 15 16
What to do if...
Safety first
Limited 2 Year Warranty &
Exclusions
Visit leviton.com/decorasmart or contact technical services
for additional help.
Switch is wired and installed but the light does
not respond:
• Make sure power has been restored at the circuit breaker.
• Verify wiring connections are correct.
When power is applied to the switch, the light is off and
does not respond:
• For proper operation the switch needs a line (hot), neutral,
load, and ground connection.
• Confirm the white conductor is a neutral.
My lights work but they are flickering:
• Unscrew light bulb and test with voltage tester to make sure
a line (hot) and neutral wire are connected to the light.
Not connected to Wi-Fi:
• If your device is setup in the My Leviton app, select your
device, then select “Device Settings”. On the “Device
Settings” screen, select “Reconfigure Wireless”.
• Follow the prompts to reconfigure your device and update
the Wi-Fi settings.
How do I clean my device?
• To clean use a damp cloth with mild soap. DO NOT use
disinfecting products, including foggers, sprays or other
types of atomized cleaning agents.
For Leviton’s limited product warranty, go to www.leviton.com. For a printed copy of the
warranty, call 1-800-824-3005.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton
in writing at Leviton Manufacturing of Canada ULC to the attention of the Quality Assurance
Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone
at 1 800 405-5320.
FCC COMPLIANCE STATEMENT
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (i.) This device may not cause harmful interference (ii.) This device
must accept any interference received, including interference that may cause undesired
operation. Any changes or modifications not expressly approved by Leviton could void the user’s
authority to operate this equipment. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connec
ted.
• Consult the dealer or an experienced radio/TV technician for help.
FC
C CAUTION
Any changes or modifications not expressly approved by Leviton Manufacturing Co., Inc., could
void the user’s authority to operate the equipment.
FCC SUPPLIER’S DECLARATION OF CONFORMITY
Model D215S – Wi-Fi Switch is manufactured by Leviton Manufacturing Co., Inc. 201 N. Service
Road, Melville, NY 11747. www.leviton.com. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
IC STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
RF EXPOSURE AND CO-LOCATION
To comply with FCC OET Bulletin 65 and ISED RF exposure limits for general population and
uncontrolled exposure, this device shall be installed and operated with a minimum distance of
7.9 inches (20 cm) between the radiator and your body. Also, must not be co-located or operated
in conjunction with any other antenna or transmitter.
Status LED
Diagnostic LED
Please see My.Leviton.com support for additional
diagnostic assistance.
If your device is not connecting to the My Leviton app, the status
LED can be used as a diagnostic tool. Press the top rocker for at
least 2 seconds (but no more than 7 seconds) then release. The
status LED will blink a diagnostic code for 2 seconds.
COLOR ACTIVITY STATUS
Green Flashing
In setup mode and r
eady to be added
to a Wi-Fi network.
Green Slow Blink
Connecting to a Wi-Fi network on
power up.
Green or
Off
Solid
Normal operation, can be configured
in a setup.
Amber Slow Blink
Device is not connected to the Wi-Fi
network but attempting to reconnect.
Green/
Amber
Alternating
Blink
Device is in wireless Anywhere
Companion Pairing Mode.
Red Blink
Wireless Anywhere Companion
devices have unpaired or at max
number of paired devices.
Green/Red/
Amber
Alternating
Blink
Identify feature triggered from the
My Leviton app.
CO LO R STAT US
Amber Not connected to Wi-Fi.
Re
d
Connected to Wi-Fi but not able to connect to
the My Leviton cloud.
Green/Amber,
Alternating
Connected to Wi-Fi and My Leviton cloud but
unable to set the time from the internet.
Green
Connected to Wi-Fi and My Leviton cloud is
working properly.
Setup mode
Factory default reset
WARNINGS:
• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER a
t circuit breaker
or fuse and test that power is off before wiring!
• TO AVOID FIRE, PERSONAL INJURY OR PROPERTY DAMAGE, DO NOT
i
nstall to control a receptacle.
• This product is to be installed and/or used in accordance with electrical
codes
and regulations.
• For indoor use only.
• If you are unsure about any part of these instructions, consult
an
electrician.
CAUTIONS:
• The Decora Smart branded D215S is not compatible with standard 3-way
o
r 4-way switches. Use only (1) Decora Smart branded D215S switch in a
wired multi-location circuit with up to 9 DD0SR-01Z Switch Companions or
up to 4 DD0SR-DLZ Switch Companions.
• Maximum wire length from switch to all installed companion devices
c
annot exceed 300 ft (90m).
• Save this instruction sheet. It contains important technical data along
with testing and troubleshooting information which will be useful after
installation is complete.
• Recommended minimum wall box depth is 2-3/4”.
• Use this switch with copper or copper clad wire only.
