JRC JMA-610 Series User manual

RIVER RADAR

EQUIPMENT

INSTRUCTION

MANUAL

- i -

PREFACE

Thank you very much for purchasing the JRC marine radar equipment, JMA-610.

This equipment is a river radar equipment designed to obtain safe operation of ships.

This equipment consists of a radar signal processing unit, a LCD display unit and a scanner unit as its main

units.

● Before operating the equipment, be sure to read this instruction manual carefully for correct operation.

● Maintain this instruction manual so that operators can refer to it at anytime.

Refer to this manual when any inconvenience or defect occurs.

- ii -

●BEFORE OPERATION●

Pictorial Indication

Various pictorial indications are included in this manual and are shown on these equipment so that you can

operate them safety and correctly and prevent any danger to you and/or to other persons and any damage to

your property during operation. Such indications and their meanings are as follows.

Please understand them before you read this manual:

DANGER

This indication is shown where incorrect equipment operation due to

negligence may cause death or serious injuries.

WARNING

This indication is shown where any person is supposed to be in

danger of being killed or seriously injured if this indication is

neglected and these equipment are not operated correctly.

CAUTION

This indication is shown where any person is supposed to be injured

or any property damage is supposed to occur if this indication is

neglected and these equipment are not operated correctly.

Examples of Pictorial Indication

Electric Shock

The U mark represents CAUTION (including DANGER and WARNING).

Detailed contents of CAUTION (“Electric Shock” in the example on the

left.) is shown in the mark.

Disassembling

Prohibited

The  mark represents prohibition.

Detailed contents of the prohibited action (“Disassembling Prohibited” in the

example on the left.) is shown in the mark.

Disconnect the

power plug

The  mark represents instruction.

Detailed contents of the instruction (“Disconnect the power plug “ in the

example on the left.) is shown in the mark.

Warning Label

There is a warning label on the top cover of the equipment.

Do not try to remove, break or modify the label.

- iii -

Never conduct inspection or repair work of equipment

components.

Inspection or repair work by uncertified personnel may

result in fire hazard or electrocution.

For inspection and repair work of equipment

components, consult with our branch office, branch

shop, sales office, or our distributor in your district.

When conducting maintenance, make sure to turn the

main power off.

Failure to comply may result in electrocution.

Turn off the main power before cleaning the equipment.

Especially when a rectifier is used, make sure to turn it

off since voltage is still outputted from the rectifier even

after the indicator and the radar are turned off. Failure to

comply may result in equipment failure, or death or

serious injury due to electric shock.

When conducting maintenance work on the antenna,

make sure to turn its main power off.

Failure to comply may result in electrocution or injuries.

Make sure to turn off the antenna operation switch.

Failure to comply may result in injuries caused by

physical contact with the rotating antenna.

●PRECAUTIONS●

DANGER

- iv -

WARNING

Never carry out internal inspection or repair work of the

equipment by users.

Inspection or repair work by unauthorized personnel may

result in fire hazard or electric shock.

Ask the nearest branch, business office or a dealer for

inspection and repair.

Turn off the main power before maintenance work.

Otherwise, an electric shock may result.

Turn off the main power before cleaning the equipment.

Especially, make sure to turn off the indicator if a rectifier

is used. Otherwise, equipment failure, or death or

serious injury due to electric shock may result, because

voltage is outputted from the rectifier even when the

radar is not operating.

Turn off the main power if you need to be near the

scanner unit for maintenance or inspection purposes.

Direct exposure to electromagnetic waves at close range

in death or serious injury.

Turn off the main power source before starting

maintenance.

Otherwise, an electric shock or injury may be caused.

When conducting maintenance work, make sure to turn

off the power and unplug the power line of the processor

so that the power supply to the equipment is completely

cut off.

Some equipment components can carry electrical current

even after the power switch is turned off, and conducting

maintenance work without unplugging the power

connector may result in electrocution, equipment failure,

or accidents.

- v -

Set the safety switch for stopping the scanner unit to the

OFF position.

Otherwise, an accidental contact with the rotating

scanner unit may cause injury.

Turn off the main power source before starting

maintenance.

Otherwise, an electric shock or injury may be caused.

Turn off the main power if you need to be near the

scanner unit for maintenance or inspection purposes.

Direct exposure to electromagnetic waves at close range

in death or serious injury.

WARNING

When cleaning the screen, do not wipe it too strongly

with a dry cloth. Also, do not use gasoline or thinner to

clean the screen. Otherwise the screen surface may be

damaged.

Never carry out internal inspection or repair work of the

equipment by users.

Inspection or repair work by unauthorized personnel may

result in fire hazard or electric shock.

Ask the nearest branch, business office or a dealer for

inspection and repair.

Turn off the main power before maintenance work.

Otherwise, an electric shock may result.

Turn off the main power before cleaning the equipment.

Especially, make sure to turn off the indicator if a rectifier

is used. Otherwise, equipment failure, or death or

serious injury due to electric shock may result, because

voltage is outputted from the rectifier even when the

radar is not operating.

- vi -

Set the safety switch for stopping the scanner unit to the

OFF position.

Otherwise, an accidental contact with the rotating

scanner unit may cause injury.

CAUTION

When disposing of used lithium batteries, be sure to

insulate the batteries by taping

○

+ and

○

- terminals.

Otherwise, heat generation, explosion or a fire may occur.

WARNING

When using the [RAIN] function, never set the

suppression level too high canceling out all image noises

from the rain or snow at the close range.

Detection of not only echoes from the rain or snow but

also targets such as other ships or dangerous objects will

become inhibited.

When using the [RAIN] function, make sure to choose the

most appropriate image noise suppression level.

A malfunction may occur if the power in the ship is

instantaneously interrupted during operation of the radar.

In this case, the power should be turned on again.

When using the [SEA] function, never set the

suppression level too high canceling out all image noises

from the sea surface at close range.

Detection of not only echoes from waves but also targets

such as other ships or dangerous objects will become

inhibited.

When using the [SEA] function, make sure to choose the

most appropriate image noise suppression level.

- vii -

Turn off the main power source before replacing parts.

Otherwise, an electric shock or trouble may be caused.

Before replacing the magnetron, turn off the main power

source and wait for 5 minutes or more until the high

voltage circuits are discharged.

Otherwise, an electric shock may be caused.

Take off your wrist watch when bringing your hands close

to the magnetron.

Otherwise, your watch may be damaged because the

magnetron is a strong magnet.

Two or more persons shall replace the liquid crystal

monitor.

If only one person does this work, he may drop the LCD,

resulting in injury.

Even after the main power source is turned off, some

high voltages remain for a while.

Do not contact the inverter circuit in the LCD with bare

hands. Otherwise, an electric shock may be caused.

The accuracy from the vectors are depending on the

accuracy from the (D)GPS sensors.

With longer vectors, the accuracy will be lower.

The vectors are calculated with the situation at that time.

When there will be some changed influence from wind,

water current etc, are not shown before the vessel is

influenced by this.

CAUTION

Do not put watches, clocks, or magnetic cards close to

the modulator unit since this unit holds magnetrons

having strong magnetic force. Failure or data

destruction of the above devices may result.

- viii -

◆◆◆PRECAUTIONS BEFORE OPERATION◆◆◆

■Cautions for high voltage

High voltages from hundreds volts to tens of thousands volts are to be applied to the electronic

equipment such radio and radar devices. You do not face any danger during normal operation,

but sufficient cares are required for maintenance, inspection and adjustment of their internal

components. (Maintenance, check-up and adjustment of the inside of the equipment are prohibited

except by maintenance specialists.)