• Leviton Wi-Fi enabled devices rely on Wi-Fi communication. For customers
l
ooking to install a large number of devices it is recommended to
consult the wireless network’s access point specifications to determine
the maximum number of supported Wi-Fi devices. In some cases, for
example large installations, it may be necessary to upgrade to newer high
performance wireless grade access points to ensure proper operation.
ADDITIONAL RATINGS:
• Purpose of control: Operating Control
• Action Control Type: 1
• Pollution Degree: 2
• Impulse Voltage: 2500V
• Disconnection Type: Micro
1. Open the My Leviton app.
2. Tap icon to turn ON/OFF.
Test My Leviton
app control
Quick tip
• The My Leviton app includes many features such as:
scheduling, remote control, vacation mode,
auto-shutoff, and room scenes.
• Additional self-service support options can be found
in the My Leviton app or at leviton.com/decorasmart.
Test and install
(continued)
3. Gently push wires
into wall box.
Screw switch
to box.
4. Snap on Decora
®
wallplate and
restore power.
Turn off power at the circuit breaker
before screwing in your switch.
Once power is restored, the status
LED will blink GREEN indicating
your device is in setup mode. See
page 15 if your Status LED is not
blinking GREEN.
Congratulations
Your Decora Smart Switch
is ready to control your light.
To download the app,
visit my.leviton.com and select the link or s
can
the below QR code for your device.
Get the app
Device setup
Add your device to
My Leviton
• Decora Smart Wi-Fi 2
nd
Gen devices can be connected to
the My Leviton service, Apple HomeKit, or both.
• For voice control with Amazon Alexa or Google Assistant,
you will need to setup the device with My Leviton.
• For voice control with Siri, you will need to connect your
device to Apple HomeKit. See page 14 for instructions on
how to add your device to Apple HomeKit.
1. Make sure the device is in setup mode (status LED should
be blinking GREEN). If the status LED is not blinking
GREEN, see page 15 for instructions on how to put the
device in setup mode.
2. Launch the My Leviton app.
3. Log in or choose “Sign Up” for an Account.
4. Follow the instructions on the screen.
5. Once logged in tap the “+” in the bottom menu and select
“Add Device”.
6. Follow the app instructions to add your device and
connect it to your home Wi-Fi network.
Connect to My Leviton
partners (optional)
Visit my.leviton.com for a complete list of
compatible smart home products.
Hey Google
works with
Add your device to Apple
HomeKit (optional)
NOTE: Skip step 1 if your device is already enrolled to My Leviton and
on your Wi-Fi network.
1. Make sure the device is in setup mode (status LED should be
blinking GREEN). If the status LED is not blinking GREEN, see page
15 for instructions on how to put the device into setup mode.
2.
Using an iOS device, open the Apple Home app and select “Add Accessory”.
3. Make sure your Decora Smart Wi-Fi Switch is model number D215S.
Locate and scan the HomeKit setup code on the device or on the
front page of this Getting Started Guide.
4. Follow the instructions in the Apple Home app.
5. Once the device is set up, you will be able to voice control your
Decora Smart switch with Apple Siri.
1.
Hold the top rocker for 7 seconds.
2. After the first 7 seconds the status
light will turn AMBER, then release.
3. The status light will flash GREEN.
The device is now in setup mode.
1.
Hold the top rocker for 14 seconds.
2. After the first 7 seconds the status light will turn AMBER.
Continue to hold.
3. After 7 more seconds, the status light will quickly flash
RED/AMBER.
4. Release the top rocker and the device will reset.
1. Tap menu icon in lower
right corner.
2. Tap Integrations, locate the
desired service, select and
follow the instructions.
Copyright and Trademark Information
Decora and Decora Smart are the registered trademarks of Leviton Manufacturing Co., Inc., registered in the
U.S., Canada, Mexico and China.
Google and Google Play are trademarks of Google LLC. Alexa, and related logos are trademarks of Amazon.
com, Inc. or its affiliates. Apple
®
, HomeKit
®
, and Siri
®
are trademarks of Apple Inc., registered in the U.S. and
other countries. IFTTT and the Wi-Fi CERTIFIED logo are trademarks of their respective owners and any use
of such marks by Leviton is under license.
Use of the Works with Apple badge means that an accessory has been designed to work specifically with
the technology identified in the badge and has been certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this device or its compliance with safety and
regulatory standards.
Use herein of other third party trademarks, service marks, trade names, brand names and/or product names
are for informational purposes only, are/may be the trademarks of their respective owners; such use is
not meant to imply affiliation, sponsorship, or endorsement. No part of this document may be reproduced,
transmitted or transcribed without the express written permission of Leviton Manufacturing Co., Inc.
Copyright 2021 Leviton Mfg. Co., Inc.
WEB VERSION
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Leviton D26HD-1BW User guide
-
CLOUDY BAY Lighting Supply User manual
-
Leviton D215S-1BW Installation guide
-
-
-
-
-
-
Leviton D2150 User guide
-
dewenwils HODT12C User manual