High voltages of tens of thousands volts are so dangerous as to bring an instantaneous death from

electric shock, but even voltages of hundred volts may sometimes lead to a death from electric

shock. To prevent such an accident, make it a rule to turn off the power switch, discharge

capacitors with a wire surely earthed on an end make sure that internal parts are no longer charged

before you touch any parts inside these devices. At the time, wearing dry cotton gloves ensures

you further to prevent such danger. It is also a necessary caution to put one of your hands in the

pocket and not to use your both hands at the same time.

It is also important to select a stable foothold always to prevent additional injuries once you were

shocked by electricity. If you were injured from electric shock, disinfect the burn sufficiently

and get it taken care of promptly.

■What to do in case of electric shock

When finding a victim of electric shock, turn off the power source and earth the circuit

immediately.

If it is impossible to turn off the circuit, move the victim away promptly using insulators such as

dry wood plate and cloth without touching the victim directly.

In case of electric shock, breathing may stop suddenly if current flows to the respiration center in

the brain. If the shock is not so strong, artificial respiration may recover breathing. When

shocked by electricity, the victim will come to look very bad with weak pulse or without beating,

resulting in unconsciousness and rigidity. In this case, it is necessary to perform an emergency

measure immediately.

- ix -

◆◆◆FIRST-AID TREATMENTS◆◆◆

☆First-aid treatments

As far as the victim of electric shock is not in dangerous condition, do not move him and practice

artificial respiration on him immediately. Once started, it should be continued rhythmically.

(1) Do not touch the victim confusedly as a result of the accident, but the rescuer may also get an

electric shock.

(2) Turn off the power source calmly and move the victim away quietly from the electric line.

(3) Call a physician or ambulance immediately or ask someone to call a doctor.

(4) Lay the victim on this back and loosen his necktie, clothes, belt, etc.

(5) a. Examine the victim’s pulse.

b. Examine his heartbeat bringing your ear close to his heart.

c. Examine his breathing bringing the back of your hand or your face close to his face.

d. Check the size of the pupils of his eyes.

(6) Open the victim’s mouth and take out artificial teeth, cigarette or chewing gum if any.

Keep his mouth open, stretch his tongue and insert a towel or the like in his mouth to prevent

the tongue from suffocating. (If it is hard to open his mouth due to set teeth, open it with a

screwdriver and insert a towel in this mouth.)

(7) Then, wipe his mouth so that foaming mucus does not accumulate inside.

- x -

☆When pulse is beating but breathing has stopped

(Mouth-to-mouth respiration) Fig. 1

(1) Tilt the victim’s head back as far as this face looks back. (A pillow may be inserted his neck.)

(2) Push his jaw upward to open his throat wide (to spread his airway).

(3) Pinch the victim’s nostrils and take a deep breath, block his mouth completely with yours

and blow into his mouth strongly. Take a deep breath again and blow into his mouth.

Continue this 10 to 15 times a minutes (blocking his nostrils).

(4) Carefully watch that he has recovered his natural breathing and atop practicing artificial

respiration.

(5) If it is difficult to open the victim’s mouth, insert a rubber or vinyl tube into one of his

nostrils and blow into it blocking the other nostril and his mouth completely.

(6) When the victim recovers consciousness, he may try to stand up suddenly, but let him lie

calmly and serve him with a cup of hot coffee or tea and keep him warm and quiet. (Never

give him alcoholic drinks.)

Method of mouth-to-mouth respiration by raising head

(1) Raise the victim’s head. Support his

forehead with one of your hand and his

neck with the other hand. →1

When you tilt his head backward, the

victim, in most cases, opens his mouth to

the air. This makes mouth-to mouth

respiration easy.

(2) Cover his mouth as widely as possible with

yours and press your cheek against his nose

→2

or, pinch his nostrils with your fingers to

prevent air from leaking. →3

(3) Blow into his lungs. Continue blowing

into his mouth until his breast swells.

Blow into his mouth as quickly as possible

for the first 10 times.

Fig. 1 Mouth-to mouth respiration

- xi -

☆When both pulse and breathing have stopped

Perform the (Cardiac massage) Fig. 2 and (Mouth-to-mouth respiration) Fig. 1

When no pulse has come not to be felt, his pupils are open and no heartbeat is heard, cardiac arrest

is supposed to have occurred and artificial respiration must be performed.

(1) Place your both hands, one hand on the other, on the lower one third area of his breastbone

and compress his breast with your elbows applying your weight on his breast so that it is

dented about 2cm (Repeat compressing his breast 50 times or so a minutes). (Cardiac

massage)

(2) In case of one rescuer,

Repeat cardiac massages about 15 times and blow into his mouth 2 times quickly, and repeat

this combination.

In case of two rescuers,

One person repeats cardiac massages 15 times while the other person blow into his mouth

twice, and they shall repeat this combination. (Perform the cardiac massage and

mouth-to-mouth respiration)

(3) Examine his pupils and his pulse sometimes. When the both have returned to normal, stop

the artificial respiration, serve him with a cup of hot coffee or tea and keep him warm and

calm while watching him carefully. Commit the victim to a medical specialist depending

on his condition. (Never give him alcoholic drinks.) To let him recover from the mental

shock, it is necessary for persons concerned to understand his situations and the necessary

treatment.

Fig. 2 Cardiac massage







FCCPart15.19WarningStatement‐(RequiredforallPart15devices)

THISDEVICECOMPLIESWITHPART15OF THEFCCRULES.OPERATIONISSUBJECTTOTHE

FOLLOWINGTWOCONDITIONS:(1)THISDEVICEMAYNOTCAUSEHARMFULINTERFERENCE,

AND(2)THISDEVICEMUSTACCEPTANYINTERFERENCERECEIVED,INCLUDING

INTERFERENCETHATMAYCAUSEUNDESIREDOPERATION.

FCCPart15.21WarningStatement‐

NOTE:THEGRANTEEISNOTRESPONSIBLEFORANYCHANGESORMODIFICATIONSNOT

EXPRESSLYAPPROVEDBYTHEPARTYRESPONSIBLEFORCOMPLIANCE.SUCH

MODIFICATIONSCOULDVOIDTHEUSER’SAUTHORITYTOOPERATETHEEQUIPMENT.



FCCPart15.105(b)WarningStatement‐(ONLYRequiredfor15.109‐JBPdevices)

NOTE:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassB

digitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovide

reasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.This

equipmentgenerates,usesandcanradiateradiofrequency

energyand,ifnotinstalledand

usedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradio

communications.However,thereisnoguaranteethatinterferencewillnotoccurina

particularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioor

televisionreception,whichcanbedeterminedby

turningtheequipmentoffandon,the

userisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowing

measures:



‐Reorientorrelocatethereceivingantenna.

‐Increasetheseparationbetweentheequipmentandreceiver.

‐Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiver

isconnected.



‐Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

ICRSS‐GEN,Sec7.1.3WarningStatement‐(Requiredforlicense‐exemptdevices)

ENGLISH:

ThisdevicecomplieswithIndustryCanadalicense‐exemptRSSstandard(s).Operationis

subjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseinterference,and(2)

thisdevicemustacceptanyinterference,includinginterferencethatmaycauseundesired

operationofthedevice.



FRENCH:

LeprésentappareilestconformeauxCNRd'IndustrieCanadaapplicablesauxappareilsradio

exemptsdelicence.L'exploitationestautoriséeauxdeuxconditionssuivantes:(1)l'appareil

nedoitpasproduiredebrouillage,et(2)l'utilisateurdel'appareildoitacceptertout

brouillageradioélectriquesubi,mêmesilebrouillageestsusceptibled'encompromettre

le

fonctionnement.



ICRSS‐GEN,Sec7.1.2WarningStatement‐(RequiredforTransmitters)

ENGLISH:

UnderIndustryCanadaregulations,thisradiotransmittermayonlyoperateusingan

antennaofatypeandmaximum(orlesser)gainapprovedforthetransmitterbyIndustry

Canada.Toreducepotentialradiointerferencetootherusers,theantennatypeanditsgain

shouldbesochosenthattheequivalentisotropicallyradiated

power(e.i.r.p.)isnotmore

thanthatnecessaryforsuccessfulcommunication.

FRENCH:

Conformémentàlaréglementationd'IndustrieCanada,leprésentémetteurradiopeut

fonctionneravecuneantenned'untypeetd'ungainmaximal(ouinférieur)approuvépour

l'émetteurparIndustrieCanada.Danslebutderéduirelesrisquesdebrouillage

radioélectriqueàl'intentiondesautresutilisateurs,ilfautchoisirletyped'antenneet

son

gaindesortequelapuissanceisotroperayonnéequivalente(p.i.r.e.)nedépassepas

l'intensiténécessaireàl'établissementd'unecommunicationsatisfaisante.







ICRSS‐GEN,Sec7.1.2WarningStatement‐

(RequiredforTransmittersw/detachableantennas)

ENGLISH:

Thisradiotransmitter(identifythedevicebycertificationnumber,ormodelnumberif

CategoryII)hasbeenapprovedbyIndustryCanadatooperatewiththeantennatypeslisted

belowwiththemaximumpermissiblegainandrequiredantennaimpedanceforeach

antennatypeindicated.Antennatypesnotincludedinthislist,havingagaingreaterthan

themaximumgainindicatedforthattype,arestrictly

prohibitedforusewiththisdevice.



‐ 6ftantennaNAX‐16B‐6,29.2(dBi)1.2°(horizontal)20.9°(vertical)

‐ 7ftantennaNAX‐16A‐7,29.2(dBi)1.0°(horizontal)24.0°(vertical)

‐ 9ftantennaNAX‐16A‐9,30.2(dBi)0.8°(horizontal)25.0°(vertical)

FRENCH:

Leprésentémetteurradio(identifierledispositifparsonnumérodecertificationouson

numérodemodèles'ilfaitpartiedumatérieldecatégorieI)aétéapprouvéparIndustrie

Canadapourfonctionneraveclestypesd'antenneénumérésci‐dessousetayantungain

admissiblemaximaletl'impédancerequisepourchaque

typed'antenne.Lestypes

d'antennenoninclusdanscetteliste,oudontlegainestsupérieuraugainmaximalindiqué,

sontstrictementinterditspourl'exploitationdel'émetteur.

ICRSS‐102,Sec2.6WarningStatements

ENGLISH:

Theapplicantisresponsibleforprovidingproperinstructionstotheuseroftheradiodevice,

andanyusagerestrictions,includinglimitsofexposuredurations.Theusermanualshall

provideinstallationandoperationinstructions,aswellasanyspecialusageconditions,to

ensurecompliancewithSARand/orRFfieldstrengthlimits.For

instance,compliance

distanceshallbeclearlystatedintheusermanual.

Englsh:

Theusermanualofdevicesintendedforcontrolleduseshallalsoincludeinformation

relatingtotheoperatingcharacteristicsofthedevice;theoperatinginstructionstoensure

compliancewithSARand/orRFfieldstrengthlimits;informationontheinstallationand

operationofaccessoriestoensurecompliancewithSARand/orRFfieldstrength

limits;and

contactinformationwheretheusercanobtainCanadianinformationonRFexposureand

compliance.Otherrelatedinformationmayalsobeincluded.

French:Lemoded'emploidesappareils destinésà l'utilisationcontrôléedoitaussiinclure

desinformationssurlescaractéristiquesdefonctionnementdel'appareil;lesinstructionsde

fonctionnementpourassurerlaconformitéavecSARet/ouleslimitesd'intensitédechamp

RF;informationssurl'installationetl'exploitationd'accessoirespourassurerlerespect

des

SARet/ouleslimitesd'intensitédechampRF;etlescoordonnéesoùl'utilisateurpeut

obtenirdesinformationssurl'expositioncanadiennederadiofréquencesetlaconformité.

Autresrenseignementsconnexespeuventégalementêtreinclus.





- xii -

GLOSSARY

This section describes the main terms used for this equipment and general related maritime terms.

AZI MODE (Azimuth Stabilization MODE):

Bearing display mode

Anti-clutter rain (FTC):

Rain/snow clutter suppression

Anti-clutter sea (STC):

Sea clutter suppression

BRG:

Bearing

COG (Course Over Ground):

Course relative to the ground.

CUP (Course-Up):

Own ship’s course is pointed to the top

center of the radar display.

EBL (Electronic Bearing Line):

An electronic bearing line originated from

own ship’s position.

ENH (Enhance):

A target can be enlarged.

GND:

Stabilization relative to the ground.

GPS (Global Positioning System):

The position of a GPS receiver can be

determined by the signals from GPS

satellites.

HDG (Heading):

Own ship’s heading bearing.

The display ranges from 000 to 360 degrees

as scanned clockwise.

HL (Heading Line):

Ship’s heading line

HUP (Head-Up):

Own ship’s heading line is always pointed to

the top center of the radar display.

IR (Interference Rejector):

Radar interference rejector

MRK (Mark):

Reflection plot

NM (Nautical Mile):

1NM=1852m

NUP (North-Up):

The north is always pointed to the top center

of the radar display.

PIN:

Information set by the user (personal code)

Relative Vector:

A target’s movement predicted relative to

own ship.

RR (Range Rings):

Fixed range ring

RM (Relative Motion):

Relative motion presentation

Own ship’s position is fixed and other

targets move relative to own ship.

SCANNER:

Antenna

SEA:

Sea clutter suppression

SOG (Speed Over Ground):

Speed relative to the ground.

TM (True Motion):

True motion presentation

A presentation in which own ship and any

other target move depending on their

individual movements.

TRAILS:

Function of displaying tracks of other ships.

True Vector:

A target’s true movement predicted as the

result of entering own ship’s direction and

speed.

VRM:

Variable Range Marker

- xiii -

CONTENTS

PREFACE................................................................................................................i

BEFORE OPERATION ........................................................................................... ii

PRECAUTIONS..................................................................................................... iii

GLOSSARY..........................................................................................................xv

1. GENERAL AND EQUIPMENT COMPOSITION

1.1 FUNCTIONS........................................................................................... 1-1

1.1.1 FUNCTION OF THIS SYSTEM .............................................................. 1-1

1.2 FEATURES............................................................................................. 1-2

1.3 CONFIGURATION .................................................................................. 1-3

1.4 EXTERIOR DRAWINGS......................................................................... 1-4

1.5 GENERAL SYSTEM DIAGRAMS........................................................... 1-8

2. NAMES AND FUNCTIONS OF CONTROL PANEL

SWITCHES AND FUNCTIONS OF SOFTWARE BUTTONS

2.1 NAMES AND FUNCTIONS OF CONTROL PANEL ................................ 2-2

2.2 MENU LIST............................................................................................. 2-6

2.3 NAMES AND FUNCTIONS OF ON-SCEEN CONT.............................. 2-17

3. BASIC OPERATION

3.1 FLOW OPERATION................................................................................ 3-1

3.1.1 POWER ON AND START THE SYSTEM ............................................... 3-2

3.1.2 OBSERVE AND ADJUST VIDEO ........................................................... 3-3

3.1.3 ACQUIRE AND MEASURE DATA .......................................................... 3-3

3.1.4 END THE OPERATION AND STOP THE SYSTEM................................ 3-4

3.2 MENU COMPOSITION........................................................................... 3-5

3.3 PREPARATION....................................................................................... 3-9

3.3.1 ADJUST DISPLAY BRILLIANCE [BRILL] ............................................... 3-9

3.3.2 ADJUST OPERATION PANEL BRILLIANCE [PANEL] ........................... 3-9

- xiv -

3.3.3 SWITCH DAY/NIGHT MODE [DAY/NIGHT] ............................................3-9

3.3.4 ADJUST BRILLIANCE OF INFORMATION ON RADAR DISPLAY

(BRILLIANCE SETTING) ......................................................................3-10

3.3.5 ADJUST SOUND VOLUME (BUZZER VOLUME).................................3-10

3.3.6 RESET ALARM BUZZER [ALARM ACK]............................................... 3-11

3.3.7 SET DISPLAY COLOR.......................................................................... 3-11

3.4 BASIC OPERATIONS ...........................................................................3-12

3.4.1 START TRANSMISSION [TX] ...............................................................3-12

3.4.2 STOP TRANSMISSION [STBY] ............................................................3-12

3.4.3 CHANGE RANGE (OBSERVATION RANGE SCALE) [+RANGE-] .......3-13

3.4.4 TUNE ....................................................................................................3-13

3.4.5 CONTROL SENSITIVITY [GAIN] ..........................................................3-14

3.4.6 SUPPRESS SEA CLUTTER [SEA] .......................................................3-14

3.4.7 SUPPRESS RAIN/SNOW CLUTTER [RAIN] ........................................3-15

3.4.8 REJECT RADAR INTERFERENCE [IR]................................................3-16

3.4.9 HIDE/DISPLAY RANGE RINGS (RINGS) .............................................3-16

3.4.10 HIDE SHIP’S HEADING LINE (HL OFF) ...............................................3-17

3.5 GENERAL OPERATIONS .....................................................................3-18

3.5.1 MOVE CROSS CURSOR MARK BY TRACKBALL...............................3-18

3.5.2 USE EBLS (ELECTRONIC BEARING LINES) [EBL1/EBL2].................3-18

3.5.3 USE VRMS (VARIABLE RANGE MARKERS) [VRM1/VRM2]...............3-20

3.5.4 USE P-LINES (PARALLEL INDEX LINES) [P-LINE] .............................3-22

3.5.5 MOVE OWN SHIP’S DISPLAY POSITION [OFF CENT].......................3-23

3.5.6 DISPLAY OTHER SHIPS’ TRAILS [TRAILS].........................................3-23

3.5.7 DISPLAY OWN VECTOR [OWN VECT]................................................3-25

3.5.8 EDITING OWN MARK...........................................................................3-26

3.5.9 TIME ZONE SETTING ..........................................................................3-34

3.5.10 LOCAL TIME SETTING.........................................................................3-35

3.5.11 CHANGE THE UNIT OF RATE OF TURN.............................................3-36

3.5.12 DISPLAY AIS LABEL.............................................................................3-37

3.5.13 ECHO EXPANSION SWITCH ...............................................................3-37

3.6 DISAPLAY USER MAP .........................................................................3-38

3.6.1 EDIT USER MAP ..................................................................................3-38

3.6.2 CORRECT POSITION ON USER MAP (SHIFT ). .................................3-41

3.6.3 CORRECT POSITION ON USER MAP (SHIFT CLEAR). .....................3-41

3.6.4 SET USER MAP DISPLAY (MARK DISPLAY SETTING) ......................3-42

3.6.5 OPERATE USER MAP FILE (FILE OPERATIONS) ..............................3-52

3.7 SCREEN CAPTURE .............................................................................3-63

3.7.1 SCREEN CAPTURE SETTING (SELECT CARD SLOT). .....................3-63

- xv -

3.7.2 SCREEN CAPTURE SETTING (SAVE FILE). ...................................... 3-65

3.7.3 SCREEN CAPTURE SETTING (ERASE FILE). ................................... 3-66

3.7.4 SCREEN CAPTURE SETTING (AUTO CAPTURE). ............................ 3-67

3.7.5 SCREEN CAPTURE SETTING (AUTO CAPTURE MODE). ................ 3-68

3.7.6 SCREEN CAPTURE SETTING (AUTO CAPTURE INTERVAL)........... 3-69

3.7.7 SCREEN CAPTURE SETTING (AUTO FILE ERASE). ........................ 3-70

3.7.8 SCREEN CAPTURE SETTING (MANUAL CAPTURE). ....................... 3-71

3.8 USER SETTING ................................................................................... 3-72

3.8.1 USER SETTING (LOAD USER SETTING)........................................... 3-72

3.8.2 USER SETTING (SAVE USER SETTING). .......................................... 3-73

3.8.3 USER SETTING (ERASE USER SETTING). ....................................... 3-74

3.9 FORMAT CARD.................................................................................... 3-75

3.9.1 FORMAT CARD (SELECT CARD SLOT). ............................................ 3-75

3.10 AIS FUNCTION .................................................................................... 3-76

3.10.1 VESSEL NAME LIST ............................................................................ 3-76

3.10.2 VESSEL INFORMATION ...................................................................... 3-76

3.10.3 DISPLAY THE VESSEL NAMES ON THE SCREEN ............................ 3-77

3.10.4 AIS SETTING MENU............................................................................ 3-77

3.10.5 AIS SYMBOL ........................................................................................ 3-78

4. MEASUREMENT OF RANGE AND BEARING

4.1 MEASUREMENT BY TRACKBALL ........................................................ 4-1

4.2 MESAUREMENT BY RANE RINGS ....................................................... 4-2

4.3 MESAUREMENT BY EBLS AND VRMS ................................................ 4-3

5. TRUE AND FALSE ECHOES ON DISPLAY

5.1 RADAR WAVE WITH THE HORIZON .................................................... 5-2

5.2 STRENGTH OF REFLECTION FROM THE TARGET............................ 5-4

5.3 SEA CLUTTERS..................................................................................... 5-5

5.4 FALSE ECHOES .................................................................................... 5-6

5.5 DISPLAY OF RADAR TRANSPONDER (SART) .................................... 5-9

- xvi -

6. MAINTENANCE

6.1 ROUTINE MAINTENANCE .....................................................................6-1

6.2 MAINTENANCE ON EACH UNIT............................................................6-2

7. TROUBLE SHOOTING

7.1 FAULT FINDING......................................................................................7-3

7.2 TROUBLE SHOOTING ...........................................................................7-4

7.3 REPLACEMENT OF MAJOR PARTS .....................................................7-7

8. AFTER-SALES SERVICE

9. DISPOSAL

9.1 DISPOSAL OF THE UNIT .......................................................................9-1

9.2 DISPOSAL OF USED BATTERIES .........................................................9-2

9.3 DISPOSAL OF USED MAGNETRON .....................................................9-3

10. SPECIFICATIONS

10.1 JAM-610 TYPE RADAR ........................................................................10-1

10.2 SCANNER (NKE-316)...........................................................................10-2

10.3 CONTROL UNIT (NDC-1486) ...............................................................10-3

10.4 INPUT SIGNAL .....................................................................................10-4

10.5 OUTPUT SIGNAL .................................................................................10-5

10.6 STANDARD EQUIPMENT COMPOSITION ..........................................10-5

10.7 DISTANCE BETWEEN UNITS ..............................................................10-5

APPENDIX

FIG.1 BLOCK DIAGRAM OF JMA-610

FIG.2 TERMINAL DIAGRAM OF JMA-610

FIG.3 PRIMARY POWER SUPPLY BLOCK OF JMA-610

FIG.4 INTERNAL CONNECTION DIAGRAM OF SCANNER UNIT NKE-316

FIG.5 INTERNAL CONNECTION DIAGRAM OF CONTROL UNIT NCM-883

Page is loading ...

JRC JMA-610 Series User manual

This manual is also suitable for

JRC JMA-610 Series User manual

Related papers

Other documents